87 accord won’t idle after fuel pump replacement
05-16-2005, 06:35 PM
#1
Guest
Posts: n/a
87 accord won’t idle after fuel pump replacement
1987 Honda Accord 2.0 carb, bought for my daughter, in an attempt to
fix a rough running engine after 10 to 15 minutes of driving, both
fuel filters were replaced, the plugs were replaced, the wires were
replaced, the distributor cap and rotor were replaced, the coil was
replaced, next, I attempted to replace the fuel pump sock, but had to
replace the fuel pump and sock, in an error on my part, I dropped the
tank to replace it. Once back together, the engine will start, run on
high idle, then when it is to return to normal idle, the engine dies,
you can keep it running by keeping the accelerator depressed, but,
once you let it return to normal, the engine dies, you can restart the
engine, but, once again it dies. Any help would be appreciated.
Thanks.
--
Posted using the http://www.autoforumz.com interface, at author's request
Articles individually checked for conformance to usenet standards
Topic URL: http://www.autoforumz.com/Honda-87-a...ict120478.html
Visit Topic URL to contact author (reg. req'd). Report abuse: http://www.autoforumz.com/eform.php?p=585423
fix a rough running engine after 10 to 15 minutes of driving, both
fuel filters were replaced, the plugs were replaced, the wires were
replaced, the distributor cap and rotor were replaced, the coil was
replaced, next, I attempted to replace the fuel pump sock, but had to
replace the fuel pump and sock, in an error on my part, I dropped the
tank to replace it. Once back together, the engine will start, run on
high idle, then when it is to return to normal idle, the engine dies,
you can keep it running by keeping the accelerator depressed, but,
once you let it return to normal, the engine dies, you can restart the
engine, but, once again it dies. Any help would be appreciated.
Thanks.
--
Posted using the http://www.autoforumz.com interface, at author's request
Articles individually checked for conformance to usenet standards
Topic URL: http://www.autoforumz.com/Honda-87-a...ict120478.html
Visit Topic URL to contact author (reg. req'd). Report abuse: http://www.autoforumz.com/eform.php?p=585423
05-22-2005, 05:43 PM
#2
Guest
Posts: n/a
Re: 87 accord won’t idle after fuel pump replacement
david12314 wrote:
> 1987 Honda Accord 2.0 carb, bought for my daughter, in an attempt to
> fix a rough running engine after 10 to 15 minutes of driving, both
> fuel filters were replaced, the plugs were replaced, the wires were
> replaced, the distributor cap and rotor were replaced, the coil was
> replaced, next, I attempted to replace the fuel pump sock, but had to
> replace the fuel pump and sock, in an error on my part, I dropped the
> tank to replace it. Once back together, the engine will start, run on
> high idle, then when it is to return to normal idle, the engine dies,
> you can keep it running by keeping the accelerator depressed, but,
> once you let it return to normal, the engine dies, you can restart the
> engine, but, once again it dies. Any help would be appreciated.
> Thanks.
Dirty idle jet would be my first guess. Fixing that requires opening up
the carb. Basic carb cleaning on that car isn't too bad though: remove
the air breather, and you'll see (if memory serves) five or six
Philips-head bolts. Pull them out, and take loose the arms the push the
choke and acceleration pump, and just lift the top of carb off. From
there you can blow out the various jets and passageways, and make sure
the float bowl is clean while you're in there. Be careful blasting air
through though, one of the tubes toward the back of the carb body has a
bead valve that'll go flying if you don't cover it up first.
---
avast! Antivirus: Outbound message clean.
Virus Database (VPS): 0520-4, 05/20/2005
Tested on: 5/22/2005 2:42:47 PM
avast! - copyright (c) 1988-2005 ALWIL Software.
http://www.avast.com
> 1987 Honda Accord 2.0 carb, bought for my daughter, in an attempt to
> fix a rough running engine after 10 to 15 minutes of driving, both
> fuel filters were replaced, the plugs were replaced, the wires were
> replaced, the distributor cap and rotor were replaced, the coil was
> replaced, next, I attempted to replace the fuel pump sock, but had to
> replace the fuel pump and sock, in an error on my part, I dropped the
> tank to replace it. Once back together, the engine will start, run on
> high idle, then when it is to return to normal idle, the engine dies,
> you can keep it running by keeping the accelerator depressed, but,
> once you let it return to normal, the engine dies, you can restart the
> engine, but, once again it dies. Any help would be appreciated.
> Thanks.
Dirty idle jet would be my first guess. Fixing that requires opening up
the carb. Basic carb cleaning on that car isn't too bad though: remove
the air breather, and you'll see (if memory serves) five or six
Philips-head bolts. Pull them out, and take loose the arms the push the
choke and acceleration pump, and just lift the top of carb off. From
there you can blow out the various jets and passageways, and make sure
the float bowl is clean while you're in there. Be careful blasting air
through though, one of the tubes toward the back of the carb body has a
bead valve that'll go flying if you don't cover it up first.
