Dimmer Switch Replacement
 

I have a 1988 LXi. The low beam lights do not work but the high beam lights do. I have replaced the bulbs and have been told that I need to replace the dimmer switch located on the steering column. Is this the problem and how do I replace it
Jame

--
jtfraz

-----------------------------------------------------------------------
View this thread: http://www.carstalk.net/viewtopic-355719.htm

Send from http://www.carstalk.ne

Re: Dimmer Switch Replacement
 

jtfraz wrote:

> I have a 1988 LXi. The low beam lights do not work but the high beam
> lights do. I have replaced the bulbs and have been told that I need to
> replace the dimmer switch located on the steering column. Is this the
> problem and how do I replace it? James

Have you checked the fuses? I may be wrong, but I think the high and low
beams have separate fuses.

Re: Dimmer Switch Replacement
 

I can't find the fuse for this on the wiring diagrams (see www.autozone.com
's free repair guides), but it might be there.

Instructions for removing the switch appear at www.autozone.com 's free
repair guides, too. It looks pretty easy. Go to Chassis Electrical,
Instrument Switches, etc.

"jtfraz" <jtfraz.1xo686@no-mx.carstalk.net> wrote
> I have a 1988 LXi. The low beam lights do not work but the high beam
lights do. I have replaced the bulbs and have been told that I need to
replace the dimmer switch located on the steering column. Is this the
problem and how do I replace it?
> James
>
>
> --
> jtfraz
>
> ------------------------------------------------------------------------
> View this thread: http://www.carstalk.net/viewtopic-355719.html
>
> Send from http://www.carstalk.net
>

Re: Dimmer Switch Replacement
 

jtfraz wrote:
>
> I have a 1988 LXi. The low beam lights do not work but the high beam lights do. I have replaced the bulbs and have been told that I need to replace the dimmer switch located on the steering column. Is this the problem and how do I replace it?
> James
>
> --
> jtfraz
>
> ------------------------------------------------------------------------

Check also the connectors . . They get very loose because people don't
realize the 'trick' to getting them off, so the brass lugs get bent
really loose from being torqued all over the place, then overheat and
you get an open circuit on the Lo Beams, You can sometimes snap the
plastic socket off, rebend the lugs, reassemble the socket and be good
to go.

'Curly'

Re: Dimmer Switch Replacement
 

'Curly Q. Links' wrote:
> jtfraz wrote:
>
>>I have a 1988 LXi. The low beam lights do not work but the high beam lights do. I have replaced the bulbs and have been told that I need to replace the dimmer switch located on the steering column. Is this the problem and how do I replace it?
>>James
>>
>>--
>>jtfraz
>>
>>------------------------------------------------------------------------
>
>
> Check also the connectors . . They get very loose because people don't
> realize the 'trick' to getting them off,

so, what /is/ this trick?

> so the brass lugs get bent
> really loose from being torqued all over the place, then overheat and
> you get an open circuit on the Lo Beams, You can sometimes snap the
> plastic socket off, rebend the lugs, reassemble the socket and be good
> to go.
>
> 'Curly'

Re: Dimmer Switch Replacement
 

jim beam wrote:
>
> 'Curly Q. Links' wrote:
> > Check also the connectors . . They get very loose because people don't
> > realize the 'trick' to getting them off,
>
> so, what /is/ this trick?
>
> > so the brass lugs get bent
> > really loose from being torqued all over the place, then overheat and
> > you get an open circuit on the Lo Beams, You can sometimes snap the
> > plastic socket off, rebend the lugs, reassemble the socket and be good
> > to go.
> >
> > 'Curly'

--------------------------

(on our '95 Odyssey) there were 'dots' on either side of the headlight
connector, where you squeeze to release the gripper that's holding the
socket on to the holes on the bulb's lugs. They are (very) hard to
release, but apparently that's the way Honda wanted to keep the
connector 'anchored' on the bulb. I don't know what other models / years
this trick applies to.

Aside from that, any connector that's been yanked around can start to
fit loose, and if it's a high current connection, it will get HOT and
burn up. With fuse boxes, it will blow the fuse repeatedly because the
fuse gets too hot to carry the right load.

'Curly'