Purchased my 2006 Sonata V6 in September, 2005. They give you 4 years on a
new vehicle here in NJ. So, today I go over to get the inspection done
since I have some time. I had to sit in line for just over 30 minutes.

I get in the facility, get out of the car, and I see the CEL come on. I
keep my mouth shut knowing they will fail me anyway. Guy gets in the car
and tries to rev the engine....nothing happens....it just idles. He puts
it in gear and it drives fine. Back in park and it won't rev up.

Now I am figuring this is some computer screw up as it has never happened
to me before. I suggest turning the engine off and then on again. He does
it. Engine now revs fine and CEL went off.

But....when they hook up the OBDII reader, the engine still tossed two
codes that they had to fail me for.

P1295 and P0638.

Now my car is still under warranty, so I am probably going to let the
dealer have a go at this one, but I would really like to know if anyone has
seen this before after a long idling period. And Hyudaitech, maybe you can
interpret those codes for me?

Thanks,
Eric


BTW, I just turned 50,000 miles yesterday...my inspection report shows
50,038 to be exact. The emission warranty is 5/60 here I think.

 

This is from the Hmaservice website.

2006 > G 3.3 DOHC > P0638 Throttle Actuator Control Range/Performance
Checking output signals from TPS. under detecting condition, if the
difference between real and target throttle position is above the specified
value, PCM sets P0638. MIL(Malfunction Indication Lamp) turns on when the
malfunction lasts till 1 driving cycle.

2006 > G 3.3 DOHC > P1295 ETC (Electronic Throttle Control) System
Malfunction - Power Management
If power management mode is recognized under detecting condition, PCM sets
P1295. And MIL(Malfunction Indication Lamp) turns on.


The Electronic Throttle Control(ETC) system is made of the components
throttle body, Throttle Position Sensor(TPS)1&2 and Accelerator Position
Sensor(APS) 1&2. The throttle body contains the actuator, the throttle plate
and the throttle position sensor (potentiometer), which are integrated in
one housing. The actuator consists of a DC motor with a two-stage gear. The
opening angle of the throttle valve is detected by the throttle position
sensor which is mounted on the throttle body. And it provides feedback to
the PCM to control the throttle motor in order to control the throttle valve
opening angle properly in response to the driving condition

"Eric G." <NgOrSePeAnM99@Zoptonline.Znet> wrote in message
news:Xns9C748795BB28FXz124HiiUdfEEE6@209.197.15.25 4...
> Purchased my 2006 Sonata V6 in September, 2005. They give you 4 years on
> a
> new vehicle here in NJ. So, today I go over to get the inspection done
> since I have some time. I had to sit in line for just over 30 minutes.
>
> I get in the facility, get out of the car, and I see the CEL come on. I
> keep my mouth shut knowing they will fail me anyway. Guy gets in the car
> and tries to rev the engine....nothing happens....it just idles. He puts
> it in gear and it drives fine. Back in park and it won't rev up.
>
> Now I am figuring this is some computer screw up as it has never happened
> to me before. I suggest turning the engine off and then on again. He
> does
> it. Engine now revs fine and CEL went off.
>
> But....when they hook up the OBDII reader, the engine still tossed two
> codes that they had to fail me for.
>
> P1295 and P0638.
>
> Now my car is still under warranty, so I am probably going to let the
> dealer have a go at this one, but I would really like to know if anyone
> has
> seen this before after a long idling period. And Hyudaitech, maybe you
> can
> interpret those codes for me?
>
> Thanks,
> Eric
>
>
> BTW, I just turned 50,000 miles yesterday...my inspection report shows
> 50,038 to be exact. The emission warranty is 5/60 here I think.

 

Thanks! So they both relate to the throttle in one way or another.
This is very interesting considering the throttle problem I mentioned.
First time and only time it has ever happened thus far.

And also amazingly, the CEL went off after driving the car a few times.
I'm wondering if this was just a fluke one time thing. My appt. at the
dealer is 9/1, but I may attempt to take it back for re-inspection
before then. It doesn't hurt you here if you fail twice.

