I have a 1991 Honda Accord SE that recently started a high pitch squeal
coming from the engine bay. When sitting at idle, nothing. When
starting to drive, a squeal that starts for awhile and then dissapates
to start all over again. I have searched and searched and read that it
could be anything from ABS motor, timing belt, Distributor, and
alternator bearning. It is coming from the passenger side of the bay
and tried running next to car to isolate but cannot. Distributor
housing, rotor, ignitor, and cap all replaces last year so don't think
that is it?

Can ANYBODY Help me?????

 

viking wrote:
>
> I have a 1991 Honda Accord SE that recently started a high pitch squeal
> coming from the engine bay. When sitting at idle, nothing. When
> starting to drive, a squeal that starts for awhile and then dissapates
> to start all over again. I have searched and searched and read that it
> could be anything from ABS motor, timing belt, Distributor, and
> alternator bearning. It is coming from the passenger side of the bay
> and tried running next to car to isolate but cannot. Distributor
> housing, rotor, ignitor, and cap all replaces last year so don't think
> that is it?
>
> Can ANYBODY Help me?????



---------------------------------

Remove the distributor cap and look for Red Rust. Check google (groups)
if you find red rust.

'Curly'

 

"viking" <teamviking00@yahoo.com> wrote in message news:1131245596.541690.201090@g43g2000cwa.googlegr oups.com...

> I have a 1991 Honda Accord SE that recently started a high pitch squeal
> coming from the engine bay. When sitting at idle, nothing. When
> starting to drive, a squeal that starts for awhile and then dissapates
> to start all over again. I have searched and searched and read that it
> could be anything from ABS motor, timing belt, Distributor, and
> alternator bearning. It is coming from the passenger side of the bay
> and tried running next to car to isolate but cannot. Distributor
> housing, rotor, ignitor, and cap all replaces last year so don't think
> that is it?

If you're running next to the car I would assume the brake pad
wear sensor. If it's from the engine bay maybe spray some WD-40
on the distributor bearing.

 

"Burt S." wrote:
>
> "viking" <teamviking00@yahoo.com> wrote in message news:1131245596.541690.201090@g43g2000cwa.googlegr oups.com...
>
> > I have a 1991 Honda Accord SE that recently started a high pitch squeal
> > coming from the engine bay. When sitting at idle, nothing. When
> > starting to drive, a squeal that starts for awhile and then dissapates
> > to start all over again. I have searched and searched and read that it
> > could be anything from ABS motor, timing belt, Distributor, and
> > alternator bearning. It is coming from the passenger side of the bay
> > and tried running next to car to isolate but cannot. Distributor
> > housing, rotor, ignitor, and cap all replaces last year so don't think
> > that is it?
>
> If you're running next to the car I would assume the brake pad
> wear sensor. If it's from the engine bay maybe spray some WD-40
> on the distributor bearing.

I could be mistaken, but I believe that they are sealed bearings. In order
to lube it, one would need to remove it and pop the seal out, clean it up,
put some grease in it, put the seal back, and then reinstall it back into
the distributor housing. It's not a terribly complex job, but certainly
more involved than just spraying some wd-40 into the distributor (which by
the way probably isn't such a great idea since it's particularly flammable).

Eric

 

Eric wrote:
> "Burt S." wrote:
>
>>"viking" <teamviking00@yahoo.com> wrote in message news:1131245596.541690.201090@g43g2000cwa.googlegr oups.com...
>>
>>
>>>I have a 1991 Honda Accord SE that recently started a high pitch squeal
>>>coming from the engine bay. When sitting at idle, nothing. When
>>>starting to drive, a squeal that starts for awhile and then dissapates
>>>to start all over again. I have searched and searched and read that it
>>>could be anything from ABS motor, timing belt, Distributor, and
>>>alternator bearning. It is coming from the passenger side of the bay
>>>and tried running next to car to isolate but cannot. Distributor
>>>housing, rotor, ignitor, and cap all replaces last year so don't think
>>>that is it?
>>
>>If you're running next to the car I would assume the brake pad
>>wear sensor. If it's from the engine bay maybe spray some WD-40
>>on the distributor bearing.
>
>
> I could be mistaken, but I believe that they are sealed bearings. In order
> to lube it, one would need to remove it and pop the seal out, clean it up,
> put some grease in it, put the seal back, and then reinstall it back into
> the distributor housing. It's not a terribly complex job,

well, it's not that easy either. the bearing is non-standard [and not
cheap] and the housing sensors /should/ be recalibrated on reassembly.
unless you really know what you're doing, replacement of the whole
housing assembly is a much safer thing to do. and if you price your
labor on trying to replace the bearing, there's probably not much in it
on cost either.

> but certainly
> more involved than just spraying some wd-40 into the distributor (which by
> the way probably isn't such a great idea since it's particularly flammable).
>
> Eric

 

viking wrote:
> I have a 1991 Honda Accord SE that recently started a high pitch squeal
> coming from the engine bay. When sitting at idle, nothing. When
> starting to drive, a squeal that starts for awhile and then dissapates
> to start all over again. I have searched and searched and read that it
> could be anything from ABS motor, timing belt, Distributor, and
> alternator bearning. It is coming from the passenger side of the bay
> and tried running next to car to isolate but cannot. Distributor
> housing, rotor, ignitor, and cap all replaces last year so don't think
> that is it?
>
> Can ANYBODY Help me?????
>
sounds like an accessory belt. bearings don't usually get quieter as
revs go up.

when you say "passenger side" is that left or right? depends on the
country you're in!

