DelSol B16A Ignition Timing out but Cam Belt Timing is correct
Can anyone help? I'm tearing, what little is left of my hair, out at
the moment. When adjusting my ignition timing by moving the distributor I am unable to line the crankshaft casing mark with the center 16degree timing mark on the pully. The distributor is rotated as far as it wil go towards the firewall. Its still a few degrees off. I have checked the cam belt timing a number of times now looking in case the belt has slipped by a tooth but it looks spot on. I have even tried adjusting cams back one tooth but the car would not start. Currently with the distributor as far towards the firewall as it will go, the car will idle fine but when driving the car has little power. It gets noticeably worse when the car is warm. Is there anything else that could cause the ignition timing to be so far out? Any sensor that could cause the ECU to advance \ retard the timing? Any help is appreciated. Graeme. |
Re: DelSol B16A Ignition Timing out but Cam Belt Timing is correct
fish wrote:
> > Can anyone help? I'm tearing, what little is left of my hair, out at > the moment. > > When adjusting my ignition timing by moving the distributor I am unable > to line the crankshaft casing mark with the center 16degree timing mark > on the pully. The distributor is rotated as far as it wil go towards > the firewall. Its still a few degrees off. > > I have checked the cam belt timing a number of times now looking in > case the belt has slipped by a tooth but it looks spot on. I have even > tried adjusting cams back one tooth but the car would not start. > > Currently with the distributor as far towards the firewall as it will > go, the car will idle fine but when driving the car has little power. > It gets noticeably worse when the car is warm. > > Is there anything else that could cause the ignition timing to be so > far out? Any sensor that could cause the ECU to advance \ retard the > timing? > > Any help is appreciated. > Graeme. ----------------------------------- What YEAR is the vehicle, and did you put the JUMPER on while setting the timing? 'Curly' |
Re: DelSol B16A Ignition Timing out but Cam Belt Timing is correct
fish wrote:
> > Can anyone help? I'm tearing, what little is left of my hair, out at > the moment. > > When adjusting my ignition timing by moving the distributor I am unable > to line the crankshaft casing mark with the center 16degree timing mark > on the pully. The distributor is rotated as far as it wil go towards > the firewall. Its still a few degrees off. > > I have checked the cam belt timing a number of times now looking in > case the belt has slipped by a tooth but it looks spot on. I have even > tried adjusting cams back one tooth but the car would not start. > > Currently with the distributor as far towards the firewall as it will > go, the car will idle fine but when driving the car has little power. > It gets noticeably worse when the car is warm. > > Is there anything else that could cause the ignition timing to be so > far out? Any sensor that could cause the ECU to advance \ retard the > timing? > > Any help is appreciated. > Graeme. ----------------------------------- What YEAR is the vehicle, and did you put the JUMPER on while setting the timing? 'Curly' |
Re: DelSol B16A Ignition Timing out but Cam Belt Timing is correct
fish wrote:
> > Can anyone help? I'm tearing, what little is left of my hair, out at > the moment. > > When adjusting my ignition timing by moving the distributor I am unable > to line the crankshaft casing mark with the center 16degree timing mark > on the pully. The distributor is rotated as far as it wil go towards > the firewall. Its still a few degrees off. > > I have checked the cam belt timing a number of times now looking in > case the belt has slipped by a tooth but it looks spot on. I have even > tried adjusting cams back one tooth but the car would not start. > > Currently with the distributor as far towards the firewall as it will > go, the car will idle fine but when driving the car has little power. > It gets noticeably worse when the car is warm. > > Is there anything else that could cause the ignition timing to be so > far out? Any sensor that could cause the ECU to advance \ retard the > timing? > > Any help is appreciated. > Graeme. ----------------------------------- What YEAR is the vehicle, and did you put the JUMPER on while setting the timing? 'Curly' |
Re: DelSol B16A Ignition Timing out but Cam Belt Timing is correct
Its a 1992 1.6 Vti
