Re: 98 accord front rotor removal?
 

Is there a way to tell if they are press fit?

Steve



"loewent via CarKB.com" <u10197@uwe> wrote in message
news:68e341c4c4c3d@uwe...
> use an impact screwdriver, the prescribed tool from honda. You hit the
end
> of it with a hammer, and it presses into the head of the screw while
turning
> it out. Works great for lots of different applications. Got mine for $10
at
> a surplus hardware store...
>
> Some accords rotors are pressed on though. This I would take to the shop.
I
> have seen the shop use a special tool that machines the rotors while they
are
> still on the car, so they must think removal is a pain in the ass too...
>
> t
>
> comcastss news groups wrote:
> >> no. it's two screws for the disk and two bolts for the caliper. can't
> >> get much easier.
> >
> >That's encouraging!
> >
> >Steve
>
> --
> Message posted via http://www.carkb.com
>

Re: 98 accord front rotor removal?
 

Is there a way to tell if they are press fit?

Steve



"loewent via CarKB.com" <u10197@uwe> wrote in message
news:68e341c4c4c3d@uwe...
> use an impact screwdriver, the prescribed tool from honda. You hit the
end
> of it with a hammer, and it presses into the head of the screw while
turning
> it out. Works great for lots of different applications. Got mine for $10
at
> a surplus hardware store...
>
> Some accords rotors are pressed on though. This I would take to the shop.
I
> have seen the shop use a special tool that machines the rotors while they
are
> still on the car, so they must think removal is a pain in the ass too...
>
> t
>
> comcastss news groups wrote:
> >> no. it's two screws for the disk and two bolts for the caliper. can't
> >> get much easier.
> >
> >That's encouraging!
> >
> >Steve
>
> --
> Message posted via http://www.carkb.com
>

Re: 98 accord front rotor removal?
 

"comcastss news groups" <srivet@starprintingcorp.com> wrote in
news:YrmdnTcJNJjIwtLYnZ2dnUVZ_ridnZ2d@conversent.n et:

> Is there a way to tell if they are press fit?
>
> Steve
>
>

No screws?? just a wild guess.


--
Jim Yanik
jyanik
at
kua.net

Re: 98 accord front rotor removal?
 

"comcastss news groups" <srivet@starprintingcorp.com> wrote in
news:YrmdnTcJNJjIwtLYnZ2dnUVZ_ridnZ2d@conversent.n et:

> Is there a way to tell if they are press fit?
>
> Steve
>
>

No screws?? just a wild guess.


--
Jim Yanik
jyanik
at
kua.net

Re: 98 accord front rotor removal?
 

"comcastss news groups" <srivet@starprintingcorp.com> wrote in
news:YrmdnTcJNJjIwtLYnZ2dnUVZ_ridnZ2d@conversent.n et:

> Is there a way to tell if they are press fit?
>
> Steve
>
>

No screws?? just a wild guess.


--
Jim Yanik
jyanik
at
kua.net

Re: 98 accord front rotor removal?
 

"comcastss news groups" <srivet@starprintingcorp.com> wrote in
news:YrmdnTcJNJjIwtLYnZ2dnUVZ_ridnZ2d@conversent.n et:

> Is there a way to tell if they are press fit?
>
> Steve
>
>

No screws?? just a wild guess.


--
Jim Yanik
jyanik
at
kua.net

Re: 98 accord front rotor removal?
 

comcastss news groups wrote:
> Is there a way to tell if they are press fit?
>
> Steve


----------------------------------------

Look at your diagrams at www.slhondaparts.com

You'll see if the two screws are there. If so, buy an impact driver and
have at her.

'Curly'

Re: 98 accord front rotor removal?
 

comcastss news groups wrote:
> Is there a way to tell if they are press fit?
>
> Steve


----------------------------------------

Look at your diagrams at www.slhondaparts.com

You'll see if the two screws are there. If so, buy an impact driver and
have at her.

'Curly'

Re: 98 accord front rotor removal?
 

comcastss news groups wrote:
> Is there a way to tell if they are press fit?
>
> Steve


----------------------------------------

Look at your diagrams at www.slhondaparts.com

You'll see if the two screws are there. If so, buy an impact driver and
have at her.

'Curly'

Re: 98 accord front rotor removal?
 

comcastss news groups wrote:
> Is there a way to tell if they are press fit?
>
> Steve


----------------------------------------

Look at your diagrams at www.slhondaparts.com

You'll see if the two screws are there. If so, buy an impact driver and
have at her.

'Curly'

Re: 98 accord front rotor removal?
 