 

"viking" <teamviking00@yahoo.com> wrote in
news:1131245596.541690.201090@g43g2000cwa.googlegr oups.com:

> I have a 1991 Honda Accord SE that recently started a high pitch squeal
> coming from the engine bay. When sitting at idle, nothing. When
> starting to drive, a squeal that starts for awhile and then dissapates
> to start all over again.


Does the noise start again when you press the brakes to slow down again?
Then inspect the brakes.

Also have all the accessory drive belts checked. Does the noise appear on
the first startup in the morning?



--
TeGGeR®

The Unofficial Honda/Acura FAQ
www.tegger.com/hondafaq/

 

viking wrote:
> I have a 1991 Honda Accord SE that recently started a high pitch squeal
> coming from the engine bay. When sitting at idle, nothing. When
> starting to drive, a squeal that starts for awhile and then dissapates
> to start all over again. I have searched and searched and read that it
> could be anything from ABS motor, timing belt, Distributor, and
> alternator bearning. It is coming from the passenger side of the bay
> and tried running next to car to isolate but cannot. Distributor
> housing, rotor, ignitor, and cap all replaces last year so don't think
> that is it?
>
> Can ANYBODY Help me?????

Thanks all for the responses - but I know it is not the breaks per se
or the accessory belts. The "squeal" is like a fan hitting the shroud
or the radiator and grinding on metal and goes for about 10 sec and
stops and then goes again a few seconds later and stops. It never does
it at a standstill or idle but always does it when driving (whether you
are accelerating or not). Breaking has no impact on the change in
noise other than when you get the forward momentum of the car stopped.
Then no more awefull grinding noise.
I read a post listed 2 years ago that indicated the ABS fuse was pulled
and a noise exactly like the one I have stopped. So in that case -
maybe the anti-lock breaking system has malfunctioned. I'm thinking
more along the problem with timing belt or possibly a malfunctioned
distributor. However, I have questions about distributor making such a
noise- since all is new less than a year ago. And why wouldn't the
distributor make the same noise at standstill if reving the motor up??
Very baffled!!!

 

Thanks Curly. I see just barely some red dust. Hardly noticeable.
And if it is the distributor, wouldn't that grinding noise increase as
I rev up the motor??

 

"jim beam" <nospam@example.net> wrote in message news:1IidnRVM1oeh3vPenZ2dnUVZ_s6dnZ2d@speakeasy.ne t...
> Eric wrote:

> > I could be mistaken, but I believe that they are sealed bearings. In order
> > to lube it, one would need to remove it and pop the seal out, clean it up,
> > put some grease in it, put the seal back, and then reinstall it back into
> > the distributor housing. It's not a terribly complex job,

> well, it's not that easy either. the bearing is non-standard [and not
> cheap] and the housing sensors /should/ be recalibrated on reassembly.
> unless you really know what you're doing, replacement of the whole
> housing assembly is a much safer thing to do. and if you price your
> labor on trying to replace the bearing, there's probably not much in it
> on cost either.

Exactly what I'd say. I'd ripped the distributor apart on a 92 Civic only to
clean, grease and seal it with clear RTV silicone. These bearings are sealed
and not standard otherwise I'd swap the bearing. Overall, I'm expecting the
car to last over 200k.

From a flashlight I can clearly see the distributor bearing on a 92 Accord
after removing the rotor. Get a nice, long nozzle and get a clean shot at
the bearing (sealed or not) while agitating the shaft. The WD-40 molecule
is penetrating enough to stop that squeak.

> > but certainly
> > more involved than just spraying some wd-40 into the distributor (which by
> > the way probably isn't such a great idea since it's particularly flammable).

Not as flammable as aerosol starter fluid.

 

"viking" <teamviking00@yahoo.com> wrote in message
news:1131327844.264998.204890@o13g2000cwo.googlegr oups.com...
>
> viking wrote:
>> I have a 1991 Honda Accord SE that recently started a high pitch squeal
>> coming from the engine bay. When sitting at idle, nothing. When
>> starting to drive, a squeal that starts for awhile and then dissapates
>> to start all over again. I have searched and searched and read that it
>> could be anything from ABS motor, timing belt, Distributor, and
>> alternator bearning. It is coming from the passenger side of the bay
>> and tried running next to car to isolate but cannot. Distributor
>> housing, rotor, ignitor, and cap all replaces last year so don't think
>> that is it?
>>
>> Can ANYBODY Help me?????
>
> Thanks all for the responses - but I know it is not the breaks per se
> or the accessory belts. The "squeal" is like a fan hitting the shroud
> or the radiator and grinding on metal and goes for about 10 sec and
> stops and then goes again a few seconds later and stops. It never does
> it at a standstill or idle but always does it when driving (whether you
> are accelerating or not). Breaking has no impact on the change in
> noise other than when you get the forward momentum of the car stopped.
> Then no more awefull grinding noise.
> I read a post listed 2 years ago that indicated the ABS fuse was pulled
> and a noise exactly like the one I have stopped. So in that case -
> maybe the anti-lock breaking system has malfunctioned. I'm thinking
> more along the problem with timing belt or possibly a malfunctioned
> distributor. However, I have questions about distributor making such a
> noise- since all is new less than a year ago. And why wouldn't the
> distributor make the same noise at standstill if reving the motor up??
> Very baffled!!!
>
Just a thought - my daughter's '93 made an intermittent squalling noise when
the coolant was low. None of the other symptoms, just a squall like a seized
bearing. Weird.

Mike