b20vtec vs. lsvtec
Alright guys so the question is should i build a B20VTEC or an LSVTEC i want alot of power n/a i can play with for next summer..but the summer after that would like to throw it some moderate boost so which would be best to build for speed and reliability
|
LSvtec on boost is around the price of a n/a b20vtec put together. Id have to say LSvtec is the best B series engine for boosting because of cost and a small displacement advantage over the gsr.
|
depends on what you wanna spend but imo LS would be the way to go if you plan on boosting it. b20 cylinder walls are 3mm thinner. you can't build for N/A then just toss on some boost. if you want n/a you'll want high compression but if you want boost, you'll want low compression.
i'm building an N/A ls/vtec cuz the block and head was free and pistons were cheaper. my compression ratio should be in the mid 11's. |
ls/vtec it has more options and is a stronger block.
|
Originally Posted by IntegraMark
(Post 239420)
depends on what you wanna spend but imo LS would be the way to go if you plan on boosting it. b20 cylinder walls are 3mm thinner. you can't build for N/A then just toss on some boost. if you want n/a you'll want high compression but if you want boost, you'll want low compression.
i'm building an N/A ls/vtec cuz the block and head was free and pistons were cheaper. my compression ratio should be in the mid 11's. |
id rethink what u just said because it takes alot more then those minor calculations to hit any of the above stated times
|
ls/vtec FTW
|
would a ls-v swap be cheaper than a b16 or would it be better to get a turbo on a b16 with a nice tune
? my plan iis for this year to run a stock motor maybe some cams i/m and i/h/e than next year save up and build the bottom end and run some serious boost what do u guys think? |
lsvtec has a pretty noticeable torque advantage over the b16 especially off boost, cost roughly the same plus the long geared ls tranny keeps it spoolin. Id say u bolt on turbo kit 6-7psi on that d and run up to 200 whp for less than 1g on stock internals.
|
lol it always gets back to the boosed D everyone saais its the best way to go...if i end up boosting the D what turbo set up should i use and which tranny has the best gearing for boost?
|
o and whats the best to tune with? i was tihnking of the hondata s300 or chrome or uberdata..so whats the best and cheapest to tune boosted motors
|
its all custom or greddy, apexi kits, just dont buy ebay chrome turbos
like 1g 14b dsm turbos is common, well check out homemadeturbo.com |
i was thinkin of runnin a homemade set up but i dont want I/C pipes an flying off under boost lol lookin to make around 350whp on built motor thinkin of goin t3/4 dont want too much lag but also dont want alot of stress on the motor i wanna no more than 16psi what do you guys think? new to the turbo seen
|
Originally Posted by JDM_tuning
(Post 239691)
would a ls-v swap be cheaper than a b16 or would it be better to get a turbo on a b16 with a nice tune
? my plan iis for this year to run a stock motor maybe some cams i/m and i/h/e than next year save up and build the bottom end and run some serious boost what do u guys think? cheap. fast. reliable. <--- Pick two.
Originally Posted by JDM_tuning
(Post 239725)
o and whats the best to tune with? i was tihnking of the hondata s300 or chrome or uberdata..so whats the best and cheapest to tune boosted motors
|
Anyone know of someone selling a good B20 Vtec build?
|
All times are GMT -4. The time now is 07:41 AM. |
© 2024 MH Sub I, LLC dba Internet Brands