Yep, I jumpered the connector near the ECU. Didn't seem to make any difference. 'Curly Q. Links' wrote: > fish wrote: > > > > Can anyone help? I'm tearing, what little is left of my hair, out at > > the moment. > > > > When adjusting my ignition timing by moving the distributor I am unable > > to line the crankshaft casing mark with the center 16degree timing mark > > on the pully. The distributor is rotated as far as it wil go towards > > the firewall. Its still a few degrees off. > > > > I have checked the cam belt timing a number of times now looking in > > case the belt has slipped by a tooth but it looks spot on. I have even > > tried adjusting cams back one tooth but the car would not start. > > > > Currently with the distributor as far towards the firewall as it will > > go, the car will idle fine but when driving the car has little power. > > It gets noticeably worse when the car is warm. > > > > Is there anything else that could cause the ignition timing to be so > > far out? Any sensor that could cause the ECU to advance \ retard the > > timing? > > > > Any help is appreciated. > > Graeme. > ----------------------------------- > > What YEAR is the vehicle, and did you put the JUMPER on while setting > the timing? > > 'Curly' |
Re: DelSol B16A Ignition Timing out but Cam Belt Timing is correct
Its a 1992 1.6 Vti
Yep, I jumpered the connector near the ECU. Didn't seem to make any difference. 'Curly Q. Links' wrote: > fish wrote: > > > > Can anyone help? I'm tearing, what little is left of my hair, out at > > the moment. > > > > When adjusting my ignition timing by moving the distributor I am unable > > to line the crankshaft casing mark with the center 16degree timing mark > > on the pully. The distributor is rotated as far as it wil go towards > > the firewall. Its still a few degrees off. > > > > I have checked the cam belt timing a number of times now looking in > > case the belt has slipped by a tooth but it looks spot on. I have even > > tried adjusting cams back one tooth but the car would not start. > > > > Currently with the distributor as far towards the firewall as it will > > go, the car will idle fine but when driving the car has little power. > > It gets noticeably worse when the car is warm. > > > > Is there anything else that could cause the ignition timing to be so > > far out? Any sensor that could cause the ECU to advance \ retard the > > timing? > > > > Any help is appreciated. > > Graeme. > ----------------------------------- > > What YEAR is the vehicle, and did you put the JUMPER on while setting > the timing? > > 'Curly' |
Re: DelSol B16A Ignition Timing out but Cam Belt Timing is correct
Its a 1992 1.6 Vti
Yep, I jumpered the connector near the ECU. Didn't seem to make any difference. 'Curly Q. Links' wrote: > fish wrote: > > > > Can anyone help? I'm tearing, what little is left of my hair, out at > > the moment. > > > > When adjusting my ignition timing by moving the distributor I am unable > > to line the crankshaft casing mark with the center 16degree timing mark > > on the pully. The distributor is rotated as far as it wil go towards > > the firewall. Its still a few degrees off. > > > > I have checked the cam belt timing a number of times now looking in > > case the belt has slipped by a tooth but it looks spot on. I have even > > tried adjusting cams back one tooth but the car would not start. > > > > Currently with the distributor as far towards the firewall as it will > > go, the car will idle fine but when driving the car has little power. > > It gets noticeably worse when the car is warm. > > > > Is there anything else that could cause the ignition timing to be so > > far out? Any sensor that could cause the ECU to advance \ retard the > > timing? > > > > Any help is appreciated. > > Graeme. > ----------------------------------- > > What YEAR is the vehicle, and did you put the JUMPER on while setting > the timing? > > 'Curly' |
Re: DelSol B16A Ignition Timing out but Cam Belt Timing is correct
"fish" <gawinter_2000@yahoo.com> wrote in
news:1155157874.963324.270060@m73g2000cwd.googlegr oups.com: > > 'Curly Q. Links' wrote: > >> > >> > Currently with the distributor as far towards the firewall as it >> > will go, the car will idle fine but when driving the car has little >> > power. It gets noticeably worse when the car is warm. >> > >> > Is there anything else that could cause the ignition timing to be >> > so far out? Any sensor that could cause the ECU to advance \ retard >> > the timing? >> > >> >> What YEAR is the vehicle, and did you put the JUMPER on while setting >> the timing? >> > > Its a 1992 1.6 Vti > Yep, I jumpered the connector near the ECU. Didn't seem to make any > difference. Then your timing belt is off, even if it looks like it's not. -- TeGGeR® The Unofficial Honda/Acura FAQ www.tegger.com/hondafaq/ |
Re: DelSol B16A Ignition Timing out but Cam Belt Timing is correct
"fish" <gawinter_2000@yahoo.com> wrote in
news:1155157874.963324.270060@m73g2000cwd.googlegr oups.com: > > 'Curly Q. Links' wrote: > >> > >> > Currently with the distributor as far towards the firewall as it >> > will go, the car will idle fine but when driving the car has little >> > power. It gets noticeably worse when the car is warm. >> > >> > Is there anything else that could cause the ignition timing to be >> > so far out? Any sensor that could cause the ECU to advance \ retard >> > the timing? >> > >> >> What YEAR is the vehicle, and did you put the JUMPER on while setting >> the timing? >> > > Its a 1992 1.6 Vti > Yep, I jumpered the connector near the ECU. Didn't seem to make any > difference. Then your timing belt is off, even if it looks like it's not. -- TeGGeR® The Unofficial Honda/Acura FAQ www.tegger.com/hondafaq/ |