---
avast! Antivirus: Outbound message clean.
Virus Database (VPS): 0520-4, 05/20/2005
Tested on: 5/22/2005 2:42:47 PM
avast! - copyright (c) 1988-2005 ALWIL Software.
http://www.avast.com
05-22-2005, 05:43 PM
#3
Guest
Posts: n/a
Re: 87 accord won’t idle after fuel pump replacement
david12314 wrote:
> 1987 Honda Accord 2.0 carb, bought for my daughter, in an attempt to
> fix a rough running engine after 10 to 15 minutes of driving, both
> fuel filters were replaced, the plugs were replaced, the wires were
> replaced, the distributor cap and rotor were replaced, the coil was
> replaced, next, I attempted to replace the fuel pump sock, but had to
> replace the fuel pump and sock, in an error on my part, I dropped the
> tank to replace it. Once back together, the engine will start, run on
> high idle, then when it is to return to normal idle, the engine dies,
> you can keep it running by keeping the accelerator depressed, but,
> once you let it return to normal, the engine dies, you can restart the
> engine, but, once again it dies. Any help would be appreciated.
> Thanks.
Dirty idle jet would be my first guess. Fixing that requires opening up
the carb. Basic carb cleaning on that car isn't too bad though: remove
the air breather, and you'll see (if memory serves) five or six
Philips-head bolts. Pull them out, and take loose the arms the push the
choke and acceleration pump, and just lift the top of carb off. From
there you can blow out the various jets and passageways, and make sure
the float bowl is clean while you're in there. Be careful blasting air
through though, one of the tubes toward the back of the carb body has a
bead valve that'll go flying if you don't cover it up first.
---
avast! Antivirus: Outbound message clean.
Virus Database (VPS): 0520-4, 05/20/2005
Tested on: 5/22/2005 2:42:47 PM
avast! - copyright (c) 1988-2005 ALWIL Software.
http://www.avast.com
> 1987 Honda Accord 2.0 carb, bought for my daughter, in an attempt to
> fix a rough running engine after 10 to 15 minutes of driving, both
> fuel filters were replaced, the plugs were replaced, the wires were
> replaced, the distributor cap and rotor were replaced, the coil was
> replaced, next, I attempted to replace the fuel pump sock, but had to
> replace the fuel pump and sock, in an error on my part, I dropped the
> tank to replace it. Once back together, the engine will start, run on
> high idle, then when it is to return to normal idle, the engine dies,
> you can keep it running by keeping the accelerator depressed, but,
> once you let it return to normal, the engine dies, you can restart the
> engine, but, once again it dies. Any help would be appreciated.
> Thanks.
Dirty idle jet would be my first guess. Fixing that requires opening up
the carb. Basic carb cleaning on that car isn't too bad though: remove
the air breather, and you'll see (if memory serves) five or six
Philips-head bolts. Pull them out, and take loose the arms the push the
choke and acceleration pump, and just lift the top of carb off. From
there you can blow out the various jets and passageways, and make sure
the float bowl is clean while you're in there. Be careful blasting air
through though, one of the tubes toward the back of the carb body has a
bead valve that'll go flying if you don't cover it up first.
---
avast! Antivirus: Outbound message clean.
Virus Database (VPS): 0520-4, 05/20/2005
Tested on: 5/22/2005 2:42:47 PM
avast! - copyright (c) 1988-2005 ALWIL Software.
http://www.avast.com
06-15-2005, 07:36 PM
#4
Guest
Posts: n/a
Re: Re: 87 accord won’t_idle_after_fuel_p
"soundy" wrote:
> david12314 wrote:
>
> > 1987 Honda Accord 2.0 carb, bought for my daughter, in an
> attempt to
> > fix a rough running engine after 10 to 15 minutes of
> driving, both
> > fuel filters were replaced, the plugs were replaced, the
> wires were
> > replaced, the distributor cap and rotor were replaced, the
> coil was
> > replaced, next, I attempted to replace the fuel pump sock,
> but had to
> > replace the fuel pump and sock, in an error on my part, I
> dropped the
> > tank to replace it. Once back together, the engine will
> start, run on
> > high idle, then when it is to return to normal idle, the
> engine dies,
> > you can keep it running by keeping the accelerator
> depressed, but,
> > once you let it return to normal, the engine dies, you can
> restart the
> > engine, but, once again it dies. Any help would be
> appreciated.
> > Thanks.