Eric

"Partner" <someone@comcast.net> wrote in
news:h76p33$pl0$1@news.eternal-september.org:

> This is from the Hmaservice website.
>
> 2006 > G 3.3 DOHC > P0638 Throttle Actuator Control Range/Performance
> Checking output signals from TPS. under detecting condition, if the
> difference between real and target throttle position is above the
> specified value, PCM sets P0638. MIL(Malfunction Indication Lamp)
> turns on when the malfunction lasts till 1 driving cycle.
>
> 2006 > G 3.3 DOHC > P1295 ETC (Electronic Throttle Control) System
> Malfunction - Power Management
> If power management mode is recognized under detecting condition, PCM
> sets P1295. And MIL(Malfunction Indication Lamp) turns on.
>
>
> The Electronic Throttle Control(ETC) system is made of the components
> throttle body, Throttle Position Sensor(TPS)1&2 and Accelerator
> Position Sensor(APS) 1&2. The throttle body contains the actuator, the
> throttle plate and the throttle position sensor (potentiometer), which
> are integrated in one housing. The actuator consists of a DC motor
> with a two-stage gear. The opening angle of the throttle valve is
> detected by the throttle position sensor which is mounted on the
> throttle body. And it provides feedback to the PCM to control the
> throttle motor in order to control the throttle valve opening angle
> properly in response to the driving condition
>
> "Eric G." <NgOrSePeAnM99@Zoptonline.Znet> wrote in message
> news:Xns9C748795BB28FXz124HiiUdfEEE6@209.197.15.25 4...
>> Purchased my 2006 Sonata V6 in September, 2005. They give you 4
>> years on a
>> new vehicle here in NJ. So, today I go over to get the inspection
>> done since I have some time. I had to sit in line for just over 30
>> minutes.
>>
>> I get in the facility, get out of the car, and I see the CEL come on.
>> I keep my mouth shut knowing they will fail me anyway. Guy gets in
>> the car and tries to rev the engine....nothing happens....it just
>> idles. He puts it in gear and it drives fine. Back in park and it
>> won't rev up.
>>
>> Now I am figuring this is some computer screw up as it has never
>> happened to me before. I suggest turning the engine off and then on
>> again. He does
>> it. Engine now revs fine and CEL went off.
>>
>> But....when they hook up the OBDII reader, the engine still tossed
>> two codes that they had to fail me for.
>>
>> P1295 and P0638.
>>
>> Now my car is still under warranty, so I am probably going to let the
>> dealer have a go at this one, but I would really like to know if
>> anyone has
>> seen this before after a long idling period. And Hyudaitech, maybe
>> you can
>> interpret those codes for me?
>>
>> Thanks,
>> Eric
>>
>>
>> BTW, I just turned 50,000 miles yesterday...my inspection report
>> shows 50,038 to be exact. The emission warranty is 5/60 here I
>> think.
>
>

 

Be careful that you don't take it back in for inspection too soon after the
dealer (or anyone) clears the codes, a status is set and doesn't clear
until a number of drive cycles have been driven. This status will also
cause a rejection. This is to stop people from clearing the codes and going
straight to the inspection before the error can recur.
Are you saying that he failed you even though the CEL was not on, just
because he found the codes set?


