Trying to remove bolts from Catalytic converter..
 

The front of the cat has a flexable connections with bolts and springs. No
problem here. The back end of the cat has three threaded studs/bolts coming
out of the flange. I'm hoping to reuse the cat but I cannot get these three
bolts out of the cat.. I had to cut the rusted nuts off to disassemble and I
need to be able to bolt this end of the cat onto the new pipe I'm replacing.
Looks like I'm going to have to grind the flange flush on both sides and
drill the holes out to accept three new bolts????

I've never seen perminant bolts like this?? I've seen a fixed nut on one
flange but not the bolt.????

When I look up new Catalytic converters it looks like there are holes there
not threaded studs???

Could these bolts be badlt rusted in place? I wacked it pretty hard and have
just about cut one of the "heads" off (they look like a "t" head not a nut
shape) and the shaft of the bolt wont budge... Like its part of the flange..


Is this unusual????


Thanks

Steve

Re: Trying to remove bolts from Catalytic converter..
 

What year Honda? How many miles on it?

Just want to double check: Have you tried soaking the threads as best you
can in PB Blaster for a few times a day, then overnight, or similar, then
tried breaking them free?

PB Blaster is remarkable stuff. It freed some nasty exhaust bolts/nuts on
which I was working a couple of years ago, though it still took some serious
leverage.

I think the exhaust bolts are second only to certain suspension bolts in
seizing over time. The suspension bolts are prone to break before they free.
People seem to have much more luck with exhaust bolts.

"Steve" <junk@therivets.net> wrote
> The front of the cat has a flexable connections with bolts and springs. No
> problem here. The back end of the cat has three threaded studs/bolts
> coming out of the flange. I'm hoping to reuse the cat but I cannot get
> these three bolts out of the cat.. I had to cut the rusted nuts off to
> disassemble and I need to be able to bolt this end of the cat onto the new
> pipe I'm replacing. Looks like I'm going to have to grind the flange flush
> on both sides and drill the holes out to accept three new bolts????
>
> I've never seen perminant bolts like this?? I've seen a fixed nut on one
> flange but not the bolt.????
>
> When I look up new Catalytic converters it looks like there are holes
> there not threaded studs???
>
> Could these bolts be badlt rusted in place? I wacked it pretty hard and
> have just about cut one of the "heads" off (they look like a "t" head not
> a nut shape) and the shaft of the bolt wont budge... Like its part of the
> flange..
>
>
> Is this unusual????
>
>
> Thanks
>
> Steve
>

Re: Trying to remove bolts from Catalytic converter..
 

> What year Honda? How many miles on it?
Its a 98 Civic with 75,000 miles

> Just want to double check: Have you tried soaking the threads as best you
> can in PB Blaster for a few times a day, then overnight, or similar, then
> tried breaking them free?
I've never used PB Blaster, I sprayed with wd40..
Because I'm working under the car with the car on ramps and jack stands I
dont have enough room to get good leverage so I ususlly have to cut off
these stuborn nuts/bolts.

I expected to be able to then remove what was left of the bolts and replace
them with new ones. These seem to be one with the flange???

Steve

>
> PB Blaster is remarkable stuff. It freed some nasty exhaust bolts/nuts on
> which I was working a couple of years ago, though it still took some
> serious leverage.
>
> I think the exhaust bolts are second only to certain suspension bolts in
> seizing over time. The suspension bolts are prone to break before they
> free. People seem to have much more luck with exhaust bolts.
>
> "Steve" <junk@therivets.net> wrote
>> The front of the cat has a flexable connections with bolts and springs.
>> No problem here. The back end of the cat has three threaded studs/bolts
>> coming out of the flange. I'm hoping to reuse the cat but I cannot get
>> these three bolts out of the cat.. I had to cut the rusted nuts off to
>> disassemble and I need to be able to bolt this end of the cat onto the
>> new pipe I'm replacing. Looks like I'm going to have to grind the flange
>> flush on both sides and drill the holes out to accept three new bolts????
>>
>> I've never seen perminant bolts like this?? I've seen a fixed nut on one
>> flange but not the bolt.????
>>
>> When I look up new Catalytic converters it looks like there are holes
>> there not threaded studs???
>>
>> Could these bolts be badlt rusted in place? I wacked it pretty hard and
>> have just about cut one of the "heads" off (they look like a "t" head not
>> a nut shape) and the shaft of the bolt wont budge... Like its part of the
>> flange..
>>
>>
>> Is this unusual????
>>
>>
>> Thanks
>>
>> Steve
>>
>
>

Re: Trying to remove bolts from Catalytic converter..
 

"Steve" <junk@therivets.net> wrote
>> What year Honda? How many miles on it?
> Its a 98 Civic with 75,000 miles
>
>> Just want to double check: Have you tried soaking the threads as best you
>> can in PB Blaster for a few times a day, then overnight, or similar, then
>> tried breaking them free?
> I've never used PB Blaster, I sprayed with wd40..

WD-40 is not a penetrating oil. PB Blaster is, and it might make a huge
difference. It's available at Autozone, Wal-Mart, and the like. Under $5 a
can.

I use a long piece of pipe on the handle of my wrenches for leverage.
Working beneath the car, one can still often squeeze out that extra 1/8 inch
to break free a bolt or nut. Using a hammer on the end of a breaker bar
might work, too. Hitting the nut or bolt, vibrating it, can shake free some
rust as well.

> Because I'm working under the car with the car on ramps and jack stands I
> dont have enough room to get good leverage so I ususlly have to cut off
> these stuborn nuts/bolts.
>
> I expected to be able to then remove what was left of the bolts and
> replace them with new ones. These seem to be one with the flange???