Re: DelSol B16A Ignition Timing out but Cam Belt Timing is correct
"fish" <gawinter_2000@yahoo.com> wrote in
news:1155157874.963324.270060@m73g2000cwd.googlegr oups.com: > > 'Curly Q. Links' wrote: > >> > >> > Currently with the distributor as far towards the firewall as it >> > will go, the car will idle fine but when driving the car has little >> > power. It gets noticeably worse when the car is warm. >> > >> > Is there anything else that could cause the ignition timing to be >> > so far out? Any sensor that could cause the ECU to advance \ retard >> > the timing? >> > >> >> What YEAR is the vehicle, and did you put the JUMPER on while setting >> the timing? >> > > Its a 1992 1.6 Vti > Yep, I jumpered the connector near the ECU. Didn't seem to make any > difference. Then your timing belt is off, even if it looks like it's not. -- TeGGeR® The Unofficial Honda/Acura FAQ www.tegger.com/hondafaq/ |
Re: DelSol B16A Ignition Timing out but Cam Belt Timing is correct
TeGGeR® wrote: > > > Then your timing belt is off, even if it looks like it's not. Could be.. The only other thing I could think of is maybe a sheared dist gear pin, or something like that. But being I haven't looked at the base of one of those distributors, I couldn't say if they use one. I had this happen on my ford truck one time though. The pin sheared off at the base, and the dist would "wander" and gradually shift in direction until it got to the point that I ran out of room to turn it. Yanked it out, and saw the gone pin. They had those at the autoparts, and I was back off to the races. Seems to me, if the timing marks look perfectly spot on, it should be pretty close, but I've seen weirder things happen.. MK |
Re: DelSol B16A Ignition Timing out but Cam Belt Timing is correct
TeGGeR® wrote: > > > Then your timing belt is off, even if it looks like it's not. Could be.. The only other thing I could think of is maybe a sheared dist gear pin, or something like that. But being I haven't looked at the base of one of those distributors, I couldn't say if they use one. I had this happen on my ford truck one time though. The pin sheared off at the base, and the dist would "wander" and gradually shift in direction until it got to the point that I ran out of room to turn it. Yanked it out, and saw the gone pin. They had those at the autoparts, and I was back off to the races. Seems to me, if the timing marks look perfectly spot on, it should be pretty close, but I've seen weirder things happen.. MK |
Re: DelSol B16A Ignition Timing out but Cam Belt Timing is correct
TeGGeR® wrote: > > > Then your timing belt is off, even if it looks like it's not. Could be.. The only other thing I could think of is maybe a sheared dist gear pin, or something like that. But being I haven't looked at the base of one of those distributors, I couldn't say if they use one. I had this happen on my ford truck one time though. The pin sheared off at the base, and the dist would "wander" and gradually shift in direction until it got to the point that I ran out of room to turn it. Yanked it out, and saw the gone pin. They had those at the autoparts, and I was back off to the races. Seems to me, if the timing marks look perfectly spot on, it should be pretty close, but I've seen weirder things happen.. MK |
Re: DelSol B16A Ignition Timing out but Cam Belt Timing is correct
nm5k@wt.net wrote in
news:1155199444.253717.15100@b28g2000cwb.googlegro ups.com: > > TeGGeR® wrote: > >> >> >> Then your timing belt is off, even if it looks like it's not. > > Could be.. The only other thing I could think of is maybe a > sheared dist gear pin, or something like that. But being I haven't > looked at the base of one of those distributors, I couldn't say > if they use one. I had this happen on my ford truck one time > though. The pin sheared off at the base, and the dist would > "wander" and gradually shift in direction until it got to the point > that I ran out of room to turn it. Yanked it out, and saw the > gone pin. They had those at the autoparts, and I was back > off to the races. Seems to me, if the timing marks look > perfectly spot on, it should be pretty close, but I've seen > weirder things happen.. > MK > > This isn't one of those situations. -- TeGGeR® The Unofficial Honda/Acura FAQ www.tegger.com/hondafaq/ |
Re: DelSol B16A Ignition Timing out but Cam Belt Timing is correct
nm5k@wt.net wrote in
