Finally Getting Out My 97 Ek All Motor Partout!!!
Finally Getting Out My 97 Ek All Motor Partout!!!
like it says i'm completely parting out my 97 ek hatch everything must go and priced the lowest
engine
-b20/v-tec still in car running mint.no oil burning or leaking motor has 6000 kms since full build by cesar and mark of MISSISSAUGA ENGINES all parts in and on motor were all brand new when motor was built 6 months ago motor was street/dyno tuned right after build.tuned by andrew zeeman with neptune car made 208 whp and 149 torque on conservative tune. on race tune this motor can make 220 whp. new timing belt/water pump this is the meanest sounding motor ever! just crusing into a parking lot everyone knows that's a serious setup
and the loudest v-tec i've ever heard due to all the goodies on the head. on crappy street slicks car ran 13.4 at 105 mph spinning 1st and 2nd with non lsd tranny .put a slick and lsd tranny you can easily do mid 12's
block $1500
-jdm b20b block bore/hone weiseco 11-1 pistons
-eagle rods
-arp main studs
-arp rod bolts
-rebuilt oil pump
-all new bearings
head $1000 no cams intake manifold or throttle body
-p72 usdm gsr head
-ported intake and exhaust ports
-lightened rockers
-ferrea stainless steel exhaust valves
-competition valve job
-5 angle valve job
-skunk 2 titanium retainers and dual valve springs
exhaust
-tri y hytech replica header $450
-2.5' exhaust magnaflow cat,resanator and a flat black vibrant muffler $500
miscelaneous
-skunk 2 pro 2 camshafts $600
-skunk 2 68 mm throttle body $150
-skunk 2 pro series intake manifold ported to 70 mm and ported runners $250
-siemens mopar 550 cc injectors $100
-aem fuel pressure regulator $50
-avid solid race mounts and brackets $250
-stage 5 exedy 4 puck disc unsprung $100
-stage 4 exedy pressure plate $100
-walbro 255 lph pump $75
-integra shift linkages with stock integra dual bend shifter $75
-tuned chipped p-28 ecu $75
-obd-2 v-tec dizzy $100
-b series starter $40
-obd-2a - obd-1 jumper harness $75
located in oakville
--------------------------------------------------------------------------------------------------------
usdm itr 5 lug complete setup just bolt on and go comes with brand new cross drilled/slotted/plated rotors with all parts including e-brake cables lines etc skunk 2 coilovers and koni yellows up fron and koni reds on the back car rides perfect $1400
-6 light gunmetal usdm itr wheels 4 have kumho ecsta tires all 195/50/50 2 have 90% other 2 have 70% 1 has some kinda bad camber wear other spare 2 rims have a set of advan street slicks that are done. $600 2 rims have very minor scuffs absolutely no curb rash!!!
or take all for $1800
located in oakville pm me only with your phone number and only if you wanna buy this stuff or your pm will be ignored thanks everyone!!
engine
-b20/v-tec still in car running mint.no oil burning or leaking motor has 6000 kms since full build by cesar and mark of MISSISSAUGA ENGINES all parts in and on motor were all brand new when motor was built 6 months ago motor was street/dyno tuned right after build.tuned by andrew zeeman with neptune car made 208 whp and 149 torque on conservative tune. on race tune this motor can make 220 whp. new timing belt/water pump this is the meanest sounding motor ever! just crusing into a parking lot everyone knows that's a serious setup
and the loudest v-tec i've ever heard due to all the goodies on the head. on crappy street slicks car ran 13.4 at 105 mph spinning 1st and 2nd with non lsd tranny .put a slick and lsd tranny you can easily do mid 12's
block $1500
-jdm b20b block bore/hone weiseco 11-1 pistons
-eagle rods
-arp main studs
-arp rod bolts
-rebuilt oil pump
-all new bearings
head $1000 no cams intake manifold or throttle body
-p72 usdm gsr head
-ported intake and exhaust ports
-lightened rockers
-ferrea stainless steel exhaust valves
-competition valve job
-5 angle valve job
-skunk 2 titanium retainers and dual valve springs
exhaust
-tri y hytech replica header $450
-2.5' exhaust magnaflow cat,resanator and a flat black vibrant muffler $500
miscelaneous
-skunk 2 pro 2 camshafts $600
-skunk 2 68 mm throttle body $150
-skunk 2 pro series intake manifold ported to 70 mm and ported runners $250
-siemens mopar 550 cc injectors $100
-aem fuel pressure regulator $50
-avid solid race mounts and brackets $250
-stage 5 exedy 4 puck disc unsprung $100
-stage 4 exedy pressure plate $100
-walbro 255 lph pump $75
-integra shift linkages with stock integra dual bend shifter $75
-tuned chipped p-28 ecu $75
-obd-2 v-tec dizzy $100
-b series starter $40
-obd-2a - obd-1 jumper harness $75
located in oakville
--------------------------------------------------------------------------------------------------------
usdm itr 5 lug complete setup just bolt on and go comes with brand new cross drilled/slotted/plated rotors with all parts including e-brake cables lines etc skunk 2 coilovers and koni yellows up fron and koni reds on the back car rides perfect $1400
-6 light gunmetal usdm itr wheels 4 have kumho ecsta tires all 195/50/50 2 have 90% other 2 have 70% 1 has some kinda bad camber wear other spare 2 rims have a set of advan street slicks that are done. $600 2 rims have very minor scuffs absolutely no curb rash!!!
or take all for $1800
located in oakville pm me only with your phone number and only if you wanna buy this stuff or your pm will be ignored thanks everyone!!
Last edited by B18C1EF; Jun 19, 2008 at 12:11 AM.
~~ Hardcore Newb ~~
Joined: Jul 2007
Posts: 29
From: Niagara region
Rep Power: 685 
interested in skunk 2 manifold will this fit a b17a1 motor? im just wondering i kno its a bolt on for the motor but if i put it on will i need to tune my car just wondering thanks.
Thread
Thread Starter
Forum
Replies
Last Post
honda video
Honda Videos
0
Sep 10, 2008 10:48 AM
honda video
Honda Videos
0
Sep 10, 2008 08:11 AM
jflores42
Honda Civic - Del Sol - CRX
2
Apr 13, 2008 09:41 AM
B18C1EF
Car Parts For Sale
10
Oct 9, 2007 11:40 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)