91 Civic, no spark
06-02-2005, 04:26 PM
#1
Guest
Posts: n/a
91 Civic, no spark
Hi all, I need help! Please!?!?!?!
91 Civic dx, 1.5l. TEC distributor (which isn't in the Haynes manual)
I've read through the earlier posts on this topic and don't think I've
managed to find the problem.
This thing cranks and cranks, no go. It has fuel, just no spark.
Changed the igniter, still no go. Took the dist. cover off and noticed
that the wire to the side of the igniter did not get put on properly by
the mech who changed the igniter. Fixed that connection up but still no
go. Did we fry the igniter by trying to start it with this wire not
getting good contact?
Next, checked the coil best I could figure out from the manual which
doesn't cover this distributor. Resistance from + to - with the wires
disconnected is 1.2 ohms; 12.5 ohms from the + to the tower; 12.9 from -
to the tower.
Like I said, the Haynes manual doesn't cover a TEC distributor so I
don't have reference values to see if this is right for the coil. Also,
before I rip it back apart was hoping to hear if we screwed the new
igniter in our follies.
Thanx a pile, reply to my email too if you don't mind, it's valid.
Cheers,
Gord
91 Civic dx, 1.5l. TEC distributor (which isn't in the Haynes manual)
I've read through the earlier posts on this topic and don't think I've
managed to find the problem.
This thing cranks and cranks, no go. It has fuel, just no spark.
Changed the igniter, still no go. Took the dist. cover off and noticed
that the wire to the side of the igniter did not get put on properly by
the mech who changed the igniter. Fixed that connection up but still no
go. Did we fry the igniter by trying to start it with this wire not
getting good contact?
Next, checked the coil best I could figure out from the manual which
doesn't cover this distributor. Resistance from + to - with the wires
disconnected is 1.2 ohms; 12.5 ohms from the + to the tower; 12.9 from -
to the tower.
Like I said, the Haynes manual doesn't cover a TEC distributor so I
don't have reference values to see if this is right for the coil. Also,
before I rip it back apart was hoping to hear if we screwed the new
igniter in our follies.
Thanx a pile, reply to my email too if you don't mind, it's valid.
Cheers,
Gord
06-02-2005, 10:08 PM
#2
Guest
Posts: n/a
Re: 91 Civic, no spark
Gord wrote:
> Hi all, I need help! Please!?!?!?!
> 91 Civic dx, 1.5l. TEC distributor (which isn't in the Haynes manual)
> I've read through the earlier posts on this topic and don't think I've
> managed to find the problem.
> This thing cranks and cranks, no go. It has fuel, just no spark.
> Changed the igniter, still no go. Took the dist. cover off and noticed
> that the wire to the side of the igniter did not get put on properly by
> the mech who changed the igniter. Fixed that connection up but still no
> go. Did we fry the igniter by trying to start it with this wire not
> getting good contact?
> Next, checked the coil best I could figure out from the manual which
> doesn't cover this distributor. Resistance from + to - with the wires
> disconnected is 1.2 ohms; 12.5 ohms from the + to the tower; 12.9 from -
> to the tower.
> Like I said, the Haynes manual doesn't cover a TEC distributor so I
> don't have reference values to see if this is right for the coil. Also,
> before I rip it back apart was hoping to hear if we screwed the new
> igniter in our follies.
> Thanx a pile, reply to my email too if you don't mind, it's valid.
> Cheers,
> Gord
is that ohms or k ohms int he coil secondary? if it's ohms, your coil's
dead.
other than that, don't think you fried the igniter with a bad connection.
better diagnosis is like this;
are you getting signal from the ecu?
are you getting power to the igniter?
are you getting power switched from the igniter?
does the coil spark when you energise & release?
are you getting spark from the dist cap/rotor assy?
answering each of those questions will determine fault. all the
individual test methods are described in the faq's or other online sources.
as part of the "power to the igniter" testing, while i don't think it's
common, i recently had the ignition condenser/capacitor fail. it was
near short and was weakening the spark considerably. check it while you
have the distributor open.
> Hi all, I need help! Please!?!?!?!
> 91 Civic dx, 1.5l. TEC distributor (which isn't in the Haynes manual)
> I've read through the earlier posts on this topic and don't think I've
> managed to find the problem.
> This thing cranks and cranks, no go. It has fuel, just no spark.
> Changed the igniter, still no go. Took the dist. cover off and noticed
> that the wire to the side of the igniter did not get put on properly by
> the mech who changed the igniter. Fixed that connection up but still no
> go. Did we fry the igniter by trying to start it with this wire not
> getting good contact?
> Next, checked the coil best I could figure out from the manual which
> doesn't cover this distributor. Resistance from + to - with the wires
> disconnected is 1.2 ohms; 12.5 ohms from the + to the tower; 12.9 from -
> to the tower.
> Like I said, the Haynes manual doesn't cover a TEC distributor so I
> don't have reference values to see if this is right for the coil. Also,
> before I rip it back apart was hoping to hear if we screwed the new
> igniter in our follies.
