GTcarz - Automotive forums for cars & trucks.

GTcarz - Automotive forums for cars & trucks. (https://www.gtcarz.com/)
-   Honda Mailing List (https://www.gtcarz.com/honda-mailing-list-327/)
-   -   '92 Accord won't start at all (https://www.gtcarz.com/honda-mailing-list-327/92-accord-wont-start-all-277487/)

pjs7 02-09-2004 09:59 PM

'92 Accord won't start at all
 

Recently the radiator hose in my '92 Honda Accord busted, showering th
engine. I had the car towed and the radiator hose replaced. Now i
won't start. I put in a new battery, just to make sure it's enoug
juce. I tested for spark; there was none. I replaced the ignitio
coil; still no spark on cranking. There also is no spark from the coi
wire when held about a quarter inch from ground. There is voltage o
the two center connectors of the ignitor. I tried to test the EC
connector on the ignitor (without removing the wire) by putting an LE
(with 650 Ohms in series) between that contact and the plus of th
battery. On cranking I think it first blinked a few times and then i
stopped blinking. Did I mess up the ECU by doing that? The plasti
covers on the ignitor connectors appear to be brittle, like they took
lot of heat. What should I do next? Replace the ignitor? Can I do
test to check the ECU? How do I obtain trouble codes from the ECU (
see comments about bridging two wires, but I don't know where the
are.)
When I turn the ignition key, one step before the cranking position,
hear what appears to be the fuel pump relay for a few seconds. Ye
when I check the spark plugs after cranking, they appear quite dry. I
that as it should be?

Any help is much appreciated

-
pjs
-----------------------------------------------------------------------
Posted via RealCarAudio.com - The checkmate of the caraudio community
http://www.RealCarAudio.co
pjs7's Profile: http://www.realcaraudio.com/forums/m...nfo&userid=391
View this thread: http://www.realcaraudio.com/forums/s...?threadid=4638


'Curly Q. Links' 02-09-2004 11:04 PM

Re: '92 Accord won't start at all
 
pjs7 wrote:
>
> Recently the radiator hose in my '92 Honda Accord busted, showering the
> engine. I had the car towed and the radiator hose replaced. Now it
> won't start. I put in a new battery, just to make sure it's enough
> juce. I tested for spark; there was none. I replaced the ignition
> coil; still no spark on cranking. There also is no spark from the coil
> wire when held about a quarter inch from ground. There is voltage on
> the two center connectors of the ignitor. I tried to test the ECU
> connector on the ignitor (without removing the wire) by putting an LED
> (with 650 Ohms in series) between that contact and the plus of the
> battery. On cranking I think it first blinked a few times and then it
> stopped blinking. Did I mess up the ECU by doing that? The plastic
> covers on the ignitor connectors appear to be brittle, like they took a
> lot of heat. What should I do next? Replace the ignitor? Can I do a
> test to check the ECU? How do I obtain trouble codes from the ECU (I
> see comments about bridging two wires, but I don't know where they
> are.)
> When I turn the ignition key, one step before the cranking position, I
> hear what appears to be the fuel pump relay for a few seconds. Yet
> when I check the spark plugs after cranking, they appear quite dry. Is
> that as it should be?
>
> Any help is much appreciated.
>
> --
> pjs7

==================

pjs7,

Remove the distributor cap and make sure the rotor is turning when you
crank the engine. It is driven by cam, which is driven by the timing
belt :-(

Report back to group.

'Curly'

