Re: Update Re: Bushing Press (Portable & Home-made) Input Sought
"Michael Pardee" <michaeltnull@cybertrails.com> wrote > "Elle" <honda.lioness@spamno.earthlink.net> wrote >> "Elle" <honda.lioness@spamno.earthlink.net> wrote >>> I've started some photos and hopefully will put this up >>> at my web site soon. >> >> http://home.earthlink.net/~honda.lioness/id15.html >> > Thanks for the link, Elle... I've bookmarked it in hopes > I'll never need it ;-} I watched a neighbor remove a > bushing with an air chisel (using a blunt chisel as a > hammer) after I failed to budge it with a Snap-on U-joint > press, so I'm hoping that would work. Your procedure looks > more labor intensive but more certain. At least one person posted in one of the auto newsgroups about how he used an air chisel to chase the bushing out. I don't know. Clamping the control arm into a vise tight enough to take the blows of an air chisel, and then not damaging the control arm itself, looks tricky and, uh, not as safe, as my approach. He-men maybe will be fine with it. I don't qualify. > I understand how exhausting jobs like that are. I salute > your persistence! Once I had the methodology down, it really wasn't bad at all. I traded muscle for time but, as you suggest, in a predictable way. Plus, one knows just about exactly where one is during each step, as far as actually getting the bushing out. Not so with an air hammer. I will say that the cost of the sockets can easily exceed the cost of a propane torch. That 1 3/4-inch socket I used should cost upwards of $20 at Sears, IIRC. I got mine at a pawn shop for $8. OTOH, I think it's a lot less expensive (dollars wise and quite possibly time-wise) than paying a shop to press out the bushings. Whether one can press the bushings back in without a torch or serious press remains open to conjecture. |
Re: Update Re: Bushing Press (Portable & Home-made) Input Sought
"Michael Pardee" <michaeltnull@cybertrails.com> wrote > "Elle" <honda.lioness@spamno.earthlink.net> wrote >> "Elle" <honda.lioness@spamno.earthlink.net> wrote >>> I've started some photos and hopefully will put this up >>> at my web site soon. >> >> http://home.earthlink.net/~honda.lioness/id15.html >> > Thanks for the link, Elle... I've bookmarked it in hopes > I'll never need it ;-} I watched a neighbor remove a > bushing with an air chisel (using a blunt chisel as a > hammer) after I failed to budge it with a Snap-on U-joint > press, so I'm hoping that would work. Your procedure looks > more labor intensive but more certain. At least one person posted in one of the auto newsgroups about how he used an air chisel to chase the bushing out. I don't know. Clamping the control arm into a vise tight enough to take the blows of an air chisel, and then not damaging the control arm itself, looks tricky and, uh, not as safe, as my approach. He-men maybe will be fine with it. I don't qualify. > I understand how exhausting jobs like that are. I salute > your persistence! Once I had the methodology down, it really wasn't bad at all. I traded muscle for time but, as you suggest, in a predictable way. Plus, one knows just about exactly where one is during each step, as far as actually getting the bushing out. Not so with an air hammer. I will say that the cost of the sockets can easily exceed the cost of a propane torch. That 1 3/4-inch socket I used should cost upwards of $20 at Sears, IIRC. I got mine at a pawn shop for $8. OTOH, I think it's a lot less expensive (dollars wise and quite possibly time-wise) than paying a shop to press out the bushings. Whether one can press the bushings back in without a torch or serious press remains open to conjecture. |
Re: Update Re: Bushing Press (Portable & Home-made) Input Sought
The vibration will often do what a press can't. I have also used them to