> Thanx a pile, reply to my email too if you don't mind, it's valid.
> Cheers,
> Gord
is that ohms or k ohms int he coil secondary? if it's ohms, your coil's
dead.
other than that, don't think you fried the igniter with a bad connection.
better diagnosis is like this;
are you getting signal from the ecu?
are you getting power to the igniter?
are you getting power switched from the igniter?
does the coil spark when you energise & release?
are you getting spark from the dist cap/rotor assy?
answering each of those questions will determine fault. all the
individual test methods are described in the faq's or other online sources.
as part of the "power to the igniter" testing, while i don't think it's
common, i recently had the ignition condenser/capacitor fail. it was
near short and was weakening the spark considerably. check it while you
have the distributor open.
06-02-2005, 10:08 PM
#3
Guest
Posts: n/a
Re: 91 Civic, no spark
Gord wrote:
> Hi all, I need help! Please!?!?!?!
> 91 Civic dx, 1.5l. TEC distributor (which isn't in the Haynes manual)
> I've read through the earlier posts on this topic and don't think I've
> managed to find the problem.
> This thing cranks and cranks, no go. It has fuel, just no spark.
> Changed the igniter, still no go. Took the dist. cover off and noticed
> that the wire to the side of the igniter did not get put on properly by
> the mech who changed the igniter. Fixed that connection up but still no
> go. Did we fry the igniter by trying to start it with this wire not
> getting good contact?
> Next, checked the coil best I could figure out from the manual which
> doesn't cover this distributor. Resistance from + to - with the wires
> disconnected is 1.2 ohms; 12.5 ohms from the + to the tower; 12.9 from -
> to the tower.
> Like I said, the Haynes manual doesn't cover a TEC distributor so I
> don't have reference values to see if this is right for the coil. Also,
> before I rip it back apart was hoping to hear if we screwed the new
> igniter in our follies.
> Thanx a pile, reply to my email too if you don't mind, it's valid.
> Cheers,
> Gord
is that ohms or k ohms int he coil secondary? if it's ohms, your coil's
dead.
other than that, don't think you fried the igniter with a bad connection.
better diagnosis is like this;
are you getting signal from the ecu?
are you getting power to the igniter?
are you getting power switched from the igniter?
does the coil spark when you energise & release?
are you getting spark from the dist cap/rotor assy?
answering each of those questions will determine fault. all the
individual test methods are described in the faq's or other online sources.
as part of the "power to the igniter" testing, while i don't think it's
common, i recently had the ignition condenser/capacitor fail. it was
near short and was weakening the spark considerably. check it while you
have the distributor open.
> Hi all, I need help! Please!?!?!?!
> 91 Civic dx, 1.5l. TEC distributor (which isn't in the Haynes manual)
> I've read through the earlier posts on this topic and don't think I've
> managed to find the problem.
> This thing cranks and cranks, no go. It has fuel, just no spark.
> Changed the igniter, still no go. Took the dist. cover off and noticed
> that the wire to the side of the igniter did not get put on properly by
> the mech who changed the igniter. Fixed that connection up but still no
> go. Did we fry the igniter by trying to start it with this wire not
> getting good contact?
> Next, checked the coil best I could figure out from the manual which
> doesn't cover this distributor. Resistance from + to - with the wires
> disconnected is 1.2 ohms; 12.5 ohms from the + to the tower; 12.9 from -
> to the tower.
> Like I said, the Haynes manual doesn't cover a TEC distributor so I
> don't have reference values to see if this is right for the coil. Also,
> before I rip it back apart was hoping to hear if we screwed the new
> igniter in our follies.
> Thanx a pile, reply to my email too if you don't mind, it's valid.
> Cheers,
> Gord
is that ohms or k ohms int he coil secondary? if it's ohms, your coil's
dead.
other than that, don't think you fried the igniter with a bad connection.
better diagnosis is like this;
are you getting signal from the ecu?
are you getting power to the igniter?
are you getting power switched from the igniter?
does the coil spark when you energise & release?
are you getting spark from the dist cap/rotor assy?
answering each of those questions will determine fault. all the
individual test methods are described in the faq's or other online sources.
as part of the "power to the igniter" testing, while i don't think it's
common, i recently had the ignition condenser/capacitor fail. it was
near short and was weakening the spark considerably. check it while you
have the distributor open.
06-02-2005, 10:56 PM
#4
Guest
Posts: n/a
Re: 91 Civic, no spark
Gord <bigoldchevy@hotmail.com> wrote in
news:119uql98q7310de@corp.supernews.com:
> Hi all, I need help! Please!?!?!?!
> 91 Civic dx, 1.5l. TEC distributor (which isn't in the Haynes manual)
> I've read through the earlier posts on this topic and don't think I've
> managed to find the problem.
> This thing cranks and cranks, no go. It has fuel, just no spark.
> Changed the igniter, still no go. Took the dist. cover off and noticed
> that the wire to the side of the igniter did not get put on properly by
> the mech who changed the igniter. Fixed that connection up but still no
> go. Did we fry the igniter by trying to start it with this wire not
> getting good contact?