"Eric G." <NgOrSePeAnM99@Zoptonline.Znet> wrote in message
news:Xns9C74B5C08EB77Xz124HiiUdfEEE6@209.197.15.25 4...
> Thanks! So they both relate to the throttle in one way or another.
> This is very interesting considering the throttle problem I mentioned.
> First time and only time it has ever happened thus far.
>
> And also amazingly, the CEL went off after driving the car a few times.
> I'm wondering if this was just a fluke one time thing. My appt. at the
> dealer is 9/1, but I may attempt to take it back for re-inspection
> before then. It doesn't hurt you here if you fail twice.
>
> Eric
>
> "Partner" <someone@comcast.net> wrote in
> news:h76p33$pl0$1@news.eternal-september.org:
>
>> This is from the Hmaservice website.
>>
>> 2006 > G 3.3 DOHC > P0638 Throttle Actuator Control Range/Performance
>> Checking output signals from TPS. under detecting condition, if the
>> difference between real and target throttle position is above the
>> specified value, PCM sets P0638. MIL(Malfunction Indication Lamp)
>> turns on when the malfunction lasts till 1 driving cycle.
>>
>> 2006 > G 3.3 DOHC > P1295 ETC (Electronic Throttle Control) System
>> Malfunction - Power Management
>> If power management mode is recognized under detecting condition, PCM
>> sets P1295. And MIL(Malfunction Indication Lamp) turns on.
>>
>>
>> The Electronic Throttle Control(ETC) system is made of the components
>> throttle body, Throttle Position Sensor(TPS)1&2 and Accelerator
>> Position Sensor(APS) 1&2. The throttle body contains the actuator, the
>> throttle plate and the throttle position sensor (potentiometer), which
>> are integrated in one housing. The actuator consists of a DC motor
>> with a two-stage gear. The opening angle of the throttle valve is
>> detected by the throttle position sensor which is mounted on the
>> throttle body. And it provides feedback to the PCM to control the
>> throttle motor in order to control the throttle valve opening angle
>> properly in response to the driving condition
>>
>> "Eric G." <NgOrSePeAnM99@Zoptonline.Znet> wrote in message
>> news:Xns9C748795BB28FXz124HiiUdfEEE6@209.197.15.25 4...
>>> Purchased my 2006 Sonata V6 in September, 2005. They give you 4
>>> years on a
>>> new vehicle here in NJ. So, today I go over to get the inspection
>>> done since I have some time. I had to sit in line for just over 30
>>> minutes.
>>>
>>> I get in the facility, get out of the car, and I see the CEL come on.
>>> I keep my mouth shut knowing they will fail me anyway. Guy gets in
>>> the car and tries to rev the engine....nothing happens....it just
>>> idles. He puts it in gear and it drives fine. Back in park and it
>>> won't rev up.
>>>
>>> Now I am figuring this is some computer screw up as it has never
>>> happened to me before. I suggest turning the engine off and then on
>>> again. He does
>>> it. Engine now revs fine and CEL went off.
>>>
>>> But....when they hook up the OBDII reader, the engine still tossed
>>> two codes that they had to fail me for.
>>>
>>> P1295 and P0638.
>>>
>>> Now my car is still under warranty, so I am probably going to let the
>>> dealer have a go at this one, but I would really like to know if
>>> anyone has
>>> seen this before after a long idling period. And Hyudaitech, maybe
>>> you can
>>> interpret those codes for me?
>>>
>>> Thanks,
>>> Eric
>>>
>>>
>>> BTW, I just turned 50,000 miles yesterday...my inspection report
>>> shows 50,038 to be exact. The emission warranty is 5/60 here I
>>> think.
>>
>>
>

 

"Partner" <someone@comcast.net> wrote in
news:h77gqp$bl1$1@news.eternal-september.org:

> Be careful that you don't take it back in for inspection too soon
> after the dealer (or anyone) clears the codes, a status is set and
> doesn't clear until a number of drive cycles have been driven. This
> status will also cause a rejection. This is to stop people from
> clearing the codes and going straight to the inspection before the
> error can recur. Are you saying that he failed you even though the CEL
> was not on, just because he found the codes set?
>

No, sorry. I know what I wrote was a little confusing. The CEL was on
initially, then turned off, then apparently was on again. It was still on
when I took possesion of the car again, but turned off after a little bit
of driving. And I was warned by the dealer about the drive cycle
requirement. I am headed out now to the inspection station. All they can
do is fail me again if need be and I already have a dealer appointment next
Tuesday.