news:1155199444.253717.15100@b28g2000cwb.googlegro ups.com: > > TeGGeR® wrote: > >> >> >> Then your timing belt is off, even if it looks like it's not. > > Could be.. The only other thing I could think of is maybe a > sheared dist gear pin, or something like that. But being I haven't > looked at the base of one of those distributors, I couldn't say > if they use one. I had this happen on my ford truck one time > though. The pin sheared off at the base, and the dist would > "wander" and gradually shift in direction until it got to the point > that I ran out of room to turn it. Yanked it out, and saw the > gone pin. They had those at the autoparts, and I was back > off to the races. Seems to me, if the timing marks look > perfectly spot on, it should be pretty close, but I've seen > weirder things happen.. > MK > > This isn't one of those situations. -- TeGGeR® The Unofficial Honda/Acura FAQ www.tegger.com/hondafaq/ |
Re: DelSol B16A Ignition Timing out but Cam Belt Timing is correct
nm5k@wt.net wrote in
news:1155199444.253717.15100@b28g2000cwb.googlegro ups.com: > > TeGGeR® wrote: > >> >> >> Then your timing belt is off, even if it looks like it's not. > > Could be.. The only other thing I could think of is maybe a > sheared dist gear pin, or something like that. But being I haven't > looked at the base of one of those distributors, I couldn't say > if they use one. I had this happen on my ford truck one time > though. The pin sheared off at the base, and the dist would > "wander" and gradually shift in direction until it got to the point > that I ran out of room to turn it. Yanked it out, and saw the > gone pin. They had those at the autoparts, and I was back > off to the races. Seems to me, if the timing marks look > perfectly spot on, it should be pretty close, but I've seen > weirder things happen.. > MK > > This isn't one of those situations. -- TeGGeR® The Unofficial Honda/Acura FAQ www.tegger.com/hondafaq/ |
Re: DelSol B16A Ignition Timing out but Cam Belt Timing is correct
nm5k@wt.net wrote:
> TeGGeR� wrote: > >> >> Then your timing belt is off, even if it looks like it's not. > > Could be.. The only other thing I could think of is maybe a > sheared dist gear pin, or something like that. highly unlikely - it has no load. only way something like that can happen is if the retainer ring somehow disappears... > But being I haven't > looked at the base of one of those distributors, I couldn't say > if they use one. I had this happen on my ford truck one time > though. The pin sheared off at the base, and the dist would > "wander" and gradually shift in direction until it got to the point > that I ran out of room to turn it. Yanked it out, and saw the > gone pin. They had those at the autoparts, and I was back > off to the races. Seems to me, if the timing marks look > perfectly spot on, it should be pretty close, but I've seen > weirder things happen.. > MK > check the belt timing. you have all the classic symptoms. |
Re: DelSol B16A Ignition Timing out but Cam Belt Timing is correct
nm5k@wt.net wrote:
> TeGGeR� wrote: > >> >> Then your timing belt is off, even if it looks like it's not. > > Could be.. The only other thing I could think of is maybe a > sheared dist gear pin, or something like that. highly unlikely - it has no load. only way something like that can happen is if the retainer ring somehow disappears... > But being I haven't > looked at the base of one of those distributors, I couldn't say > if they use one. I had this happen on my ford truck one time > though. The pin sheared off at the base, and the dist would > "wander" and gradually shift in direction until it got to the point > that I ran out of room to turn it. Yanked it out, and saw the > gone pin. They had those at the autoparts, and I was back > off to the races. Seems to me, if the timing marks look > perfectly spot on, it should be pretty close, but I've seen > weirder things happen.. > MK > check the belt timing. you have all the classic symptoms. |
Re: DelSol B16A Ignition Timing out but Cam Belt Timing is correct
nm5k@wt.net wrote:
> TeGGeR� wrote: > >> >> Then your timing belt is off, even if it looks like it's not. > > Could be.. The only other thing I could think of is maybe a > sheared dist gear pin, or something like that. highly unlikely - it has no load. only way something like that can happen is if the retainer ring somehow disappears... > But being I haven't > looked at the base of one of those distributors, I couldn't say > if they use one. I had this happen on my ford truck one time > though. The pin sheared off at the base, and the dist would > "wander" and gradually shift in direction until it got to the point > that I ran out of room to turn it. Yanked it out, and saw the > gone pin. They had those at the autoparts, and I was back > off to the races. Seems to me, if the timing marks look > perfectly spot on, it should be pretty close, but I've seen > weirder things happen.. > MK > check the belt timing. you have all the classic symptoms. |
Re: DelSol B16A Ignition Timing out but Cam Belt Timing is correct
Its actually got a brand new distributor on it.