Coil is toast.
> Next, checked the coil best I could figure out from the manual which
> doesn't cover this distributor. Resistance from + to - with the wires
> disconnected is 1.2 ohms; 12.5 ohms from the + to the tower; 12.9 from -
> to the tower.
Means bugger all. The coil is grounding through its body.
Make certain the NEW coil has a good ground through proper channels,
meaning the rotor, cap, and wires. Use new OEM unless you really like
gambling.
--
TeGGeR®
The Unofficial Honda/Acura FAQ
www.tegger.com/hondafaq/
news:119uql98q7310de@corp.supernews.com:
> Hi all, I need help! Please!?!?!?!
> 91 Civic dx, 1.5l. TEC distributor (which isn't in the Haynes manual)
> I've read through the earlier posts on this topic and don't think I've
> managed to find the problem.
> This thing cranks and cranks, no go. It has fuel, just no spark.
> Changed the igniter, still no go. Took the dist. cover off and noticed
> that the wire to the side of the igniter did not get put on properly by
> the mech who changed the igniter. Fixed that connection up but still no
> go. Did we fry the igniter by trying to start it with this wire not
> getting good contact?
Coil is toast.
> Next, checked the coil best I could figure out from the manual which
> doesn't cover this distributor. Resistance from + to - with the wires
> disconnected is 1.2 ohms; 12.5 ohms from the + to the tower; 12.9 from -
> to the tower.
Means bugger all. The coil is grounding through its body.
Make certain the NEW coil has a good ground through proper channels,
meaning the rotor, cap, and wires. Use new OEM unless you really like
gambling.
--
TeGGeR®
The Unofficial Honda/Acura FAQ
www.tegger.com/hondafaq/
06-02-2005, 10:56 PM
#5
Guest
Posts: n/a
Re: 91 Civic, no spark
Gord <bigoldchevy@hotmail.com> wrote in
news:119uql98q7310de@corp.supernews.com:
> Hi all, I need help! Please!?!?!?!
> 91 Civic dx, 1.5l. TEC distributor (which isn't in the Haynes manual)
> I've read through the earlier posts on this topic and don't think I've
> managed to find the problem.
> This thing cranks and cranks, no go. It has fuel, just no spark.
> Changed the igniter, still no go. Took the dist. cover off and noticed
> that the wire to the side of the igniter did not get put on properly by
> the mech who changed the igniter. Fixed that connection up but still no
> go. Did we fry the igniter by trying to start it with this wire not
> getting good contact?
Coil is toast.
> Next, checked the coil best I could figure out from the manual which
> doesn't cover this distributor. Resistance from + to - with the wires
> disconnected is 1.2 ohms; 12.5 ohms from the + to the tower; 12.9 from -
> to the tower.
Means bugger all. The coil is grounding through its body.
Make certain the NEW coil has a good ground through proper channels,
meaning the rotor, cap, and wires. Use new OEM unless you really like
gambling.
--
TeGGeR®
The Unofficial Honda/Acura FAQ
www.tegger.com/hondafaq/
news:119uql98q7310de@corp.supernews.com:
> Hi all, I need help! Please!?!?!?!
> 91 Civic dx, 1.5l. TEC distributor (which isn't in the Haynes manual)
> I've read through the earlier posts on this topic and don't think I've
> managed to find the problem.
> This thing cranks and cranks, no go. It has fuel, just no spark.
> Changed the igniter, still no go. Took the dist. cover off and noticed
> that the wire to the side of the igniter did not get put on properly by
> the mech who changed the igniter. Fixed that connection up but still no
> go. Did we fry the igniter by trying to start it with this wire not
> getting good contact?
Coil is toast.
> Next, checked the coil best I could figure out from the manual which
> doesn't cover this distributor. Resistance from + to - with the wires
> disconnected is 1.2 ohms; 12.5 ohms from the + to the tower; 12.9 from -
> to the tower.
Means bugger all. The coil is grounding through its body.
Make certain the NEW coil has a good ground through proper channels,
meaning the rotor, cap, and wires. Use new OEM unless you really like
gambling.
--
TeGGeR®
The Unofficial Honda/Acura FAQ
www.tegger.com/hondafaq/
06-03-2005, 08:04 AM
#6
Guest
Posts: n/a
Re: 91 Civic, no spark
jim beam wrote:
> Gord wrote:
>
>> Hi all, I need help! Please!?!?!?!
>> 91 Civic dx, 1.5l. TEC distributor (which isn't in the Haynes manual)
>> I've read through the earlier posts on this topic and don't think I've
>> managed to find the problem.
>> This thing cranks and cranks, no go. It has fuel, just no spark.
>> Changed the igniter, still no go. Took the dist. cover off and
>> noticed that the wire to the side of the igniter did not get put on
>> properly by the mech who changed the igniter. Fixed that connection
>> up but still no go. Did we fry the igniter by trying to start it with
>> this wire not getting good contact?