"motsco_" <motsco_@interbaun.com> wrote in message
news:454F6571.3050100@interbaun.com...
> comcastss news groups wrote:
>> Is there a way to tell if they are press fit?
>>
>> Steve
>
>
> ----------------------------------------
>
> Look at your diagrams at www.slhondaparts.com
>
> You'll see if the two screws are there. If so, buy an impact driver and
> have at her.
>
> 'Curly'

For example, if yours is an EX 4 dr, it is probably this:
http://tinyurl.com/ykngz2
That is what you want (the screws are part #28)

My daughter's '93 Accord LX 4 cylinder is shown in http://tinyurl.com/yaz42d
Notice the disc is flat and is *behind* the hub. Changing it is a big hairy
deal - I've done each side of hers once. The disc is held by the 12-point
bolts (part # 23).

BTW, if my memory hasn't faded too much the screw heads are #3 Phillips; a
#2 Phillips head will just strip them out. A test fit before taking a whack
will save you minor grief.

Mike

Re: 98 accord front rotor removal?
 

"motsco_" <motsco_@interbaun.com> wrote in message
news:454F6571.3050100@interbaun.com...
> comcastss news groups wrote:
>> Is there a way to tell if they are press fit?
>>
>> Steve
>
>
> ----------------------------------------
>
> Look at your diagrams at www.slhondaparts.com
>
> You'll see if the two screws are there. If so, buy an impact driver and
> have at her.
>
> 'Curly'

For example, if yours is an EX 4 dr, it is probably this:
http://tinyurl.com/ykngz2
That is what you want (the screws are part #28)

My daughter's '93 Accord LX 4 cylinder is shown in http://tinyurl.com/yaz42d
Notice the disc is flat and is *behind* the hub. Changing it is a big hairy
deal - I've done each side of hers once. The disc is held by the 12-point
bolts (part # 23).

BTW, if my memory hasn't faded too much the screw heads are #3 Phillips; a
#2 Phillips head will just strip them out. A test fit before taking a whack
will save you minor grief.

Mike

Re: 98 accord front rotor removal?
 

"motsco_" <motsco_@interbaun.com> wrote in message
news:454F6571.3050100@interbaun.com...
> comcastss news groups wrote:
>> Is there a way to tell if they are press fit?
>>
>> Steve
>
>
> ----------------------------------------
>
> Look at your diagrams at www.slhondaparts.com
>
> You'll see if the two screws are there. If so, buy an impact driver and
> have at her.
>
> 'Curly'

For example, if yours is an EX 4 dr, it is probably this:
http://tinyurl.com/ykngz2
That is what you want (the screws are part #28)

My daughter's '93 Accord LX 4 cylinder is shown in http://tinyurl.com/yaz42d
Notice the disc is flat and is *behind* the hub. Changing it is a big hairy
deal - I've done each side of hers once. The disc is held by the 12-point
bolts (part # 23).

BTW, if my memory hasn't faded too much the screw heads are #3 Phillips; a
#2 Phillips head will just strip them out. A test fit before taking a whack
will save you minor grief.

Mike

Re: 98 accord front rotor removal?
 

"motsco_" <motsco_@interbaun.com> wrote in message
news:454F6571.3050100@interbaun.com...
> comcastss news groups wrote:
>> Is there a way to tell if they are press fit?
>>
>> Steve
>
>
> ----------------------------------------
>
> Look at your diagrams at www.slhondaparts.com
>
> You'll see if the two screws are there. If so, buy an impact driver and
> have at her.
>
> 'Curly'

For example, if yours is an EX 4 dr, it is probably this:
http://tinyurl.com/ykngz2
That is what you want (the screws are part #28)

My daughter's '93 Accord LX 4 cylinder is shown in http://tinyurl.com/yaz42d
Notice the disc is flat and is *behind* the hub. Changing it is a big hairy
deal - I've done each side of hers once. The disc is held by the 12-point
bolts (part # 23).

BTW, if my memory hasn't faded too much the screw heads are #3 Phillips; a
#2 Phillips head will just strip them out. A test fit before taking a whack
will save you minor grief.

Mike

Re: 98 accord front rotor removal?
 

loewent via CarKB.com wrote:
> use an impact screwdriver, the prescribed tool from honda. You hit the end
> of it with a hammer, and it presses into the head of the screw while turning
> it out. Works great for lots of different applications. Got mine for $10 at
> a surplus hardware store...
>
> Some accords rotors are pressed on though.

only the old ones. this is a 98.

> This I would take to the shop. I
> have seen the shop use a special tool that machines the rotors while they are
> still on the car, so they must think removal is a pain in the ass too...

yeah, but these rotors don't "warp"*. honda was not entirely stupid
with this configuration, albeit a pita to service /if/ the disk needs to
be replaced.

* warping is a wheel/lug nut torque issue. if the disk is behind the
hub, the way the wheel sits can be messed up but it won't affect the way
the disk sits, unlike with the current system.

>
> t
>
> comcastss news groups wrote:
>>> no. it's two screws for the disk and two bolts for the caliper. can't
>>> get much easier.
>> That's encouraging!
>>
>> Steve
>