1988 Honda Accord Lxi rev'ing Up and Down
Got a question maybe someone can answer...
My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and down after warming up. I thought maybe the vacuum adv. on the distributor might be bad, but verifing timing (pulling hoses and blocking/ chk timing) all are alright (car does not rev up and dwn when I do this). But once I put the hoses back same thing. If I pull the hose closest to the front end of the car, the engine stops rev'ing up and dwn. Another thing I did is replacing the all hoses to vacuum adv, I disconnected the power plug to the vacuum control module (left portion of firewall) and the car stops rev'ing up and down. SUGGESTIONS???? |
Re: 1988 Honda Accord Lxi rev'ing Up and Down
Best I can think of: turn the heat to max and bleed coolant. Remove the
battery for a minute to reset ECU. > My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and down > after warming up. I thought maybe the vacuum adv. on the distributor > might be bad, but verifing timing (pulling hoses and blocking/ chk > timing) all are alright (car does not rev up and dwn when I do this). > But once I put the hoses back same thing. If I pull the hose closest to > the front end of the car, the engine stops rev'ing up and dwn. Another > thing I did is replacing the all hoses to vacuum adv, I disconnected the > power plug to the vacuum control module (left portion of firewall) and the > car stops rev'ing up and down. SUGGESTIONS???? |
Re: 1988 Honda Accord Lxi rev'ing Up and Down
Best I can think of: turn the heat to max and bleed coolant. Remove the
battery for a minute to reset ECU. > My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and down > after warming up. I thought maybe the vacuum adv. on the distributor > might be bad, but verifing timing (pulling hoses and blocking/ chk > timing) all are alright (car does not rev up and dwn when I do this). > But once I put the hoses back same thing. If I pull the hose closest to > the front end of the car, the engine stops rev'ing up and dwn. Another > thing I did is replacing the all hoses to vacuum adv, I disconnected the > power plug to the vacuum control module (left portion of firewall) and the > car stops rev'ing up and down. SUGGESTIONS???? |
Re: 1988 Honda Accord Lxi rev'ing Up and Down
Best I can think of: turn the heat to max and bleed coolant. Remove the
battery for a minute to reset ECU. > My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and down > after warming up. I thought maybe the vacuum adv. on the distributor > might be bad, but verifing timing (pulling hoses and blocking/ chk > timing) all are alright (car does not rev up and dwn when I do this). > But once I put the hoses back same thing. If I pull the hose closest to > the front end of the car, the engine stops rev'ing up and dwn. Another > thing I did is replacing the all hoses to vacuum adv, I disconnected the > power plug to the vacuum control module (left portion of firewall) and the > car stops rev'ing up and down. SUGGESTIONS???? |
Re: 1988 Honda Accord Lxi rev'ing Up and Down
Best I can think of: turn the heat to max and bleed coolant. Remove the
battery for a minute to reset ECU. > My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and down > after warming up. I thought maybe the vacuum adv. on the distributor > might be bad, but verifing timing (pulling hoses and blocking/ chk > timing) all are alright (car does not rev up and dwn when I do this). > But once I put the hoses back same thing. If I pull the hose closest to > the front end of the car, the engine stops rev'ing up and dwn. Another > thing I did is replacing the all hoses to vacuum adv, I disconnected the > power plug to the vacuum control module (left portion of firewall) and the > car stops rev'ing up and down. SUGGESTIONS???? |
Re: 1988 Honda Accord Lxi rev'ing Up and Down
ECU re-set is done by removing the ECU fuse for ten seconds. The fuse
is in the under hood fuse box. See if there is something in the intake screen for the vacuum source in the big box full of controls on the passenger side of the outer firewall. (all the vac lines run to it) Good Luck! bob Indian Summer wrote: > > Best I can think of: turn the heat to max and bleed coolant. Remove the > battery for a minute to reset ECU. > > > My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and down > > after warming up. I thought maybe the vacuum adv. on the distributor > > might be bad, but verifing timing (pulling hoses and blocking/ chk > > timing) all are alright (car does not rev up and dwn when I do this). > > But once I put the hoses back same thing. If I pull the hose closest to > > the front end of the car, the engine stops rev'ing up and dwn. Another > > thing I did is replacing the all hoses to vacuum adv, I disconnected the > > power plug to the vacuum control module (left portion of firewall) and the > > car stops rev'ing up and down. SUGGESTIONS???? |