>> Next, checked the coil best I could figure out from the manual which
>> doesn't cover this distributor. Resistance from + to - with the wires
>> disconnected is 1.2 ohms; 12.5 ohms from the + to the tower; 12.9 from
>> - to the tower.
>> Like I said, the Haynes manual doesn't cover a TEC distributor so I
>> don't have reference values to see if this is right for the coil.
>> Also, before I rip it back apart was hoping to hear if we screwed the
>> new igniter in our follies.
>> Thanx a pile, reply to my email too if you don't mind, it's valid.
>> Cheers,
>> Gord
>
>
> is that ohms or k ohms int he coil secondary? if it's ohms, your coil's
OOPS, yes it was k ohms
> dead.
>
> other than that, don't think you fried the igniter with a bad connection.
>
> better diagnosis is like this;
>
> are you getting signal from the ecu?
> are you getting power to the igniter?
> are you getting power switched from the igniter?
> does the coil spark when you energise & release?
> are you getting spark from the dist cap/rotor assy?
>
> answering each of those questions will determine fault. all the
> individual test methods are described in the faq's or other online sources.
>
> as part of the "power to the igniter" testing, while i don't think it's
> common, i recently had the ignition condenser/capacitor fail. it was
> near short and was weakening the spark considerably. check it while you
> have the distributor open.
>
> Gord wrote:
>
>> Hi all, I need help! Please!?!?!?!
>> 91 Civic dx, 1.5l. TEC distributor (which isn't in the Haynes manual)
>> I've read through the earlier posts on this topic and don't think I've
>> managed to find the problem.
>> This thing cranks and cranks, no go. It has fuel, just no spark.
>> Changed the igniter, still no go. Took the dist. cover off and
>> noticed that the wire to the side of the igniter did not get put on
>> properly by the mech who changed the igniter. Fixed that connection
>> up but still no go. Did we fry the igniter by trying to start it with
>> this wire not getting good contact?
>> Next, checked the coil best I could figure out from the manual which
>> doesn't cover this distributor. Resistance from + to - with the wires
>> disconnected is 1.2 ohms; 12.5 ohms from the + to the tower; 12.9 from
>> - to the tower.
>> Like I said, the Haynes manual doesn't cover a TEC distributor so I
>> don't have reference values to see if this is right for the coil.
>> Also, before I rip it back apart was hoping to hear if we screwed the
>> new igniter in our follies.
>> Thanx a pile, reply to my email too if you don't mind, it's valid.
>> Cheers,
>> Gord
>
>
> is that ohms or k ohms int he coil secondary? if it's ohms, your coil's
OOPS, yes it was k ohms
> dead.
>
> other than that, don't think you fried the igniter with a bad connection.
>
> better diagnosis is like this;
>
> are you getting signal from the ecu?
> are you getting power to the igniter?
> are you getting power switched from the igniter?
> does the coil spark when you energise & release?
> are you getting spark from the dist cap/rotor assy?
>
> answering each of those questions will determine fault. all the
> individual test methods are described in the faq's or other online sources.
>
> as part of the "power to the igniter" testing, while i don't think it's
> common, i recently had the ignition condenser/capacitor fail. it was
> near short and was weakening the spark considerably. check it while you
> have the distributor open.
>
06-03-2005, 08:04 AM
#7
Guest
Posts: n/a
Re: 91 Civic, no spark
jim beam wrote:
> Gord wrote:
>
>> Hi all, I need help! Please!?!?!?!
>> 91 Civic dx, 1.5l. TEC distributor (which isn't in the Haynes manual)
>> I've read through the earlier posts on this topic and don't think I've
>> managed to find the problem.
>> This thing cranks and cranks, no go. It has fuel, just no spark.
>> Changed the igniter, still no go. Took the dist. cover off and
>> noticed that the wire to the side of the igniter did not get put on
>> properly by the mech who changed the igniter. Fixed that connection
>> up but still no go. Did we fry the igniter by trying to start it with
>> this wire not getting good contact?
>> Next, checked the coil best I could figure out from the manual which
>> doesn't cover this distributor. Resistance from + to - with the wires
>> disconnected is 1.2 ohms; 12.5 ohms from the + to the tower; 12.9 from
>> - to the tower.
>> Like I said, the Haynes manual doesn't cover a TEC distributor so I
>> don't have reference values to see if this is right for the coil.
>> Also, before I rip it back apart was hoping to hear if we screwed the
>> new igniter in our follies.
>> Thanx a pile, reply to my email too if you don't mind, it's valid.
>> Cheers,
>> Gord
>
>
> is that ohms or k ohms int he coil secondary? if it's ohms, your coil's
OOPS, yes it was k ohms
> dead.
>
> other than that, don't think you fried the igniter with a bad connection.
>
> better diagnosis is like this;
>
> are you getting signal from the ecu?
> are you getting power to the igniter?
> are you getting power switched from the igniter?
> does the coil spark when you energise & release?
> are you getting spark from the dist cap/rotor assy?
>
> answering each of those questions will determine fault. all the
> individual test methods are described in the faq's or other online sources.
