View Poll Results: Did this help you?
Voters: 10. You may not vote on this poll
Shifter LED Tutorial
12-12-2004, 10:28 PM
#19
GTcars - Post God !
Thread Starter
Join Date: Sep 2003
Location: Macomb, Michigan
Posts: 6,032
Rep Power: 879 
ah yeah, silicone sealant/adhesive works really well to insulate the exposed leads of the LED, just make sure they work right before putting it on liek I did. I was wiring that face plate and used the silicone adhesive and now I might have to buy a new faceplate for my cd player... 
12-18-2004, 12:37 AM
#24
Skilled GTcars Poster
Join Date: Oct 2004
Location: St. Petersburg, FL
Posts: 731
Rep Power: 731
Alright thanks I will try that I kind of tryed to touch it up but it was rusted there was a medal plate between the light and shifter plate I dont know what it was for other than to block teh heat? i took it out it was majorly rusted.
02-09-2005, 10:32 PM
#25
Skilled GTcars Poster
Join Date: Oct 2004
Location: St. Petersburg, FL
Posts: 731
Rep Power: 731
I got a new plate heres some pics but I am going to run into the same problem with this one it is off of a 91 RS and I got a shifter handle I belive it is the same one that came on IROC's they are both in really good condition not rusted like my last one!
Ok the pic below show the plate. The bottom of it, the hump were the original light goes in and it causes a problem cause I cant drill stright down and put it aim the led on the letter so I am thinking of drilling holes where the red dots are (except the P,1 Gear cause you can drill stright down on the letter for them) at a 45 degree angle so it will point at the letters does it look like it will work?? I dont want to mess up another shift panel!! Please if you see a better way TELL ME.
Ok the pic below show the plate. The bottom of it, the hump were the original light goes in and it causes a problem cause I cant drill stright down and put it aim the led on the letter so I am thinking of drilling holes where the red dots are (except the P,1 Gear cause you can drill stright down on the letter for them) at a 45 degree angle so it will point at the letters does it look like it will work?? I dont want to mess up another shift panel!! Please if you see a better way TELL ME.
02-09-2005, 10:32 PM
#26
Skilled GTcars Poster
Join Date: Oct 2004
Location: St. Petersburg, FL
Posts: 731
Rep Power: 731
I got a new plate heres some pics but I am going to run into the same problem with this one it is off of a 91 RS and I got a shifter handle I belive it is the same one that came on IROC's they are both in really good condition not rusted like my last one!
Ok the pic below show the plate. The bottom of it, the hump were the original light goes in and it causes a problem cause I cant drill stright down and put it aim the led on the letter so I am thinking of drilling holes where the red dots are (except the P,1 Gear cause you can drill stright down on the letter for them) at a 45 degree angle so it will point at the letters does it look like it will work?? I dont want to mess up another shift panel!! Please if you see a better way TELL ME.
Ok the pic below show the plate. The bottom of it, the hump were the original light goes in and it causes a problem cause I cant drill stright down and put it aim the led on the letter so I am thinking of drilling holes where the red dots are (except the P,1 Gear cause you can drill stright down on the letter for them) at a 45 degree angle so it will point at the letters does it look like it will work?? I dont want to mess up another shift panel!! Please if you see a better way TELL ME.
02-09-2005, 11:58 PM
#27
GTcars - Post God !
Thread Starter
Join Date: Sep 2003
Location: Macomb, Michigan
Posts: 6,032
Rep Power: 879
well, before you drill anything, try taking like a bunch of LEDs and putting them in that hole (MAKE SURE YOU TAPE THE LEADS SO THEY DONT SHORT!) and see how bright they make it?
I mean... that bulb is supposed to light up all the letters, if you shove like 5 of those LED's into that hole and try covering the hole so the only place the light can go is straight to the panel, what does it look like?
I mean... that bulb is supposed to light up all the letters, if you shove like 5 of those LED's into that hole and try covering the hole so the only place the light can go is straight to the panel, what does it look like?
02-09-2005, 11:58 PM
#28
GTcars - Post God !
Thread Starter
Join Date: Sep 2003
Location: Macomb, Michigan
Posts: 6,032
Rep Power: 879
well, before you drill anything, try taking like a bunch of LEDs and putting them in that hole (MAKE SURE YOU TAPE THE LEADS SO THEY DONT SHORT!) and see how bright they make it?
I mean... that bulb is supposed to light up all the letters, if you shove like 5 of those LED's into that hole and try covering the hole so the only place the light can go is straight to the panel, what does it look like?
I mean... that bulb is supposed to light up all the letters, if you shove like 5 of those LED's into that hole and try covering the hole so the only place the light can go is straight to the panel, what does it look like?
12-27-2005, 06:57 PM
#30
Skilled GTcars Poster
Join Date: Oct 2004
Location: Alabama
Posts: 701
Rep Power: 731
why are you even doing this mod this way? to me it looks like that hole is made for a #194 bulbs socket.. if thats the case you could of just ordered a 194 led bulb from anywhere off the internet or even some local shops and just replaced the factory bulb with it
Thread
Thread Starter
Forum
Replies
Last Post
honda video
Honda Videos
0
09-01-2008 11:22 PM
honda video
Honda Videos
0
07-04-2008 02:10 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)