The car had a misfire so I ordered an ignition module and a coil but got sent a whole distributor. Result! Missfire was solved, but the timing issue is the same with both dizzys. I too was convinced all the symptoms pointed towards the timing belt, but I have checked it numerous times. Everything seems to line up the arrows on the cams point upwards, the center lines line up, and the TDC mark ( white on by itself) lines up with the mark on the plastic casing. I'm no professional, so I'm going to have take it to a garage to have them check the cambelt. I was expecting something not to line up. At least by a few degrees. jim beam wrote: > nm5k@wt.net wrote: > > TeGGeR? wrote: > > > >> > >> Then your timing belt is off, even if it looks like it's not. > > > > Could be.. The only other thing I could think of is maybe a > > sheared dist gear pin, or something like that. > > highly unlikely - it has no load. only way something like that can > happen is if the retainer ring somehow disappears... > > > But being I haven't > > looked at the base of one of those distributors, I couldn't say > > if they use one. I had this happen on my ford truck one time > > though. The pin sheared off at the base, and the dist would > > "wander" and gradually shift in direction until it got to the point > > that I ran out of room to turn it. Yanked it out, and saw the > > gone pin. They had those at the autoparts, and I was back > > off to the races. Seems to me, if the timing marks look > > perfectly spot on, it should be pretty close, but I've seen > > weirder things happen.. > > MK > > > > check the belt timing. you have all the classic symptoms. |
Re: DelSol B16A Ignition Timing out but Cam Belt Timing is correct
Its actually got a brand new distributor on it.
The car had a misfire so I ordered an ignition module and a coil but got sent a whole distributor. Result! Missfire was solved, but the timing issue is the same with both dizzys. I too was convinced all the symptoms pointed towards the timing belt, but I have checked it numerous times. Everything seems to line up the arrows on the cams point upwards, the center lines line up, and the TDC mark ( white on by itself) lines up with the mark on the plastic casing. I'm no professional, so I'm going to have take it to a garage to have them check the cambelt. I was expecting something not to line up. At least by a few degrees. jim beam wrote: > nm5k@wt.net wrote: > > TeGGeR? wrote: > > > >> > >> Then your timing belt is off, even if it looks like it's not. > > > > Could be.. The only other thing I could think of is maybe a > > sheared dist gear pin, or something like that. > > highly unlikely - it has no load. only way something like that can > happen is if the retainer ring somehow disappears... > > > But being I haven't > > looked at the base of one of those distributors, I couldn't say > > if they use one. I had this happen on my ford truck one time > > though. The pin sheared off at the base, and the dist would > > "wander" and gradually shift in direction until it got to the point > > that I ran out of room to turn it. Yanked it out, and saw the > > gone pin. They had those at the autoparts, and I was back > > off to the races. Seems to me, if the timing marks look > > perfectly spot on, it should be pretty close, but I've seen > > weirder things happen.. > > MK > > > > check the belt timing. you have all the classic symptoms. |
Re: DelSol B16A Ignition Timing out but Cam Belt Timing is correct
Its actually got a brand new distributor on it.