>
> as part of the "power to the igniter" testing, while i don't think it's
> common, i recently had the ignition condenser/capacitor fail. it was
> near short and was weakening the spark considerably. check it while you
> have the distributor open.
>
> Gord wrote:
>
>> Hi all, I need help! Please!?!?!?!
>> 91 Civic dx, 1.5l. TEC distributor (which isn't in the Haynes manual)
>> I've read through the earlier posts on this topic and don't think I've
>> managed to find the problem.
>> This thing cranks and cranks, no go. It has fuel, just no spark.
>> Changed the igniter, still no go. Took the dist. cover off and
>> noticed that the wire to the side of the igniter did not get put on
>> properly by the mech who changed the igniter. Fixed that connection
>> up but still no go. Did we fry the igniter by trying to start it with
>> this wire not getting good contact?
>> Next, checked the coil best I could figure out from the manual which
>> doesn't cover this distributor. Resistance from + to - with the wires
>> disconnected is 1.2 ohms; 12.5 ohms from the + to the tower; 12.9 from
>> - to the tower.
>> Like I said, the Haynes manual doesn't cover a TEC distributor so I
>> don't have reference values to see if this is right for the coil.
>> Also, before I rip it back apart was hoping to hear if we screwed the
>> new igniter in our follies.
>> Thanx a pile, reply to my email too if you don't mind, it's valid.
>> Cheers,
>> Gord
>
>
> is that ohms or k ohms int he coil secondary? if it's ohms, your coil's
OOPS, yes it was k ohms
> dead.
>
> other than that, don't think you fried the igniter with a bad connection.
>
> better diagnosis is like this;
>
> are you getting signal from the ecu?
> are you getting power to the igniter?
> are you getting power switched from the igniter?
> does the coil spark when you energise & release?
> are you getting spark from the dist cap/rotor assy?
>
> answering each of those questions will determine fault. all the
> individual test methods are described in the faq's or other online sources.
>
> as part of the "power to the igniter" testing, while i don't think it's
> common, i recently had the ignition condenser/capacitor fail. it was
> near short and was weakening the spark considerably. check it while you
> have the distributor open.
>
06-03-2005, 08:08 AM
#8
Guest
Posts: n/a
Re: 91 Civic, no spark
jim beam wrote:
> Gord wrote:
>
>> Hi all, I need help! Please!?!?!?!
>> 91 Civic dx, 1.5l. TEC distributor (which isn't in the Haynes manual)
>> I've read through the earlier posts on this topic and don't think I've
>> managed to find the problem.
>> This thing cranks and cranks, no go. It has fuel, just no spark.
>> Changed the igniter, still no go. Took the dist. cover off and
>> noticed that the wire to the side of the igniter did not get put on
>> properly by the mech who changed the igniter. Fixed that connection
>> up but still no go. Did we fry the igniter by trying to start it with
>> this wire not getting good contact?
>> Next, checked the coil best I could figure out from the manual which
>> doesn't cover this distributor. Resistance from + to - with the wires
>> disconnected is 1.2 ohms; 12.5 ohms from the + to the tower; 12.9 from
>> - to the tower.
>> Like I said, the Haynes manual doesn't cover a TEC distributor so I
>> don't have reference values to see if this is right for the coil.
>> Also, before I rip it back apart was hoping to hear if we screwed the
>> new igniter in our follies.
>> Thanx a pile, reply to my email too if you don't mind, it's valid.
>> Cheers,
>> Gord
>
>
> is that ohms or k ohms int he coil secondary? if it's ohms, your coil's
OOPS! k ohms, sorry
> dead.
>
> other than that, don't think you fried the igniter with a bad connection.
>
> better diagnosis is like this;
>
> are you getting signal from the ecu?
not getting any signal from the light under the carpet... with my luck
the light's burned out!
> are you getting power to the igniter?
> are you getting power switched from the igniter?
> does the coil spark when you energise & release?
> are you getting spark from the dist cap/rotor assy?
>
> answering each of those questions will determine fault. all the
> individual test methods are described in the faq's or other online sources.
>
> as part of the "power to the igniter" testing, while i don't think it's
> common, i recently had the ignition condenser/capacitor fail. it was
> near short and was weakening the spark considerably. check it while you
> have the distributor open.
>
> Gord wrote:
>
>> Hi all, I need help! Please!?!?!?!
>> 91 Civic dx, 1.5l. TEC distributor (which isn't in the Haynes manual)
>> I've read through the earlier posts on this topic and don't think I've
>> managed to find the problem.
>> This thing cranks and cranks, no go. It has fuel, just no spark.
>> Changed the igniter, still no go. Took the dist. cover off and
>> noticed that the wire to the side of the igniter did not get put on
>> properly by the mech who changed the igniter. Fixed that connection
>> up but still no go. Did we fry the igniter by trying to start it with
>> this wire not getting good contact?
>> Next, checked the coil best I could figure out from the manual which
>> doesn't cover this distributor. Resistance from + to - with the wires
>> disconnected is 1.2 ohms; 12.5 ohms from the + to the tower; 12.9 from
>> - to the tower.