'Curly Q. Links' 02-09-2004 11:04 PM

Re: '92 Accord won't start at all
 
pjs7 wrote:
>
> Recently the radiator hose in my '92 Honda Accord busted, showering the
> engine. I had the car towed and the radiator hose replaced. Now it
> won't start. I put in a new battery, just to make sure it's enough
> juce. I tested for spark; there was none. I replaced the ignition
> coil; still no spark on cranking. There also is no spark from the coil
> wire when held about a quarter inch from ground. There is voltage on
> the two center connectors of the ignitor. I tried to test the ECU
> connector on the ignitor (without removing the wire) by putting an LED
> (with 650 Ohms in series) between that contact and the plus of the
> battery. On cranking I think it first blinked a few times and then it
> stopped blinking. Did I mess up the ECU by doing that? The plastic
> covers on the ignitor connectors appear to be brittle, like they took a
> lot of heat. What should I do next? Replace the ignitor? Can I do a
> test to check the ECU? How do I obtain trouble codes from the ECU (I
> see comments about bridging two wires, but I don't know where they
> are.)
> When I turn the ignition key, one step before the cranking position, I
> hear what appears to be the fuel pump relay for a few seconds. Yet
> when I check the spark plugs after cranking, they appear quite dry. Is
> that as it should be?
>
> Any help is much appreciated.
>
> --
> pjs7

==================

pjs7,

Remove the distributor cap and make sure the rotor is turning when you
crank the engine. It is driven by cam, which is driven by the timing
belt :-(

Report back to group.

'Curly'

'Curly Q. Links' 02-09-2004 11:04 PM

Re: '92 Accord won't start at all
 
pjs7 wrote:
>
> Recently the radiator hose in my '92 Honda Accord busted, showering the
> engine. I had the car towed and the radiator hose replaced. Now it
> won't start. I put in a new battery, just to make sure it's enough
> juce. I tested for spark; there was none. I replaced the ignition
> coil; still no spark on cranking. There also is no spark from the coil
> wire when held about a quarter inch from ground. There is voltage on
> the two center connectors of the ignitor. I tried to test the ECU
> connector on the ignitor (without removing the wire) by putting an LED
> (with 650 Ohms in series) between that contact and the plus of the
> battery. On cranking I think it first blinked a few times and then it
> stopped blinking. Did I mess up the ECU by doing that? The plastic
> covers on the ignitor connectors appear to be brittle, like they took a
> lot of heat. What should I do next? Replace the ignitor? Can I do a
> test to check the ECU? How do I obtain trouble codes from the ECU (I
> see comments about bridging two wires, but I don't know where they
> are.)
> When I turn the ignition key, one step before the cranking position, I
> hear what appears to be the fuel pump relay for a few seconds. Yet
> when I check the spark plugs after cranking, they appear quite dry. Is
> that as it should be?
>
> Any help is much appreciated.
>
> --
> pjs7

==================

pjs7,

Remove the distributor cap and make sure the rotor is turning when you
crank the engine. It is driven by cam, which is driven by the timing
belt :-(

Report back to group.

'Curly'

'Curly Q. Links' 02-09-2004 11:04 PM

Re: '92 Accord won't start at all
 
pjs7 wrote:
>
> Recently the radiator hose in my '92 Honda Accord busted, showering the
> engine. I had the car towed and the radiator hose replaced. Now it
> won't start. I put in a new battery, just to make sure it's enough
> juce. I tested for spark; there was none. I replaced the ignition
> coil; still no spark on cranking. There also is no spark from the coil
> wire when held about a quarter inch from ground. There is voltage on
> the two center connectors of the ignitor. I tried to test the ECU
> connector on the ignitor (without removing the wire) by putting an LED
> (with 650 Ohms in series) between that contact and the plus of the
> battery. On cranking I think it first blinked a few times and then it
> stopped blinking. Did I mess up the ECU by doing that? The plastic
> covers on the ignitor connectors appear to be brittle, like they took a
> lot of heat. What should I do next? Replace the ignitor? Can I do a
> test to check the ECU? How do I obtain trouble codes from the ECU (I
> see comments about bridging two wires, but I don't know where they
> are.)
> When I turn the ignition key, one step before the cranking position, I
> hear what appears to be the fuel pump relay for a few seconds. Yet
> when I check the spark plugs after cranking, they appear quite dry. Is
> that as it should be?
>
> Any help is much appreciated.
>
> --
> pjs7

==================

pjs7,

Remove the distributor cap and make sure the rotor is turning when you
crank the engine. It is driven by cam, which is driven by the timing
belt :-(

Report back to group.

'Curly'

pjs7 02-10-2004 02:15 AM

Re: '92 Accord won't start at all
 

Thanks, Curly.

Yes, the rotor is turning.