remove wheel bearings that are pressed in; and often if the race is stuck on a shaft, catch the edge with a chisel and walk it off. Often times the part will come apart in 1/4 the time with a air hammer > A air chisel/hammer is a great tool; I used one last week to get an axle out of a transmission. the right front axle seal was leaking (Suzuki Grand Vitara); and the other tech ordered a new transfer case; He went to a class and handed the job over to me. The new axle and front diff assembly came in but not the rest of the case, so I told the boss let me try something. With the Air Hammer and several pry bars we slowly got the axle. The snap ring had expanded out causing the stuck axle, and 1/2 of it was still missing. I took the diff out and searched it until I found the missing piece and reassembled it using only the new axle and seal; saved the customer 900-1500 dollars. Felt good that day. -- Stephen W. Hansen ASE Certified Master Automobile Technician ASE Automobile Advanced Engine Performance ASE Undercar Specialist http://autorepair.about.com/cs/troub...l_obd_main.htm http://www.troublecodes.net/technical/ > At least one person posted in one of the auto newsgroups about how he used > an air chisel to chase the bushing out. > > |
Re: Update Re: Bushing Press (Portable & Home-made) Input Sought
The vibration will often do what a press can't. I have also used them to
remove wheel bearings that are pressed in; and often if the race is stuck on a shaft, catch the edge with a chisel and walk it off. Often times the part will come apart in 1/4 the time with a air hammer > A air chisel/hammer is a great tool; I used one last week to get an axle out of a transmission. the right front axle seal was leaking (Suzuki Grand Vitara); and the other tech ordered a new transfer case; He went to a class and handed the job over to me. The new axle and front diff assembly came in but not the rest of the case, so I told the boss let me try something. With the Air Hammer and several pry bars we slowly got the axle. The snap ring had expanded out causing the stuck axle, and 1/2 of it was still missing. I took the diff out and searched it until I found the missing piece and reassembled it using only the new axle and seal; saved the customer 900-1500 dollars. Felt good that day. -- Stephen W. Hansen ASE Certified Master Automobile Technician ASE Automobile Advanced Engine Performance ASE Undercar Specialist http://autorepair.about.com/cs/troub...l_obd_main.htm http://www.troublecodes.net/technical/ > At least one person posted in one of the auto newsgroups about how he used > an air chisel to chase the bushing out. > > |
Re: Update Re: Bushing Press (Portable & Home-made) Input Sought
The vibration will often do what a press can't. I have also used them to
remove wheel bearings that are pressed in; and often if the race is stuck on a shaft, catch the edge with a chisel and walk it off. Often times the part will come apart in 1/4 the time with a air hammer > A air chisel/hammer is a great tool; I used one last week to get an axle out of a transmission. the right front axle seal was leaking (Suzuki Grand Vitara); and the other tech ordered a new transfer case; He went to a class and handed the job over to me. The new axle and front diff assembly came in but not the rest of the case, so I told the boss let me try something. With the Air Hammer and several pry bars we slowly got the axle. The snap ring had expanded out causing the stuck axle, and 1/2 of it was still missing. I took the diff out and searched it until I found the missing piece and reassembled it using only the new axle and seal; saved the customer 900-1500 dollars. Felt good that day. -- Stephen W. Hansen ASE Certified Master Automobile Technician ASE Automobile Advanced Engine Performance ASE Undercar Specialist http://autorepair.about.com/cs/troub...l_obd_main.htm http://www.troublecodes.net/technical/ > At least one person posted in one of the auto newsgroups about how he used > an air chisel to chase the bushing out. > > |
Re: Update Re: Bushing Press (Portable & Home-made) Input Sought
"Elle" <honda.lioness@spamno.earthlink.net> wrote in message