>> Like I said, the Haynes manual doesn't cover a TEC distributor so I
>> don't have reference values to see if this is right for the coil.
>> Also, before I rip it back apart was hoping to hear if we screwed the
>> new igniter in our follies.
>> Thanx a pile, reply to my email too if you don't mind, it's valid.
>> Cheers,
>> Gord
>
>
> is that ohms or k ohms int he coil secondary? if it's ohms, your coil's
OOPS! k ohms, sorry
> dead.
>
> other than that, don't think you fried the igniter with a bad connection.
>
> better diagnosis is like this;
>
> are you getting signal from the ecu?
not getting any signal from the light under the carpet... with my luck
the light's burned out!
> are you getting power to the igniter?
> are you getting power switched from the igniter?
> does the coil spark when you energise & release?
> are you getting spark from the dist cap/rotor assy?
>
> answering each of those questions will determine fault. all the
> individual test methods are described in the faq's or other online sources.
>
> as part of the "power to the igniter" testing, while i don't think it's
> common, i recently had the ignition condenser/capacitor fail. it was
> near short and was weakening the spark considerably. check it while you
> have the distributor open.
>
06-03-2005, 08:08 AM
#9
Guest
Posts: n/a
Re: 91 Civic, no spark
jim beam wrote:
> Gord wrote:
>
>> Hi all, I need help! Please!?!?!?!
>> 91 Civic dx, 1.5l. TEC distributor (which isn't in the Haynes manual)
>> I've read through the earlier posts on this topic and don't think I've
>> managed to find the problem.
>> This thing cranks and cranks, no go. It has fuel, just no spark.
>> Changed the igniter, still no go. Took the dist. cover off and
>> noticed that the wire to the side of the igniter did not get put on
>> properly by the mech who changed the igniter. Fixed that connection
>> up but still no go. Did we fry the igniter by trying to start it with
>> this wire not getting good contact?
>> Next, checked the coil best I could figure out from the manual which
>> doesn't cover this distributor. Resistance from + to - with the wires
>> disconnected is 1.2 ohms; 12.5 ohms from the + to the tower; 12.9 from
>> - to the tower.
>> Like I said, the Haynes manual doesn't cover a TEC distributor so I
>> don't have reference values to see if this is right for the coil.
>> Also, before I rip it back apart was hoping to hear if we screwed the
>> new igniter in our follies.
>> Thanx a pile, reply to my email too if you don't mind, it's valid.
>> Cheers,
>> Gord
>
>
> is that ohms or k ohms int he coil secondary? if it's ohms, your coil's
OOPS! k ohms, sorry
> dead.
>
> other than that, don't think you fried the igniter with a bad connection.
>
> better diagnosis is like this;
>
> are you getting signal from the ecu?
not getting any signal from the light under the carpet... with my luck
the light's burned out!
> are you getting power to the igniter?
> are you getting power switched from the igniter?
> does the coil spark when you energise & release?
> are you getting spark from the dist cap/rotor assy?
>
> answering each of those questions will determine fault. all the
> individual test methods are described in the faq's or other online sources.
>
> as part of the "power to the igniter" testing, while i don't think it's
> common, i recently had the ignition condenser/capacitor fail. it was
> near short and was weakening the spark considerably. check it while you
> have the distributor open.
>
> Gord wrote:
>
>> Hi all, I need help! Please!?!?!?!
>> 91 Civic dx, 1.5l. TEC distributor (which isn't in the Haynes manual)
>> I've read through the earlier posts on this topic and don't think I've
>> managed to find the problem.
>> This thing cranks and cranks, no go. It has fuel, just no spark.
>> Changed the igniter, still no go. Took the dist. cover off and
>> noticed that the wire to the side of the igniter did not get put on
>> properly by the mech who changed the igniter. Fixed that connection
>> up but still no go. Did we fry the igniter by trying to start it with
>> this wire not getting good contact?
>> Next, checked the coil best I could figure out from the manual which
>> doesn't cover this distributor. Resistance from + to - with the wires
>> disconnected is 1.2 ohms; 12.5 ohms from the + to the tower; 12.9 from
>> - to the tower.
>> Like I said, the Haynes manual doesn't cover a TEC distributor so I
>> don't have reference values to see if this is right for the coil.
>> Also, before I rip it back apart was hoping to hear if we screwed the
>> new igniter in our follies.
>> Thanx a pile, reply to my email too if you don't mind, it's valid.
>> Cheers,
>> Gord
>
>
> is that ohms or k ohms int he coil secondary? if it's ohms, your coil's
OOPS! k ohms, sorry
> dead.
>
> other than that, don't think you fried the igniter with a bad connection.
>
> better diagnosis is like this;
>
> are you getting signal from the ecu?
not getting any signal from the light under the carpet... with my luck
the light's burned out!
> are you getting power to the igniter?
> are you getting power switched from the igniter?
> does the coil spark when you energise & release?
> are you getting spark from the dist cap/rotor assy?
>
> answering each of those questions will determine fault. all the
> individual test methods are described in the faq's or other online sources.