Since the problem started right after the busted radiator hose, I a
wondering whether that (the flood of water) might have anything to d
with it. BTW, I checked all fuses, they are all good

-
pjs
-----------------------------------------------------------------------
Posted via RealCarAudio.com - The checkmate of the caraudio community
http://www.RealCarAudio.co
pjs7's Profile: http://www.realcaraudio.com/forums/m...nfo&userid=391
View this thread: http://www.realcaraudio.com/forums/s...?threadid=4638


pjs7 02-10-2004 02:15 AM

Re: '92 Accord won't start at all
 

Thanks, Curly.

Yes, the rotor is turning.

Since the problem started right after the busted radiator hose, I a
wondering whether that (the flood of water) might have anything to d
with it. BTW, I checked all fuses, they are all good

-
pjs
-----------------------------------------------------------------------
Posted via RealCarAudio.com - The checkmate of the caraudio community
http://www.RealCarAudio.co
pjs7's Profile: http://www.realcaraudio.com/forums/m...nfo&userid=391
View this thread: http://www.realcaraudio.com/forums/s...?threadid=4638


pjs7 02-10-2004 02:15 AM

Re: '92 Accord won't start at all
 

Thanks, Curly.

Yes, the rotor is turning.

Since the problem started right after the busted radiator hose, I a
wondering whether that (the flood of water) might have anything to d
with it. BTW, I checked all fuses, they are all good

-
pjs
-----------------------------------------------------------------------
Posted via RealCarAudio.com - The checkmate of the caraudio community
http://www.RealCarAudio.co
pjs7's Profile: http://www.realcaraudio.com/forums/m...nfo&userid=391
View this thread: http://www.realcaraudio.com/forums/s...?threadid=4638


pjs7 02-10-2004 02:15 AM

Re: '92 Accord won't start at all
 

Thanks, Curly.

Yes, the rotor is turning.

Since the problem started right after the busted radiator hose, I a
wondering whether that (the flood of water) might have anything to d
with it. BTW, I checked all fuses, they are all good

-
pjs
-----------------------------------------------------------------------
Posted via RealCarAudio.com - The checkmate of the caraudio community
http://www.RealCarAudio.co
pjs7's Profile: http://www.realcaraudio.com/forums/m...nfo&userid=391
View this thread: http://www.realcaraudio.com/forums/s...?threadid=4638


Charlie S 02-10-2004 02:49 AM

Re: '92 Accord won't start at all
 
This may sound off the wall.......in the old days after we washed the
engine we ran the engine to dry off all the electrical items.

I suggest you use a hair dryer on their exterior to heat up and dry
the inside the electrical components where water could have entered.

Assuming your wife will let you use her hair dryer, if it works, it's
a cheep fix.

On Tue, 10 Feb 2004 07:15:12 GMT, pjs7 <pjs7.11efuy@realcaraudio.com>
wrote:

>
>Thanks, Curly.
>
>Yes, the rotor is turning.
>
>Since the problem started right after the busted radiator hose, I am
>wondering whether that (the flood of water) might have anything to do
>with it. BTW, I checked all fuses, they are all good.



Charlie S 02-10-2004 02:49 AM

Re: '92 Accord won't start at all
 
This may sound off the wall.......in the old days after we washed the
engine we ran the engine to dry off all the electrical items.

I suggest you use a hair dryer on their exterior to heat up and dry
the inside the electrical components where water could have entered.

Assuming your wife will let you use her hair dryer, if it works, it's
a cheep fix.

On Tue, 10 Feb 2004 07:15:12 GMT, pjs7 <pjs7.11efuy@realcaraudio.com>
wrote:

>
>Thanks, Curly.
>
>Yes, the rotor is turning.
>
>Since the problem started right after the busted radiator hose, I am
>wondering whether that (the flood of water) might have anything to do
>with it. BTW, I checked all fuses, they are all good.



Charlie S 02-10-2004 02:49 AM

Re: '92 Accord won't start at all
 
This may sound off the wall.......in the old days after we washed the
engine we ran the engine to dry off all the electrical items.

I suggest you use a hair dryer on their exterior to heat up and dry
the inside the electrical components where water could have entered.