The car had a misfire so I ordered an ignition module and a coil but got sent a whole distributor. Result! Missfire was solved, but the timing issue is the same with both dizzys. I too was convinced all the symptoms pointed towards the timing belt, but I have checked it numerous times. Everything seems to line up the arrows on the cams point upwards, the center lines line up, and the TDC mark ( white on by itself) lines up with the mark on the plastic casing. I'm no professional, so I'm going to have take it to a garage to have them check the cambelt. I was expecting something not to line up. At least by a few degrees. jim beam wrote: > nm5k@wt.net wrote: > > TeGGeR? wrote: > > > >> > >> Then your timing belt is off, even if it looks like it's not. > > > > Could be.. The only other thing I could think of is maybe a > > sheared dist gear pin, or something like that. > > highly unlikely - it has no load. only way something like that can > happen is if the retainer ring somehow disappears... > > > But being I haven't > > looked at the base of one of those distributors, I couldn't say > > if they use one. I had this happen on my ford truck one time > > though. The pin sheared off at the base, and the dist would > > "wander" and gradually shift in direction until it got to the point > > that I ran out of room to turn it. Yanked it out, and saw the > > gone pin. They had those at the autoparts, and I was back > > off to the races. Seems to me, if the timing marks look > > perfectly spot on, it should be pretty close, but I've seen > > weirder things happen.. > > MK > > > > check the belt timing. you have all the classic symptoms. |
Re: DelSol B16A Ignition Timing out but Cam Belt Timing is correct
jim beam wrote: > nm5k@wt.net wrote: > > TeGGeR? wrote: > > > >> > >> Then your timing belt is off, even if it looks like it's not. > > > > Could be.. The only other thing I could think of is maybe a > > sheared dist gear pin, or something like that. > > highly unlikely - it has no load. only way something like that can > happen is if the retainer ring somehow disappears... OK, like I say, I haven't looked at one. "honda" Just wanted to mention it in case it did have some type of lock, pin, or whatever for a gear or drive.. MK |
Re: DelSol B16A Ignition Timing out but Cam Belt Timing is correct
jim beam wrote: > nm5k@wt.net wrote: > > TeGGeR? wrote: > > > >> > >> Then your timing belt is off, even if it looks like it's not. > > > > Could be.. The only other thing I could think of is maybe a > > sheared dist gear pin, or something like that. > > highly unlikely - it has no load. only way something like that can > happen is if the retainer ring somehow disappears... OK, like I say, I haven't looked at one. "honda" Just wanted to mention it in case it did have some type of lock, pin, or whatever for a gear or drive.. MK |
Re: DelSol B16A Ignition Timing out but Cam Belt Timing is correct
jim beam wrote: > nm5k@wt.net wrote: > > TeGGeR? wrote: > > > >> > >> Then your timing belt is off, even if it looks like it's not. > > > > Could be.. The only other thing I could think of is maybe a > > sheared dist gear pin, or something like that. > > highly unlikely - it has no load. only way something like that can > happen is if the retainer ring somehow disappears... OK, like I say, I haven't looked at one. "honda" Just wanted to mention it in case it did have some type of lock, pin, or whatever for a gear or drive.. MK |
Re: DelSol B16A Ignition Timing out but Cam Belt Timing is correct
nm5k@wt.net wrote in
news:1155293103.474121.70900@i3g2000cwc.googlegrou ps.com: > > jim beam wrote: >> nm5k@wt.net wrote: >> > TeGGeR? wrote: >> > >> >> >> >> Then your timing belt is off, even if it looks like it's not. >> > >> > Could be.. The only other thing I could think of is maybe a >> > sheared dist gear pin, or something like that. >> >> highly unlikely - it has no load. only way something like that can >> happen is if the retainer ring somehow disappears... > > OK, like I say, I haven't looked at one. "honda" Just wanted to > mention it > in case it did have some type of lock, pin, or whatever for a gear or > drive.. > MK > > The distributor drive shaft keys to the camshaft with a slotted arrangement that looks a bit like a large flat-blade screwdriver. It would take quite an event to shear that. The slot and key are offset from the axial center, so the distributor can only go on one way. The timing belt, however, can very easily be off by one tooth. -- TeGGeR® The Unofficial Honda/Acura FAQ www.tegger.com/hondafaq/ |
Re: DelSol B16A Ignition Timing out but Cam Belt Timing is correct
nm5k@wt.net wrote in