>
> as part of the "power to the igniter" testing, while i don't think it's
> common, i recently had the ignition condenser/capacitor fail. it was
> near short and was weakening the spark considerably. check it while you
> have the distributor open.
>
06-03-2005, 08:14 AM
#10
Guest
Posts: n/a
Re: 91 Civic, no spark
Now I have a second problem, how do I find the FAQ for this place? I'm
using netscape for playing in newsgroups and don't know how to do that!!!!
jim beam wrote:
> Gord wrote:
>
>> Hi all, I need help! Please!?!?!?!
>> 91 Civic dx, 1.5l. TEC distributor (which isn't in the Haynes manual)
>> I've read through the earlier posts on this topic and don't think I've
>> managed to find the problem.
>> This thing cranks and cranks, no go. It has fuel, just no spark.
>> Changed the igniter, still no go. Took the dist. cover off and
>> noticed that the wire to the side of the igniter did not get put on
>> properly by the mech who changed the igniter. Fixed that connection
>> up but still no go. Did we fry the igniter by trying to start it with
>> this wire not getting good contact?
>> Next, checked the coil best I could figure out from the manual which
>> doesn't cover this distributor. Resistance from + to - with the wires
>> disconnected is 1.2 ohms; 12.5 ohms from the + to the tower; 12.9 from
>> - to the tower.
>> Like I said, the Haynes manual doesn't cover a TEC distributor so I
>> don't have reference values to see if this is right for the coil.
>> Also, before I rip it back apart was hoping to hear if we screwed the
>> new igniter in our follies.
>> Thanx a pile, reply to my email too if you don't mind, it's valid.
>> Cheers,
>> Gord
>
>
> is that ohms or k ohms int he coil secondary? if it's ohms, your coil's
> dead.
>
> other than that, don't think you fried the igniter with a bad connection.
>
> better diagnosis is like this;
>
> are you getting signal from the ecu?
> are you getting power to the igniter?
> are you getting power switched from the igniter?
> does the coil spark when you energise & release?
> are you getting spark from the dist cap/rotor assy?
>
> answering each of those questions will determine fault. all the
> individual test methods are described in the faq's or other online sources.
>
> as part of the "power to the igniter" testing, while i don't think it's
> common, i recently had the ignition condenser/capacitor fail. it was
> near short and was weakening the spark considerably. check it while you
> have the distributor open.
>
using netscape for playing in newsgroups and don't know how to do that!!!!
jim beam wrote:
> Gord wrote:
>
>> Hi all, I need help! Please!?!?!?!
>> 91 Civic dx, 1.5l. TEC distributor (which isn't in the Haynes manual)
>> I've read through the earlier posts on this topic and don't think I've
>> managed to find the problem.
>> This thing cranks and cranks, no go. It has fuel, just no spark.
>> Changed the igniter, still no go. Took the dist. cover off and
>> noticed that the wire to the side of the igniter did not get put on
>> properly by the mech who changed the igniter. Fixed that connection
>> up but still no go. Did we fry the igniter by trying to start it with
>> this wire not getting good contact?
>> Next, checked the coil best I could figure out from the manual which
>> doesn't cover this distributor. Resistance from + to - with the wires
>> disconnected is 1.2 ohms; 12.5 ohms from the + to the tower; 12.9 from
>> - to the tower.
>> Like I said, the Haynes manual doesn't cover a TEC distributor so I
>> don't have reference values to see if this is right for the coil.
>> Also, before I rip it back apart was hoping to hear if we screwed the
>> new igniter in our follies.
>> Thanx a pile, reply to my email too if you don't mind, it's valid.
>> Cheers,
>> Gord
>
>
> is that ohms or k ohms int he coil secondary? if it's ohms, your coil's
> dead.
>
> other than that, don't think you fried the igniter with a bad connection.
>
> better diagnosis is like this;
>
> are you getting signal from the ecu?
> are you getting power to the igniter?
> are you getting power switched from the igniter?
> does the coil spark when you energise & release?
> are you getting spark from the dist cap/rotor assy?
>
> answering each of those questions will determine fault. all the
> individual test methods are described in the faq's or other online sources.
>
> as part of the "power to the igniter" testing, while i don't think it's
> common, i recently had the ignition condenser/capacitor fail. it was
> near short and was weakening the spark considerably. check it while you
> have the distributor open.
>
06-03-2005, 08:14 AM
#11
Guest
Posts: n/a
Re: 91 Civic, no spark
Now I have a second problem, how do I find the FAQ for this place? I'm
using netscape for playing in newsgroups and don't know how to do that!!!!
jim beam wrote:
> Gord wrote:
>
>> Hi all, I need help! Please!?!?!?!
>> 91 Civic dx, 1.5l. TEC distributor (which isn't in the Haynes manual)
>> I've read through the earlier posts on this topic and don't think I've
>> managed to find the problem.
>> This thing cranks and cranks, no go. It has fuel, just no spark.