Re: 1988 Honda Accord Lxi rev'ing Up and Down
ECU re-set is done by removing the ECU fuse for ten seconds. The fuse
is in the under hood fuse box. See if there is something in the intake screen for the vacuum source in the big box full of controls on the passenger side of the outer firewall. (all the vac lines run to it) Good Luck! bob Indian Summer wrote: > > Best I can think of: turn the heat to max and bleed coolant. Remove the > battery for a minute to reset ECU. > > > My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and down > > after warming up. I thought maybe the vacuum adv. on the distributor > > might be bad, but verifing timing (pulling hoses and blocking/ chk > > timing) all are alright (car does not rev up and dwn when I do this). > > But once I put the hoses back same thing. If I pull the hose closest to > > the front end of the car, the engine stops rev'ing up and dwn. Another > > thing I did is replacing the all hoses to vacuum adv, I disconnected the > > power plug to the vacuum control module (left portion of firewall) and the > > car stops rev'ing up and down. SUGGESTIONS???? |
Re: 1988 Honda Accord Lxi rev'ing Up and Down
ECU re-set is done by removing the ECU fuse for ten seconds. The fuse
is in the under hood fuse box. See if there is something in the intake screen for the vacuum source in the big box full of controls on the passenger side of the outer firewall. (all the vac lines run to it) Good Luck! bob Indian Summer wrote: > > Best I can think of: turn the heat to max and bleed coolant. Remove the > battery for a minute to reset ECU. > > > My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and down > > after warming up. I thought maybe the vacuum adv. on the distributor > > might be bad, but verifing timing (pulling hoses and blocking/ chk > > timing) all are alright (car does not rev up and dwn when I do this). > > But once I put the hoses back same thing. If I pull the hose closest to > > the front end of the car, the engine stops rev'ing up and dwn. Another > > thing I did is replacing the all hoses to vacuum adv, I disconnected the > > power plug to the vacuum control module (left portion of firewall) and the > > car stops rev'ing up and down. SUGGESTIONS???? |
Re: 1988 Honda Accord Lxi rev'ing Up and Down
ECU re-set is done by removing the ECU fuse for ten seconds. The fuse
is in the under hood fuse box. See if there is something in the intake screen for the vacuum source in the big box full of controls on the passenger side of the outer firewall. (all the vac lines run to it) Good Luck! bob Indian Summer wrote: > > Best I can think of: turn the heat to max and bleed coolant. Remove the > battery for a minute to reset ECU. > > > My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and down > > after warming up. I thought maybe the vacuum adv. on the distributor > > might be bad, but verifing timing (pulling hoses and blocking/ chk > > timing) all are alright (car does not rev up and dwn when I do this). > > But once I put the hoses back same thing. If I pull the hose closest to > > the front end of the car, the engine stops rev'ing up and dwn. Another > > thing I did is replacing the all hoses to vacuum adv, I disconnected the > > power plug to the vacuum control module (left portion of firewall) and the > > car stops rev'ing up and down. SUGGESTIONS???? |
Re: 1988 Honda Accord Lxi rev'ing Up and Down
Indian Summer wrote:
> > Best I can think of: turn the heat to max and bleed coolant. Remove the > battery for a minute to reset ECU. > > > My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and > > down after warming up. I thought maybe the vacuum adv. on the > > distributor might be bad, but verifing timing (pulling hoses and > > blocking/ chk timing) all are alright (car does not rev up and dwn when > > I do this). But once I put the hoses back same thing. If I pull the > > hose closest to the front end of the car, the engine stops rev'ing up > > and dwn. Another thing I did is replacing the all hoses to vacuum adv, > > I disconnected the power plug to the vacuum control module (left > > portion of firewall) and the car stops rev'ing up and down. > > SUGGESTIONS???? I agree with the above suggestion to bleed the coolant. The most common problem associated with the idle cycling up and down is usually due to a lack of coolant flowing through the cold start valve. The valve is item number 8 in this diagram http://tinyurl.com/xj18. If the valve doesn't warm up as the engine warms up (from coolant flowing through the bottom part), the PGMFI system will misinterpret the condition and idle cycling results. The first thing to due is to check the valve and make sure that the lower part of the valve gets hot as the engine warms up. If the valve doesn't get hot, try bleeding the coolant and make sure that coolant is flowing through the valve. You can double check the valve as a source of the cycling by removing the two screws from the top along with the oval shaped plate and push down on the inner valve/plunger in the center. The cycling should stop if the valve is the problem. If the valve is getting hot and pushing the inner plunger down stops the cycling, then the valve likely needs to be replaced. Eric |
Re: 1988 Honda Accord Lxi rev'ing Up and Down
Indian Summer wrote:
> > Best I can think of: turn the heat to max and bleed coolant. Remove the > battery for a minute to reset ECU. > > > My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and > > down after warming up. I thought maybe the vacuum adv. on the > > distributor might be bad, but verifing timing (pulling hoses and > > blocking/ chk timing) all are alright (car does not rev up and dwn when > > I do this). But once I put the hoses back same thing. If I pull the > > hose closest to the front end of the car, the engine stops rev'ing up > > and dwn. Another thing I did is replacing the all hoses to vacuum adv, > > I disconnected the power plug to the vacuum control module (left > > portion of firewall) and the car stops rev'ing up and down. > > SUGGESTIONS???? I agree with the above suggestion to bleed the coolant. The most common problem associated with the idle cycling up and down is usually due to a lack of coolant flowing through the cold start valve. The valve is item number 8 in this diagram http://tinyurl.com/xj18. If the valve doesn't warm up as the engine warms up (from coolant flowing through the bottom part), the PGMFI system will misinterpret the condition and idle cycling results. The first thing to due is to check the valve and make sure that the lower part of the valve gets hot as the engine warms up. If the valve doesn't get hot, try bleeding the coolant and make sure that coolant is flowing through the valve. You can double check the valve as a source of the cycling by removing the two screws from the top along with the oval shaped plate and push down on the inner valve/plunger in the center. The cycling should stop if the valve is the problem. If the valve is getting hot and pushing the inner plunger down stops the cycling, then the valve likely needs to be replaced. Eric |
Re: 1988 Honda Accord Lxi rev'ing Up and Down
Indian Summer wrote:
> > Best I can think of: turn the heat to max and bleed coolant. Remove the > battery for a minute to reset ECU. > > > My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and > > down after warming up. I thought maybe the vacuum adv. on the > > distributor might be bad, but verifing timing (pulling hoses and > > blocking/ chk timing) all are alright (car does not rev up and dwn when > > I do this). But once I put the hoses back same thing. If I pull the > > hose closest to the front end of the car, the engine stops rev'ing up > > and dwn. Another thing I did is replacing the all hoses to vacuum adv, > > I disconnected the power plug to the vacuum control module (left > > portion of firewall) and the car stops rev'ing up and down. > > SUGGESTIONS???? I agree with the above suggestion to bleed the coolant. The most common problem associated with the idle cycling up and down is usually due to a lack of coolant flowing through the cold start valve. The valve is item number 8 in this diagram http://tinyurl.com/xj18. If the valve doesn't warm up as the engine warms up (from coolant flowing through the bottom part), the PGMFI system will misinterpret the condition and idle cycling results. The first thing to due is to check the valve and make sure that the lower part of the valve gets hot as the engine warms up. If the valve doesn't get hot, try bleeding the coolant and make sure that coolant is flowing through the valve. You can double check the valve as a source of the cycling by removing the two screws from the top along with the oval shaped plate and push down on the inner valve/plunger in the center. The cycling should stop if the valve is the problem. If the valve is getting hot and pushing the inner plunger down stops the cycling, then the valve likely needs to be replaced. Eric |