Assuming your wife will let you use her hair dryer, if it works, it's
a cheep fix.

On Tue, 10 Feb 2004 07:15:12 GMT, pjs7 <pjs7.11efuy@realcaraudio.com>
wrote:

>
>Thanks, Curly.
>
>Yes, the rotor is turning.
>
>Since the problem started right after the busted radiator hose, I am
>wondering whether that (the flood of water) might have anything to do
>with it. BTW, I checked all fuses, they are all good.



Charlie S 02-10-2004 02:49 AM

Re: '92 Accord won't start at all
 
This may sound off the wall.......in the old days after we washed the
engine we ran the engine to dry off all the electrical items.

I suggest you use a hair dryer on their exterior to heat up and dry
the inside the electrical components where water could have entered.

Assuming your wife will let you use her hair dryer, if it works, it's
a cheep fix.

On Tue, 10 Feb 2004 07:15:12 GMT, pjs7 <pjs7.11efuy@realcaraudio.com>
wrote:

>
>Thanks, Curly.
>
>Yes, the rotor is turning.
>
>Since the problem started right after the busted radiator hose, I am
>wondering whether that (the flood of water) might have anything to do
>with it. BTW, I checked all fuses, they are all good.



T. Nelson 02-10-2004 02:15 PM

Re: '92 Accord won't start at all
 
In article <3j2h201rj8i48s37dqc99l8teqlvd3so8d@4ax.com>, Charlie S
<chasa@rcn.com> wrote:

> This may sound off the wall.......in the old days after we washed the
> engine we ran the engine to dry off all the electrical items.
>
> I suggest you use a hair dryer on their exterior to heat up and dry
> the inside the electrical components where water could have entered.
>
> Assuming your wife will let you use her hair dryer, if it works, it's
> a cheep fix.
>
> On Tue, 10 Feb 2004 07:15:12 GMT, pjs7 <pjs7.11efuy@realcaraudio.com>
> wrote:
>
> >
> >Thanks, Curly.
> >
> >Yes, the rotor is turning.
> >
> >Since the problem started right after the busted radiator hose, I am
> >wondering whether that (the flood of water) might have anything to do
> >with it. BTW, I checked all fuses, they are all good.


Great idea--excellent post--keep up the great work.
I don't know where the air cleaner is located on a 92 Accord--check it and
make sure it is dry. A vehicle won't start if the air cleaner is saturated
with water. I learned this valuable lesson after washing a motorcycle. I
was not aware that the cover on the air cleaner allowed water to flow into
the air cleaner. Also, you might want open the distributer and dry off
everything.

T. Nelson 02-10-2004 02:15 PM

Re: '92 Accord won't start at all
 
In article <3j2h201rj8i48s37dqc99l8teqlvd3so8d@4ax.com>, Charlie S
<chasa@rcn.com> wrote:

> This may sound off the wall.......in the old days after we washed the
> engine we ran the engine to dry off all the electrical items.
>
> I suggest you use a hair dryer on their exterior to heat up and dry
> the inside the electrical components where water could have entered.
>
> Assuming your wife will let you use her hair dryer, if it works, it's
> a cheep fix.
>
> On Tue, 10 Feb 2004 07:15:12 GMT, pjs7 <pjs7.11efuy@realcaraudio.com>
> wrote:
>
> >
> >Thanks, Curly.
> >
> >Yes, the rotor is turning.
> >
> >Since the problem started right after the busted radiator hose, I am
> >wondering whether that (the flood of water) might have anything to do
> >with it. BTW, I checked all fuses, they are all good.


Great idea--excellent post--keep up the great work.
I don't know where the air cleaner is located on a 92 Accord--check it and
make sure it is dry. A vehicle won't start if the air cleaner is saturated
with water. I learned this valuable lesson after washing a motorcycle. I
was not aware that the cover on the air cleaner allowed water to flow into
the air cleaner. Also, you might want open the distributer and dry off
everything.


All times are GMT -4. The time now is 12:19 PM.


© 2024 MH Sub I, LLC dba Internet Brands

Page generated in 0.12472 seconds with 5 queries