news:1155293103.474121.70900@i3g2000cwc.googlegrou ps.com: > > jim beam wrote: >> nm5k@wt.net wrote: >> > TeGGeR? wrote: >> > >> >> >> >> Then your timing belt is off, even if it looks like it's not. >> > >> > Could be.. The only other thing I could think of is maybe a >> > sheared dist gear pin, or something like that. >> >> highly unlikely - it has no load. only way something like that can >> happen is if the retainer ring somehow disappears... > > OK, like I say, I haven't looked at one. "honda" Just wanted to > mention it > in case it did have some type of lock, pin, or whatever for a gear or > drive.. > MK > > The distributor drive shaft keys to the camshaft with a slotted arrangement that looks a bit like a large flat-blade screwdriver. It would take quite an event to shear that. The slot and key are offset from the axial center, so the distributor can only go on one way. The timing belt, however, can very easily be off by one tooth. -- TeGGeR® The Unofficial Honda/Acura FAQ www.tegger.com/hondafaq/ |
Re: DelSol B16A Ignition Timing out but Cam Belt Timing is correct
nm5k@wt.net wrote in
news:1155293103.474121.70900@i3g2000cwc.googlegrou ps.com: > > jim beam wrote: >> nm5k@wt.net wrote: >> > TeGGeR? wrote: >> > >> >> >> >> Then your timing belt is off, even if it looks like it's not. >> > >> > Could be.. The only other thing I could think of is maybe a >> > sheared dist gear pin, or something like that. >> >> highly unlikely - it has no load. only way something like that can >> happen is if the retainer ring somehow disappears... > > OK, like I say, I haven't looked at one. "honda" Just wanted to > mention it > in case it did have some type of lock, pin, or whatever for a gear or > drive.. > MK > > The distributor drive shaft keys to the camshaft with a slotted arrangement that looks a bit like a large flat-blade screwdriver. It would take quite an event to shear that. The slot and key are offset from the axial center, so the distributor can only go on one way. The timing belt, however, can very easily be off by one tooth. -- TeGGeR® The Unofficial Honda/Acura FAQ www.tegger.com/hondafaq/ |
Re: DelSol B16A Ignition Timing out but Cam Belt Timing is correct
When you checked the cam belt timing, did you use the timing marks on
the flywheel? (you mentioned a plastic cover with white mark). I would check to see if the vacuum advance in the distributor is binding, or stuck, or out of adjustment. |
Re: DelSol B16A Ignition Timing out but Cam Belt Timing is correct
When you checked the cam belt timing, did you use the timing marks on
the flywheel? (you mentioned a plastic cover with white mark). I would check to see if the vacuum advance in the distributor is binding, or stuck, or out of adjustment. |
Re: DelSol B16A Ignition Timing out but Cam Belt Timing is correct
When you checked the cam belt timing, did you use the timing marks on
the flywheel? (you mentioned a plastic cover with white mark). I would check to see if the vacuum advance in the distributor is binding, or stuck, or out of adjustment. |
Re: DelSol B16A Ignition Timing out but Cam Belt Timing is correct
William Burke wrote:
> When you checked the cam belt timing, did you use the timing marks on > the flywheel? (you mentioned a plastic cover with white mark). I would > check to see if the vacuum advance in the distributor is binding, or > stuck, or out of adjustment. > there is no vacuum advance on a del sol. |
Re: DelSol B16A Ignition Timing out but Cam Belt Timing is correct
William Burke wrote:
> When you checked the cam belt timing, did you use the timing marks on > the flywheel? (you mentioned a plastic cover with white mark). I would > check to see if the vacuum advance in the distributor is binding, or > stuck, or out of adjustment. > there is no vacuum advance on a del sol. |
Re: DelSol B16A Ignition Timing out but Cam Belt Timing is correct
William Burke wrote:
> When you checked the cam belt timing, did you use the timing marks on > the flywheel? (you mentioned a plastic cover with white mark). I would > check to see if the vacuum advance in the distributor is binding, or > stuck, or out of adjustment. > there is no vacuum advance on a del sol. |
Re: DelSol B16A Ignition Timing out but Cam Belt Timing is correct
fish wrote:
> Its actually got a brand new distributor on it. > The car had a misfire so I ordered an ignition module and a coil but > got sent a whole distributor. Result! > Missfire was solved, but the timing issue is the same with both dizzys. if it spans both distributors, the only thing it can be is the belt. > > I too was convinced all the symptoms pointed towards the timing belt, > but I have checked it numerous times. get the helm manual and check it in reference to that. if the belt is slack, it's easy for the pulleys to "look about right" but they're not. > > Everything seems to line up the arrows on the cams point upwards, it's set relative the head, not vertical. the head's slightly sloped. > the > center lines line up, and the TDC mark ( white on by itself) lines up > with the mark on the plastic casing. > > I'm no professional, so I'm going to have take it to a garage to have > them check the cambelt. you can do it yourself if you have the correct info! knowledge is the key. > > I was expecting something not to line up. At least by a few degrees. > > > > jim beam wrote: >> nm5k@wt.net wrote: >>> TeGGeR? wrote: >>> >>>> Then your timing belt is off, even if it looks like it's not. >>> Could be.. The only other thing I could think of is maybe a >>> sheared dist gear pin, or something like that. >> highly unlikely - it has no load. only way something like that can >> happen is if the retainer ring somehow disappears... >> >>> But being I haven't >>> looked at the base of one of those distributors, I couldn't say >>> if they use one. I had this happen on my ford truck one time >>> though. The pin sheared off at the base, and the dist would >>> "wander" and gradually shift in direction until it got to the point >>> that I ran out of room to turn it. Yanked it out, and saw the >>> gone pin. They had those at the autoparts, and I was back >>> off to the races. Seems to me, if the timing marks look >>> perfectly spot on, it should be pretty close, but I've seen >>> weirder things happen.. >>> MK >>> >> check the belt timing. you have all the classic symptoms. > |