Re: 1988 Honda Accord Lxi rev'ing Up and Down
Indian Summer wrote:
> > Best I can think of: turn the heat to max and bleed coolant. Remove the > battery for a minute to reset ECU. > > > My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and > > down after warming up. I thought maybe the vacuum adv. on the > > distributor might be bad, but verifing timing (pulling hoses and > > blocking/ chk timing) all are alright (car does not rev up and dwn when > > I do this). But once I put the hoses back same thing. If I pull the > > hose closest to the front end of the car, the engine stops rev'ing up > > and dwn. Another thing I did is replacing the all hoses to vacuum adv, > > I disconnected the power plug to the vacuum control module (left > > portion of firewall) and the car stops rev'ing up and down. > > SUGGESTIONS???? I agree with the above suggestion to bleed the coolant. The most common problem associated with the idle cycling up and down is usually due to a lack of coolant flowing through the cold start valve. The valve is item number 8 in this diagram http://tinyurl.com/xj18. If the valve doesn't warm up as the engine warms up (from coolant flowing through the bottom part), the PGMFI system will misinterpret the condition and idle cycling results. The first thing to due is to check the valve and make sure that the lower part of the valve gets hot as the engine warms up. If the valve doesn't get hot, try bleeding the coolant and make sure that coolant is flowing through the valve. You can double check the valve as a source of the cycling by removing the two screws from the top along with the oval shaped plate and push down on the inner valve/plunger in the center. The cycling should stop if the valve is the problem. If the valve is getting hot and pushing the inner plunger down stops the cycling, then the valve likely needs to be replaced. Eric |
Re: 1988 Honda Accord Lxi rev'ing Up and Down
Indian Summer,
To clarify, I think you mean to bleed the AIR that's trapped in the cooling system (at the provided nipple) rather than DRAIN the coolant. Some folks wouldn't know that there is a difference. 'Curly' ------------------------------ Indian Summer wrote: > Best I can think of: turn the heat to max and bleed coolant. Remove the > battery for a minute to reset ECU. > > >>My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and down >>after warming up. I thought maybe the vacuum adv. on the distributor >>might be bad, but verifing timing (pulling hoses and blocking/ chk >>timing) all are alright (car does not rev up and dwn when I do this). >>But once I put the hoses back same thing. If I pull the hose closest to >>the front end of the car, the engine stops rev'ing up and dwn. Another >>thing I did is replacing the all hoses to vacuum adv, I disconnected the >>power plug to the vacuum control module (left portion of firewall) and the >>car stops rev'ing up and down. SUGGESTIONS???? > |
Re: 1988 Honda Accord Lxi rev'ing Up and Down
Indian Summer,
To clarify, I think you mean to bleed the AIR that's trapped in the cooling system (at the provided nipple) rather than DRAIN the coolant. Some folks wouldn't know that there is a difference. 'Curly' ------------------------------ Indian Summer wrote: > Best I can think of: turn the heat to max and bleed coolant. Remove the > battery for a minute to reset ECU. > > >>My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and down >>after warming up. I thought maybe the vacuum adv. on the distributor >>might be bad, but verifing timing (pulling hoses and blocking/ chk >>timing) all are alright (car does not rev up and dwn when I do this). >>But once I put the hoses back same thing. If I pull the hose closest to >>the front end of the car, the engine stops rev'ing up and dwn. Another >>thing I did is replacing the all hoses to vacuum adv, I disconnected the >>power plug to the vacuum control module (left portion of firewall) and the >>car stops rev'ing up and down. SUGGESTIONS???? > |
All times are GMT -4. The time now is 06:52 PM. |
© 2024 MH Sub I, LLC dba Internet Brands