Heater Blower on 98 Civic
 

I own a 1998 Honda Civic EX Sedan. It has 194,000 miles.

When I turn on the heater, to level 1, level 2, whatever, that blower
doesn't turn on.

I inquired about this before. I went to the dealer and explained that it
may be a simple problem like a bad blower resistor, a $20 part. Worst
case scenario, I need a new control assemby unit. I may need a new
control cable, a $5 part.

Should I just get a new blower resistor and take my chances?

--
Message posted using http://www.talkaboutautos.com/group/alt.autos.honda/
More information at http://www.talkaboutautos.com/faq.html

Re: Heater Blower on 98 Civic
 

warlock162 wrote:
> I own a 1998 Honda Civic EX Sedan. It has 194,000 miles.
>
> When I turn on the heater, to level 1, level 2, whatever, that blower
> doesn't turn on.
>
> I inquired about this before. I went to the dealer and explained that it
> may be a simple problem like a bad blower resistor, a $20 part. Worst
> case scenario, I need a new control assemby unit. I may need a new
> control cable, a $5 part.
>
> Should I just get a new blower resistor and take my chances?
>

----------------------------

You forgot to tell us if the fan _ever_ blows air. If not, unplug it,
remove three screws and it falls on the passenger's floor. Hook it up to
12 v (polarity doesn't matter for a short test) and see if the motor is
OK. Then decide what needs fixing. At almost 200,000 miles, the brushes
may well be toast. Get a replacement at the wrecker.

I can't imagine owning a vehicle with a dead blower. It was -40 the
other day.

'Curly'

Re: Heater Blower on 98 Civic
 

Even before the fan didn't blow out air, I had period of a few years when I
turned the A/C on to level 1 and level 2, and nothing worked, but it would
work on level 3 and level 4.

Now it won't work on any level. Does that still mean bad blower resistor.

--
Message posted using http://www.talkaboutautos.com/group/alt.autos.honda/
More information at http://www.talkaboutautos.com/faq.html

Re: Heater Blower on 98 Civic
 

"warlock162" <bray@dwsd.org> wrote in
news:2eb2db9cc7e21b7430ac10a4115789a4@localhost.ta lkaboutautos.com:

> Even before the fan didn't blow out air, I had period of a few years
> when I turned the A/C on to level 1 and level 2, and nothing worked,
> but it would work on level 3 and level 4.
>
> Now it won't work on any level. Does that still mean bad blower
> resistor.
>



It might. The fact that the two lower speeds had previously failed is a
sign that this /may/ be the case.

However...

It is unusual for the two larger (higher speed) resistor coils to break.

Curly is absolutely right. You MUST do a bit of grunt work yourself in
order to correctly diagnose the problem.

The correct procedure here is to remove the resistor and check it visually
and for continuity. Broken coils will be obvious. If the resistor checks
out, then you jump the motor to see if it works at all.

Sorry, but there is no labor-free "magic bullet" here.

--
Tegger

The Unofficial Honda/Acura FAQ
www.tegger.com/hondafaq/

Re: Heater Blower on 98 Civic
 

Tegger wrote:

> "warlock162" <bray@dwsd.org> wrote in
> news:2eb2db9cc7e21b7430ac10a4115789a4@localhost.ta lkaboutautos.com:
>
>
>>Even before the fan didn't blow out air, I had period of a few years
>>when I turned the A/C on to level 1 and level 2, and nothing worked,
>>but it would work on level 3 and level 4.
>>
>>Now it won't work on any level. Does that still mean bad blower
>>resistor.
>>
>
>
>
>
> It might. The fact that the two lower speeds had previously failed is a
> sign that this /may/ be the case.
>
> However...
>
> It is unusual for the two larger (higher speed) resistor coils to break.
>
> Curly is absolutely right. You MUST do a bit of grunt work yourself in
> order to correctly diagnose the problem.
>
> The correct procedure here is to remove the resistor and check it visually
> and for continuity. Broken coils will be obvious. If the resistor checks
> out, then you jump the motor to see if it works at all.
>
> Sorry, but there is no labor-free "magic bullet" here.
>
You may have a problem with the switch itself...
Every vehicle I ever serviced put full voltage to the motor at highest
speed. (No resistor in place at full speed). So, if the resistor was
the culprit, then it should at least work at the highest speed. I agree
with the former poster that indicated you should drop the (blower) motor
and check it against 12v. If it doesn't spin at full speed, then the
brushes indeed may be toast, not unusual at 200K miles. You may be able
to futz around with them and get a few thousand more miles from them,
but the real solution is replace the blower motor. Once you know hou
have a good blower motor, you should have high speed operation at switch
position 4, otherwise the switch may be a contributing issue. Of
course, if the blower motor works when hooked up outside the car, and
not at all inside, it'w worth another check of the fuse(s) and/or
relay(s) to make sure they are OK
Relative to lower speeds, (once you have high speed operation at the
highest position), you may indeed have a problem with the resistors.
Once you can locate them, it's typically a minor issue to pull them out
and even a visual inspection should indicate whether they are OK or not....

Some vehicles (though in the minority) actually require a separate
ground connection for the lower speeds to work. In those cases,
anything below the highest speed won't work unless the ground is in
place. It sounds odd, but there are some really strange wiring setups in
some cars... (Like the way the in-tank fuel pump uses the same ground as
the tail/brake lights on certain models of Chevy Vega, making for
"interesting" action if the ground wire gets damaged in a rear-end
collision, or the 70's Malibu that would allow the radio to work if you
put the (standard transmission) in reverse and stepped on the brake
pedal... another "common ground" issue).

All worth a little investigation....

--Rick