I haven't dug into the drawings of this car's exhaust yet, so I can't
comment. I own a 91 Civic. On a car like yours that is so much younger, I'd
feel the PB Blaster is worth a gamble.

Of note: Many exhaust bolts are fine threaded, to reduce the chances of
their vibrating free. With rust, heat, and road salt, the fine thread is
part of the problem here.

Re: Trying to remove bolts from Catalytic converter..
 

Steve wrote:
>
> The front of the cat has a flexable connections with bolts and springs. No
> problem here. The back end of the cat has three threaded studs/bolts
> coming out of the flange. I'm hoping to reuse the cat but I cannot get
> these three bolts out of the cat.. I had to cut the rusted nuts off to
> disassemble and I need to be able to bolt this end of the cat onto the new
> pipe I'm replacing.
>
> Looks like I'm going to have to grind the flange flush on both sides and
> drill the holes out to accept three new bolts????
>
> I've never seen perminant bolts like this?? I've seen a fixed nut on one
> flange but not the bolt.????
>
> When I look up new Catalytic converters it looks like there are holes
> there not threaded studs???
>
> Could these bolts be badlt rusted in place? I wacked it pretty hard and
> have just about cut one of the "heads" off (they look like a "t" head not
> a nut shape) and the shaft of the bolt wont budge... Like its part of the
> flange..
>
> Is this unusual????
>
> Thanks
>
> Steve

The best way to have dealt with those nuts would have been to heat them up
with a torch until they were red hot and then remove them with an impact
socket (which is less sensitive to heat than chrome sockets). If you don't
have access to an oxy-acetylene torch then sometimes a MAPP gas torch will
work. I believe that the studs are likely welded to the cat. At least
they're shown as part of the cat in the service manual for my '88 Civic.

Eric

Re: Trying to remove bolts from Catalytic converter..
 

"Steve" <junk@therivets.net> wrote in message
news:OoednZwcEKQywXvenZ2dnUVZ_tWdnZ2d@giganews.com ...
> The front of the cat has a flexable connections with bolts and springs. No
> problem here. The back end of the cat has three threaded studs/bolts
> coming out of the flange. I'm hoping to reuse the cat but I cannot get
> these three bolts out of the cat.. I had to cut the rusted nuts off to
> disassemble and I need to be able to bolt this end of the cat onto the new
> pipe I'm replacing. Looks like I'm going to have to grind the flange flush
> on both sides and drill the holes out to accept three new bolts????
>
> I've never seen perminant bolts like this?? I've seen a fixed nut on one
> flange but not the bolt.????
>
> When I look up new Catalytic converters it looks like there are holes
> there not threaded studs???
>
> Could these bolts be badlt rusted in place? I wacked it pretty hard and
> have just about cut one of the "heads" off (they look like a "t" head not
> a nut shape) and the shaft of the bolt wont budge... Like its part of the
> flange..
>
>
> Is this unusual????
>
>
> Thanks
>
> Steve
>
If they are nuts, I have a trick that often helps me. If they are bolts it
won't help.

Clamp a pair of vise-grips as hard as you can on a pair of the flats of a
nut, then spray penetrant on the end of the stud. (As Elle says, WD-40
really isn't the best choice.) Let it sit for a minute or two and move the
vise grips to another pair of flats if they are accessible and repeat. Do
that to all the sides of all the nuts you can reach.

Clamping the vise-grips on one axis forces the threads to bottom out and
opens up teeny gaps at right angles for the penetrant to get in, and also
upsets the bond they have been making over the years. I don't know how much
it reduces breakaway torque but it has freed pretty much every nut I've used
the technique on.

Mike

Re: Trying to remove bolts from Catalytic converter..
 

"Michael Pardee" <michaeltnull@cybertrails.com> wrote
snip
> If they are nuts, I have a trick that often helps me. If they are bolts it
> won't help.
>
> Clamp a pair of vise-grips as hard as you can on a pair of the flats of a
> nut, then spray penetrant on the end of the stud. (As Elle says, WD-40
> really isn't the best choice.)

To clarify: WD-40 is absolutely the wrong choice. PB Blaster is the only
choice.

Michael's technique with the vise-grips looks real good, though.

Re: Trying to remove bolts from Catalytic converter..
 

Check out http://www.hondaautomotiveparts.com for an exploded parts
diagram to see whether the original part has studs or bolts.

As for various penetrating oils, they're all just organic liquids,
based on their MSDSs, and so would not react chemically with rust.
Kerosene was used for this purpose on the old days, and for all anyone
really knows, works as well.

Re: Trying to remove bolts from Catalytic converter..
 

On Tue, 07 Feb 2006 15:33:49 GMT, "Elle"
<honda.lioness@nospam.earthlink.net> wrote:

>"Michael Pardee" <michaeltnull@cybertrails.com> wrote
>snip
>> If they are nuts, I have a trick that often helps me. If they are bolts it
>> won't help.
>>
>> Clamp a pair of vise-grips as hard as you can on a pair of the flats of a
>> nut, then spray penetrant on the end of the stud. (As Elle says, WD-40
>> really isn't the best choice.)
>
>To clarify: WD-40 is absolutely the wrong choice. PB Blaster is the only
>choice.
>
>Michael's technique with the vise-grips looks real good, though.
>
I went through this today, they are studs that are fluted and
pressed in. I cut the nut side off with a torch, then heated the
flange and knocked them out with an air hammer.
Chip