>
> Dirty idle jet would be my first guess. Fixing that requires
> opening up
> the carb. Basic carb cleaning on that car isn't too bad
> though: remove
> the air breather, and you'll see (if memory serves) five or
> six
> Philips-head bolts. Pull them out, and take loose the arms the
> push the
> choke and acceleration pump, and just lift the top of carb
> off. From
> there you can blow out the various jets and passageways, and
> make sure
> the float bowl is clean while you're in there. Be careful
> blasting air
> through though, one of the tubes toward the back of the carb
> body has a
> bead valve that'll go flying if you don't cover it up first.
>
>
> ---
> avast! Antivirus: Outbound message clean.
> Virus Database (VPS): 0520-4, 05/20/2005
> Tested on: 5/22/2005 2:42:47 PM
> avast! - copyright (c) 1988-2005 ALWIL Software.
> http://www.avast.com
I have an 86 and I have the same problem. I have not replaced the O2
sensor, but I did rebuild the carburetor. the car runs great but will
not idle unless I set the idle speed way up. Any ideas? thanks!!
--
Posted using the http://www.autoforumz.com interface, at author's request
Articles individually checked for conformance to usenet standards
Topic URL: http://www.autoforumz.com/Honda-87-a...ict120478.html
Visit Topic URL to contact author (reg. req'd). Report abuse: http://www.autoforumz.com/eform.php?p=607304
> david12314 wrote:
>
> > 1987 Honda Accord 2.0 carb, bought for my daughter, in an
> attempt to
> > fix a rough running engine after 10 to 15 minutes of
> driving, both
> > fuel filters were replaced, the plugs were replaced, the
> wires were
> > replaced, the distributor cap and rotor were replaced, the
> coil was
> > replaced, next, I attempted to replace the fuel pump sock,
> but had to
> > replace the fuel pump and sock, in an error on my part, I
> dropped the
> > tank to replace it. Once back together, the engine will
> start, run on
> > high idle, then when it is to return to normal idle, the
> engine dies,
> > you can keep it running by keeping the accelerator
> depressed, but,
> > once you let it return to normal, the engine dies, you can
> restart the
> > engine, but, once again it dies. Any help would be
> appreciated.
> > Thanks.
>
> Dirty idle jet would be my first guess. Fixing that requires
> opening up
> the carb. Basic carb cleaning on that car isn't too bad
> though: remove
> the air breather, and you'll see (if memory serves) five or
> six
> Philips-head bolts. Pull them out, and take loose the arms the
> push the
> choke and acceleration pump, and just lift the top of carb
> off. From
> there you can blow out the various jets and passageways, and
> make sure
> the float bowl is clean while you're in there. Be careful
> blasting air
> through though, one of the tubes toward the back of the carb
> body has a
> bead valve that'll go flying if you don't cover it up first.
>
>
> ---
> avast! Antivirus: Outbound message clean.
> Virus Database (VPS): 0520-4, 05/20/2005
> Tested on: 5/22/2005 2:42:47 PM
> avast! - copyright (c) 1988-2005 ALWIL Software.
> http://www.avast.com
I have an 86 and I have the same problem. I have not replaced the O2
sensor, but I did rebuild the carburetor. the car runs great but will
not idle unless I set the idle speed way up. Any ideas? thanks!!
--
Posted using the http://www.autoforumz.com interface, at author's request
Articles individually checked for conformance to usenet standards
Topic URL: http://www.autoforumz.com/Honda-87-a...ict120478.html
Visit Topic URL to contact author (reg. req'd). Report abuse: http://www.autoforumz.com/eform.php?p=607304
06-15-2005, 07:36 PM
#5
Guest
Posts: n/a
Re: Re: 87 accord won’t_idle_after_fuel_p
"soundy" wrote:
> david12314 wrote:
>
> > 1987 Honda Accord 2.0 carb, bought for my daughter, in an
> attempt to
> > fix a rough running engine after 10 to 15 minutes of
> driving, both
> > fuel filters were replaced, the plugs were replaced, the
> wires were
> > replaced, the distributor cap and rotor were replaced, the
> coil was
> > replaced, next, I attempted to replace the fuel pump sock,
> but had to
> > replace the fuel pump and sock, in an error on my part, I
> dropped the
> > tank to replace it. Once back together, the engine will
> start, run on
> > high idle, then when it is to return to normal idle, the
> engine dies,
> > you can keep it running by keeping the accelerator
> depressed, but,
> > once you let it return to normal, the engine dies, you can
> restart the
> > engine, but, once again it dies. Any help would be
> appreciated.
> > Thanks.
>
> Dirty idle jet would be my first guess. Fixing that requires
> opening up
> the carb. Basic carb cleaning on that car isn't too bad
> though: remove
> the air breather, and you'll see (if memory serves) five or
> six
> Philips-head bolts. Pull them out, and take loose the arms the
> push the
> choke and acceleration pump, and just lift the top of carb
> off. From
> there you can blow out the various jets and passageways, and
> make sure
> the float bowl is clean while you're in there. Be careful
> blasting air
> through though, one of the tubes toward the back of the carb
> body has a
> bead valve that'll go flying if you don't cover it up first.
