Wiring problems
 

I have a 96 Accent and have noticed that there are a lot of wiring
problems... like the door bell not chiming all the time and one of the
wires in the code reader circuit working half the time... Did anyone
else have a similar problem? And if so, what was the best way that you
took care of it? The one that is the most annoying of all the wiring
is the one to the code reader since I have my own and sometimes it
takes 2 hours of moving wires around to actually get it long enough to
get a code.

Re: Wiring problems
 

On Feb 25, 11:09 pm, "mmcc...@gmail.com" <mmcc...@gmail.com> wrote:
> I have a 96 Accent and have noticed that there are a lot of wiring
> problems... like the door bell not chiming all the time and one of the
> wires in the code reader circuit working half the time... Did anyone
> else have a similar problem? And if so, what was the best way that you
> took care of it? The one that is the most annoying of all the wiring
> is the one to the code reader since I have my own and sometimes it
> takes 2 hours of moving wires around to actually get it long enough to
> get a code.

I'm guessing you've got a problem with the door switch and perhaps a
poor connection at the DLC. Check for loose terminals there. If
these are indeed wiring problems, when the problem is occurring, check
using an ohmmeter to locate and repair the issue. In most cases, you
should be able to do that in a little more than the 2 hours you spent
moving wires around.

Re: Wiring problems
 

On Feb 26, 10:56 pm, hyundaitech <hyundaim...@gmail.com> wrote:
> On Feb 25, 11:09 pm, "mmcc...@gmail.com" <mmcc...@gmail.com> wrote:
>
> > I have a 96 Accent and have noticed that there are a lot of wiring
> > problems... like the door bell not chiming all the time and one of the
> > wires in the code reader circuit working half the time... Did anyone
> > else have a similar problem? And if so, what was the best way that you
> > took care of it? The one that is the most annoying of all the wiring
> > is the one to the code reader since I have my own and sometimes it
> > takes 2 hours of moving wires around to actually get it long enough to
> > get a code.
>
> I'm guessing you've got a problem with the door switch and perhaps a
> poor connection at the DLC. Check for loose terminals there. If
> these are indeed wiring problems, when the problem is occurring, check
> using an ohmmeter to locate and repair the issue. In most cases, you
> should be able to do that in a little more than the 2 hours you spent
> moving wires around.

It was actually one of the wires underneath the steering wheel for the
door chime, that it would be moved a certain way then the door would
chime, I just wasn't sure if there was an easier way than tackling
every single wire individually, and if there was an easier way just
to replace it all.

Re: Wiring problems
 

On Feb 27, 6:27 pm, mmcclaf <mmcc...@gmail.com> wrote:
> On Feb 26, 10:56 pm, hyundaitech <hyundaim...@gmail.com> wrote:
>
>
>
> > On Feb 25, 11:09 pm, "mmcc...@gmail.com" <mmcc...@gmail.com> wrote:
>
> > > I have a 96 Accent and have noticed that there are a lot of wiring
> > > problems... like the door bell not chiming all the time and one of the
> > > wires in the code reader circuit working half the time... Did anyone
> > > else have a similar problem? And if so, what was the best way that you
> > > took care of it? The one that is the most annoying of all the wiring
> > > is the one to the code reader since I have my own and sometimes it
> > > takes 2 hours of moving wires around to actually get it long enough to
> > > get a code.
>
> > I'm guessing you've got a problem with the door switch and perhaps a
> > poor connection at the DLC. Check for loose terminals there. If
> > these are indeed wiring problems, when the problem is occurring, check
> > using an ohmmeter to locate and repair the issue. In most cases, you
> > should be able to do that in a little more than the 2 hours you spent
> > moving wires around.
>
> It was actually one of the wires underneath the steering wheel for the
> door chime, that it would be moved a certain way then the door would
> chime, I just wasn't sure if there was an easier way than tackling
> every single wire individually, and if there was an easier way just
> to replace it all.

You're not so much checking every wire as you are checking the
individual wire which controls the feature in question. In the case
of the door chime, you'd need to look at a schematic, check the
circuit operation, and check the wire color and routing. I'm guessing
you'll find the problem to be the insulation rubbed through on some
metal component. When the metal touches the strands of the
appropriate wire, it'll make the door chime sound.