Thanks again,
Eric

 

The inspection station was too jammed yesterday, so I went this morning
after a midnight shift and passed without an issue. I'm probably still
going to let the dealer have a look to see if maybe it was something more
than a fluke.

Eric

"Eric G." <NgOrSePeAnM99@Zoptonline.Znet> wrote in
news:Xns9C758C4B96D92Xz124HiiUdfEEE6@209.197.15.25 4:

> "Partner" <someone@comcast.net> wrote in
> news:h77gqp$bl1$1@news.eternal-september.org:
>
>> Be careful that you don't take it back in for inspection too soon
>> after the dealer (or anyone) clears the codes, a status is set and
>> doesn't clear until a number of drive cycles have been driven. This
>> status will also cause a rejection. This is to stop people from
>> clearing the codes and going straight to the inspection before the
>> error can recur. Are you saying that he failed you even though the
>> CEL was not on, just because he found the codes set?
>>
>
> No, sorry. I know what I wrote was a little confusing. The CEL was
> on initially, then turned off, then apparently was on again. It was
> still on when I took possesion of the car again, but turned off after
> a little bit of driving. And I was warned by the dealer about the
> drive cycle requirement. I am headed out now to the inspection
> station. All they can do is fail me again if need be and I already
> have a dealer appointment next Tuesday.
>
> Thanks again,
> Eric
>

 

On Aug 27, 4:08 pm, "Partner" <some...@comcast.net> wrote:
> This is from the Hmaservice website.
>
> 2006 > G 3.3 DOHC > P0638 Throttle Actuator Control Range/Performance
> Checking output signals from TPS. under detecting condition, if the
> difference between real and target throttle position is above the specified
> value, PCM sets P0638. MIL(Malfunction Indication Lamp) turns on when the
> malfunction lasts till 1 driving cycle.
>
> 2006 > G 3.3 DOHC > P1295 ETC (Electronic Throttle Control) System
> Malfunction - Power Management
> If power management mode is recognized under detecting condition, PCM sets
> P1295. And MIL(Malfunction Indication Lamp) turns on.
>
> The Electronic Throttle Control(ETC) system is made of the components
> throttle body, Throttle Position Sensor(TPS)1&2 and Accelerator Position
> Sensor(APS) 1&2. The throttle body contains the actuator, the throttle plate
> and the throttle position sensor (potentiometer), which are integrated in
> one housing. The actuator consists of a DC motor with a two-stage gear. The
> opening angle of the throttle valve is detected by the throttle position
> sensor which is mounted on the throttle body. And it provides feedback to
> the PCM to control the throttle motor in order to control the throttle valve
> opening angle properly in response to the driving condition


The plain English translation of all this is that P0638 set and the
check engine lamp came on because the PCM perceived it was unable to
move the throttle plate to the desired position. P1295 sets when a
power management mode is entered. In this case, because the PCM
detected a problem with the throttle body, it limited engine rpm to
prevent uncontrolled acceleration. There's a technical service
bulletin regarding this problem. It instructs the technician to
replace the throttle position sensor and reprogram the PCM. If you
haven't done this already, have it done soon. The car isn't very
driveable when the problem occurs.

 

hyundaitech <hyundaimech@gmail.com> wrote in
news:fa45f3c7-75d8-420a-960a-c28c335fe981@v2g2000vbb.googlegroups.com:


> The plain English translation of all this is that P0638 set and the
> check engine lamp came on because the PCM perceived it was unable to
> move the throttle plate to the desired position. P1295 sets when a
> power management mode is entered. In this case, because the PCM
> detected a problem with the throttle body, it limited engine rpm to
> prevent uncontrolled acceleration. There's a technical service
> bulletin regarding this problem. It instructs the technician to
> replace the throttle position sensor and reprogram the PCM. If you
> haven't done this already, have it done soon. The car isn't very
> driveable when the problem occurs.
>

Thanks, HT. Haven't seen this TSB. Will look and get it applied soon.

Eric