>
>
> ---
> avast! Antivirus: Outbound message clean.
> Virus Database (VPS): 0520-4, 05/20/2005
> Tested on: 5/22/2005 2:42:47 PM
> avast! - copyright (c) 1988-2005 ALWIL Software.
> http://www.avast.com
I have an 86 and I have the same problem. I have not replaced the O2
sensor, but I did rebuild the carburetor. the car runs great but will
not idle unless I set the idle speed way up. Any ideas? thanks!!
--
Posted using the http://www.autoforumz.com interface, at author's request
Articles individually checked for conformance to usenet standards
Topic URL: http://www.autoforumz.com/Honda-87-a...ict120478.html
Visit Topic URL to contact author (reg. req'd). Report abuse: http://www.autoforumz.com/eform.php?p=607304
> david12314 wrote:
>
> > 1987 Honda Accord 2.0 carb, bought for my daughter, in an
> attempt to
> > fix a rough running engine after 10 to 15 minutes of
> driving, both
> > fuel filters were replaced, the plugs were replaced, the
> wires were
> > replaced, the distributor cap and rotor were replaced, the
> coil was
> > replaced, next, I attempted to replace the fuel pump sock,
> but had to
> > replace the fuel pump and sock, in an error on my part, I
> dropped the
> > tank to replace it. Once back together, the engine will
> start, run on
> > high idle, then when it is to return to normal idle, the
> engine dies,
> > you can keep it running by keeping the accelerator
> depressed, but,
> > once you let it return to normal, the engine dies, you can
> restart the
> > engine, but, once again it dies. Any help would be
> appreciated.
> > Thanks.
>
> Dirty idle jet would be my first guess. Fixing that requires
> opening up
> the carb. Basic carb cleaning on that car isn't too bad
> though: remove
> the air breather, and you'll see (if memory serves) five or
> six
> Philips-head bolts. Pull them out, and take loose the arms the
> push the
> choke and acceleration pump, and just lift the top of carb
> off. From
> there you can blow out the various jets and passageways, and
> make sure
> the float bowl is clean while you're in there. Be careful
> blasting air
> through though, one of the tubes toward the back of the carb
> body has a
> bead valve that'll go flying if you don't cover it up first.
>
>
> ---
> avast! Antivirus: Outbound message clean.
> Virus Database (VPS): 0520-4, 05/20/2005
> Tested on: 5/22/2005 2:42:47 PM
> avast! - copyright (c) 1988-2005 ALWIL Software.
> http://www.avast.com
I have an 86 and I have the same problem. I have not replaced the O2
sensor, but I did rebuild the carburetor. the car runs great but will
not idle unless I set the idle speed way up. Any ideas? thanks!!
--
Posted using the http://www.autoforumz.com interface, at author's request
Articles individually checked for conformance to usenet standards
Topic URL: http://www.autoforumz.com/Honda-87-a...ict120478.html
Visit Topic URL to contact author (reg. req'd). Report abuse: http://www.autoforumz.com/eform.php?p=607304
06-15-2005, 08:41 PM
#6
Guest
Posts: n/a
Re: 87 accord won’t_idle_after_fuel_p
Daver86 wrote:
> I have an 86 and I have the same problem. I have not replaced the O2
> sensor, but I did rebuild the carburetor. the car runs great but will
> not idle unless I set the idle speed way up. Any ideas? thanks!!
------------------
Vacuum leaks in one of the multitude hoses :-(
'Curly'
> I have an 86 and I have the same problem. I have not replaced the O2
> sensor, but I did rebuild the carburetor. the car runs great but will
> not idle unless I set the idle speed way up. Any ideas? thanks!!
------------------
Vacuum leaks in one of the multitude hoses :-(
'Curly'
06-15-2005, 08:41 PM
#7
Guest
Posts: n/a
Re: 87 accord won’t_idle_after_fuel_p
Daver86 wrote:
> I have an 86 and I have the same problem. I have not replaced the O2
> sensor, but I did rebuild the carburetor. the car runs great but will
> not idle unless I set the idle speed way up. Any ideas? thanks!!
------------------
Vacuum leaks in one of the multitude hoses :-(
'Curly'
> I have an 86 and I have the same problem. I have not replaced the O2
> sensor, but I did rebuild the carburetor. the car runs great but will
> not idle unless I set the idle speed way up. Any ideas? thanks!!
------------------
Vacuum leaks in one of the multitude hoses :-(
'Curly'
Thread
Thread Starter
Forum
Replies
Last Post
Fade 2 Black
Want To Buy
0
09-18-2007 11:09 PM
toyhelp@cdre.com
Honda Mailing List
6
06-20-2007 04:47 PM
toyhelp@cdre.com
Honda Mailing List
0
06-20-2007 04:29 AM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
