Re: 90 Civic valve issue...
 

meld_b wrote:
>
> Thanks - I'm learning here... Is 250 RPM what the starter spins?

I don't know since I've never clocked it but it probably is the cranking rpm
(on a fully charged battery).

> What does the wide open throttle do for you?

Maximizes air flow, allows the engine to breathe, helps give you the highest
possible compression numbers, etc...

> I'm thinking these numbers are what you use to compare to when you have a
> four plugs pulled and you put the compression checker in each cylinder and
> have someone crank it? So they need to floor it too!?

Yes, or use a brick or pedal depressor and a remote starter switch (and make
sure the car's out of gear so you don't run yourself over).

Eric

Re: 90 Civic valve issue...
 

meld_b wrote:
>
> Thanks - I'm learning here... Is 250 RPM what the starter spins?

I don't know since I've never clocked it but it probably is the cranking rpm
(on a fully charged battery).

> What does the wide open throttle do for you?

Maximizes air flow, allows the engine to breathe, helps give you the highest
possible compression numbers, etc...

> I'm thinking these numbers are what you use to compare to when you have a
> four plugs pulled and you put the compression checker in each cylinder and
> have someone crank it? So they need to floor it too!?

Yes, or use a brick or pedal depressor and a remote starter switch (and make
sure the car's out of gear so you don't run yourself over).

Eric

Re: 90 Civic valve issue...
 

meld_b wrote:
>
> Thanks - I'm learning here... Is 250 RPM what the starter spins?

I don't know since I've never clocked it but it probably is the cranking rpm
(on a fully charged battery).

> What does the wide open throttle do for you?

Maximizes air flow, allows the engine to breathe, helps give you the highest
possible compression numbers, etc...

> I'm thinking these numbers are what you use to compare to when you have a
> four plugs pulled and you put the compression checker in each cylinder and
> have someone crank it? So they need to floor it too!?

Yes, or use a brick or pedal depressor and a remote starter switch (and make
sure the car's out of gear so you don't run yourself over).

Eric

Re: 90 Civic valve issue...
 

Thanks - I think running over yourself trying to fix a car worth about
$600 would have to put me in the running for a Darwin award!! 8-)

No this car isn't in that great of shape, starting to rust on one side,
axles about to go. Heater blower has brushes that are suboptimal. And
most importantly, my wife doesn't want me fiddling with new engines,
etc. So I'm probably off to something new, when I can get around to
it... It is nice how it's giving me time by still moving me around.

-D

Eric wrote:

> Yes, or use a brick or pedal depressor and a remote starter switch (and make
> sure the car's out of gear so you don't run yourself over).
>
> Eric

Re: 90 Civic valve issue...
 

Thanks - I think running over yourself trying to fix a car worth about
$600 would have to put me in the running for a Darwin award!! 8-)

No this car isn't in that great of shape, starting to rust on one side,
axles about to go. Heater blower has brushes that are suboptimal. And
most importantly, my wife doesn't want me fiddling with new engines,
etc. So I'm probably off to something new, when I can get around to
it... It is nice how it's giving me time by still moving me around.

-D

Eric wrote:

> Yes, or use a brick or pedal depressor and a remote starter switch (and make
> sure the car's out of gear so you don't run yourself over).
>
> Eric

Re: 90 Civic valve issue...
 

Thanks - I think running over yourself trying to fix a car worth about
$600 would have to put me in the running for a Darwin award!! 8-)

No this car isn't in that great of shape, starting to rust on one side,
axles about to go. Heater blower has brushes that are suboptimal. And
most importantly, my wife doesn't want me fiddling with new engines,
etc. So I'm probably off to something new, when I can get around to
it... It is nice how it's giving me time by still moving me around.

-D

Eric wrote:

> Yes, or use a brick or pedal depressor and a remote starter switch (and make
> sure the car's out of gear so you don't run yourself over).
>
> Eric

Re: 90 Civic valve issue...
 

hey , i just bought a civic, 1990 and it has a similar issue, but i
don't think it is the actual rings, just the rubber rings at the top of
the cylnder where the plug wires go in. they look old and worn and one
of them is letting a little bit of oil into the cylnder. i was told by
a good friend who is also a very good mechanic friend that if you just
swap out those rubber rings, you should be fine. does anyone know how
to do that or where i can get some information for the job? i'm going
to try to do it myself.

busyness.


--
busynesswithme
Message Origin: TRAVEL.com

Re: 90 Civic valve issue...
 

busynesswithme wrote:
> hey , i just bought a civic, 1990 and it has a similar issue, but i
> don't think it is the actual rings, just the rubber rings at the top of
> the cylnder where the plug wires go in. they look old and worn and one
> of them is letting a little bit of oil into the cylnder. i was told by
> a good friend who is also a very good mechanic friend that if you just
> swap out those rubber rings, you should be fine. does anyone know how
> to do that or where i can get some information for the job? i'm going
> to try to do it myself.
>
> busyness.
>
>
How about your very good mechanic friend? He wouldn't give you any info?

Re: 90 Civic valve issue...
 

busynesswithme <busynesswithme.3jpyc6@no-mx.forums.travel.com> wrote in
news:busynesswithme.3jpyc6@no-mx.forums.travel.com:

>
> hey , i just bought a civic, 1990 and it has a similar issue, but i
> don't think it is the actual rings, just the rubber rings at the top of
> the cylnder where the plug wires go in. they look old and worn and one
> of them is letting a little bit of oil into the cylnder. i was told by
> a good friend who is also a very good mechanic friend that if you just
> swap out those rubber rings, you should be fine. does anyone know how
> to do that or where i can get some information for the job? i'm going
> to try to do it myself.
>



Here's one place:
http://www.tegger.com/hondafaq/oilyplugs/index.html


--
Tegger

The Unofficial Honda/Acura FAQ
www.tegger.com/hondafaq/

Re: 90 Civic valve issue...
 

problem is he's on the other side of the continent or else for sure i
would. i'm going to poke around in there today, bought a haynes
manual, etc. he did say that those rubber rings should be all that is
needed to be replaced. doesn't sound like a big job, just wanting to
find out if anyone knows a little more about it.


--
busynesswithme
Message Origin: TRAVEL.com