news:Tsl8g.2351$u4.1989@newsread1.news.pas.earthli nk.net... > > "Michael Pardee" <michaeltnull@cybertrails.com> wrote >> "Elle" <honda.lioness@spamno.earthlink.net> wrote >>> "Elle" <honda.lioness@spamno.earthlink.net> wrote >>>> I've started some photos and hopefully will put this up at my web site >>>> soon. >>> >>> http://home.earthlink.net/~honda.lioness/id15.html >>> >> Thanks for the link, Elle... I've bookmarked it in hopes I'll never need >> it ;-} I watched a neighbor remove a bushing with an air chisel (using a >> blunt chisel as a hammer) after I failed to budge it with a Snap-on >> U-joint press, so I'm hoping that would work. Your procedure looks more >> labor intensive but more certain. > > At least one person posted in one of the auto newsgroups about how he used > an air chisel to chase the bushing out. > > I don't know. Clamping the control arm into a vise tight enough to take > the blows of an air chisel, and then not damaging the control arm itself, > looks tricky and, uh, not as safe, as my approach. He-men maybe will be > fine with it. I don't qualify. > It surprised me that he held the work in his left hand while using the air chisel in his right hand. I would have thought he would want to support the work on a bench, but no. But then, he was a "he-man" and I don't qualify either! When I use the air chisel I have some trouble getting it to stay put. It loves to walk once it starts chattering. Mike |
Re: Update Re: Bushing Press (Portable & Home-made) Input Sought
"Elle" <honda.lioness@spamno.earthlink.net> wrote in message
news:Tsl8g.2351$u4.1989@newsread1.news.pas.earthli nk.net... > > "Michael Pardee" <michaeltnull@cybertrails.com> wrote >> "Elle" <honda.lioness@spamno.earthlink.net> wrote >>> "Elle" <honda.lioness@spamno.earthlink.net> wrote >>>> I've started some photos and hopefully will put this up at my web site >>>> soon. >>> >>> http://home.earthlink.net/~honda.lioness/id15.html >>> >> Thanks for the link, Elle... I've bookmarked it in hopes I'll never need >> it ;-} I watched a neighbor remove a bushing with an air chisel (using a >> blunt chisel as a hammer) after I failed to budge it with a Snap-on >> U-joint press, so I'm hoping that would work. Your procedure looks more >> labor intensive but more certain. > > At least one person posted in one of the auto newsgroups about how he used > an air chisel to chase the bushing out. > > I don't know. Clamping the control arm into a vise tight enough to take > the blows of an air chisel, and then not damaging the control arm itself, > looks tricky and, uh, not as safe, as my approach. He-men maybe will be > fine with it. I don't qualify. > It surprised me that he held the work in his left hand while using the air chisel in his right hand. I would have thought he would want to support the work on a bench, but no. But then, he was a "he-man" and I don't qualify either! When I use the air chisel I have some trouble getting it to stay put. It loves to walk once it starts chattering. Mike |
Re: Update Re: Bushing Press (Portable & Home-made) Input Sought
"Elle" <honda.lioness@spamno.earthlink.net> wrote in message
news:Tsl8g.2351$u4.1989@newsread1.news.pas.earthli nk.net... > > "Michael Pardee" <michaeltnull@cybertrails.com> wrote >> "Elle" <honda.lioness@spamno.earthlink.net> wrote >>> "Elle" <honda.lioness@spamno.earthlink.net> wrote >>>> I've started some photos and hopefully will put this up at my web site >>>> soon. >>> >>> http://home.earthlink.net/~honda.lioness/id15.html >>> >> Thanks for the link, Elle... I've bookmarked it in hopes I'll never need >> it ;-} I watched a neighbor remove a bushing with an air chisel (using a >> blunt chisel as a hammer) after I failed to budge it with a Snap-on >> U-joint press, so I'm hoping that would work. Your procedure looks more >> labor intensive but more certain. > > At least one person posted in one of the auto newsgroups about how he used > an air chisel to chase the bushing out. > > I don't know. Clamping the control arm into a vise tight enough to take > the blows of an air chisel, and then not damaging the control arm itself, > looks tricky and, uh, not as safe, as my approach. He-men maybe will be > fine with it. I don't qualify. > It surprised me that he held the work in his left hand while using the air chisel in his right hand. I would have thought he would want to support the work on a bench, but no. But then, he was a "he-man" and I don't qualify either! When I use the air chisel I have some trouble getting it to stay put. It loves to walk once it starts chattering. Mike |
All times are GMT -4. The time now is 11:09 PM. |
© 2024 MH Sub I, LLC dba Internet Brands