Re: DelSol B16A Ignition Timing out but Cam Belt Timing is correct
fish wrote:
> Its actually got a brand new distributor on it. > The car had a misfire so I ordered an ignition module and a coil but > got sent a whole distributor. Result! > Missfire was solved, but the timing issue is the same with both dizzys. if it spans both distributors, the only thing it can be is the belt. > > I too was convinced all the symptoms pointed towards the timing belt, > but I have checked it numerous times. get the helm manual and check it in reference to that. if the belt is slack, it's easy for the pulleys to "look about right" but they're not. > > Everything seems to line up the arrows on the cams point upwards, it's set relative the head, not vertical. the head's slightly sloped. > the > center lines line up, and the TDC mark ( white on by itself) lines up > with the mark on the plastic casing. > > I'm no professional, so I'm going to have take it to a garage to have > them check the cambelt. you can do it yourself if you have the correct info! knowledge is the key. > > I was expecting something not to line up. At least by a few degrees. > > > > jim beam wrote: >> nm5k@wt.net wrote: >>> TeGGeR? wrote: >>> >>>> Then your timing belt is off, even if it looks like it's not. >>> Could be.. The only other thing I could think of is maybe a >>> sheared dist gear pin, or something like that. >> highly unlikely - it has no load. only way something like that can >> happen is if the retainer ring somehow disappears... >> >>> But being I haven't >>> looked at the base of one of those distributors, I couldn't say >>> if they use one. I had this happen on my ford truck one time >>> though. The pin sheared off at the base, and the dist would >>> "wander" and gradually shift in direction until it got to the point >>> that I ran out of room to turn it. Yanked it out, and saw the >>> gone pin. They had those at the autoparts, and I was back >>> off to the races. Seems to me, if the timing marks look >>> perfectly spot on, it should be pretty close, but I've seen >>> weirder things happen.. >>> MK >>> >> check the belt timing. you have all the classic symptoms. > |
Re: DelSol B16A Ignition Timing out but Cam Belt Timing is correct
fish wrote:
> Its actually got a brand new distributor on it. > The car had a misfire so I ordered an ignition module and a coil but > got sent a whole distributor. Result! > Missfire was solved, but the timing issue is the same with both dizzys. if it spans both distributors, the only thing it can be is the belt. > > I too was convinced all the symptoms pointed towards the timing belt, > but I have checked it numerous times. get the helm manual and check it in reference to that. if the belt is slack, it's easy for the pulleys to "look about right" but they're not. > > Everything seems to line up the arrows on the cams point upwards, it's set relative the head, not vertical. the head's slightly sloped. > the > center lines line up, and the TDC mark ( white on by itself) lines up > with the mark on the plastic casing. > > I'm no professional, so I'm going to have take it to a garage to have > them check the cambelt. you can do it yourself if you have the correct info! knowledge is the key. > > I was expecting something not to line up. At least by a few degrees. > > > > jim beam wrote: >> nm5k@wt.net wrote: >>> TeGGeR? wrote: >>> >>>> Then your timing belt is off, even if it looks like it's not. >>> Could be.. The only other thing I could think of is maybe a >>> sheared dist gear pin, or something like that. >> highly unlikely - it has no load. only way something like that can >> happen is if the retainer ring somehow disappears... >> >>> But being I haven't >>> looked at the base of one of those distributors, I couldn't say >>> if they use one. I had this happen on my ford truck one time >>> though. The pin sheared off at the base, and the dist would >>> "wander" and gradually shift in direction until it got to the point >>> that I ran out of room to turn it. Yanked it out, and saw the >>> gone pin. They had those at the autoparts, and I was back >>> off to the races. Seems to me, if the timing marks look >>> perfectly spot on, it should be pretty close, but I've seen >>> weirder things happen.. >>> MK >>> >> check the belt timing. you have all the classic symptoms. > |
All times are GMT -4. The time now is 01:03 PM. |
© 2024 MH Sub I, LLC dba Internet Brands