>> Changed the igniter, still no go. Took the dist. cover off and
>> noticed that the wire to the side of the igniter did not get put on
>> properly by the mech who changed the igniter. Fixed that connection
>> up but still no go. Did we fry the igniter by trying to start it with
>> this wire not getting good contact?
>> Next, checked the coil best I could figure out from the manual which
>> doesn't cover this distributor. Resistance from + to - with the wires
>> disconnected is 1.2 ohms; 12.5 ohms from the + to the tower; 12.9 from
>> - to the tower.
>> Like I said, the Haynes manual doesn't cover a TEC distributor so I
>> don't have reference values to see if this is right for the coil.
>> Also, before I rip it back apart was hoping to hear if we screwed the
>> new igniter in our follies.
>> Thanx a pile, reply to my email too if you don't mind, it's valid.
>> Cheers,
>> Gord
>
>
> is that ohms or k ohms int he coil secondary? if it's ohms, your coil's
> dead.
>
> other than that, don't think you fried the igniter with a bad connection.
>
> better diagnosis is like this;
>
> are you getting signal from the ecu?
> are you getting power to the igniter?
> are you getting power switched from the igniter?
> does the coil spark when you energise & release?
> are you getting spark from the dist cap/rotor assy?
>
> answering each of those questions will determine fault. all the
> individual test methods are described in the faq's or other online sources.
>
> as part of the "power to the igniter" testing, while i don't think it's
> common, i recently had the ignition condenser/capacitor fail. it was
> near short and was weakening the spark considerably. check it while you
> have the distributor open.
>
using netscape for playing in newsgroups and don't know how to do that!!!!
jim beam wrote:
> Gord wrote:
>
>> Hi all, I need help! Please!?!?!?!
>> 91 Civic dx, 1.5l. TEC distributor (which isn't in the Haynes manual)
>> I've read through the earlier posts on this topic and don't think I've
>> managed to find the problem.
>> This thing cranks and cranks, no go. It has fuel, just no spark.
>> Changed the igniter, still no go. Took the dist. cover off and
>> noticed that the wire to the side of the igniter did not get put on
>> properly by the mech who changed the igniter. Fixed that connection
>> up but still no go. Did we fry the igniter by trying to start it with
>> this wire not getting good contact?
>> Next, checked the coil best I could figure out from the manual which
>> doesn't cover this distributor. Resistance from + to - with the wires
>> disconnected is 1.2 ohms; 12.5 ohms from the + to the tower; 12.9 from
>> - to the tower.
>> Like I said, the Haynes manual doesn't cover a TEC distributor so I
>> don't have reference values to see if this is right for the coil.
>> Also, before I rip it back apart was hoping to hear if we screwed the
>> new igniter in our follies.
>> Thanx a pile, reply to my email too if you don't mind, it's valid.
>> Cheers,
>> Gord
>
>
> is that ohms or k ohms int he coil secondary? if it's ohms, your coil's
> dead.
>
> other than that, don't think you fried the igniter with a bad connection.
>
> better diagnosis is like this;
>
> are you getting signal from the ecu?
> are you getting power to the igniter?
> are you getting power switched from the igniter?
> does the coil spark when you energise & release?
> are you getting spark from the dist cap/rotor assy?
>
> answering each of those questions will determine fault. all the
> individual test methods are described in the faq's or other online sources.
>
> as part of the "power to the igniter" testing, while i don't think it's
> common, i recently had the ignition condenser/capacitor fail. it was
> near short and was weakening the spark considerably. check it while you
> have the distributor open.
>
06-03-2005, 08:59 AM
#12
Guest
Posts: n/a
Re: 91 Civic, no spark
Gord wrote:
> jim beam wrote:
>
>> Gord wrote:
>>
>>> Hi all, I need help! Please!?!?!?!
>>> 91 Civic dx, 1.5l. TEC distributor (which isn't in the Haynes manual)
>>> I've read through the earlier posts on this topic and don't think
>>> I've managed to find the problem.
>>> This thing cranks and cranks, no go. It has fuel, just no spark.
>>> Changed the igniter, still no go. Took the dist. cover off and
>>> noticed that the wire to the side of the igniter did not get put on
>>> properly by the mech who changed the igniter. Fixed that connection
>>> up but still no go. Did we fry the igniter by trying to start it
>>> with this wire not getting good contact?
>>> Next, checked the coil best I could figure out from the manual which
>>> doesn't cover this distributor. Resistance from + to - with the
>>> wires disconnected is 1.2 ohms; 12.5 ohms from the + to the tower;
>>> 12.9 from - to the tower.
>>> Like I said, the Haynes manual doesn't cover a TEC distributor so I
>>> don't have reference values to see if this is right for the coil.
>>> Also, before I rip it back apart was hoping to hear if we screwed the
>>> new igniter in our follies.
>>> Thanx a pile, reply to my email too if you don't mind, it's valid.
>>> Cheers,
>>> Gord
>>
>>
>>
>> is that ohms or k ohms int he coil secondary? if it's ohms, your
>> coil's dead.
>>
>> other than that, don't think you fried the igniter with a bad connection.
>>
>> better diagnosis is like this;
>>
>> are you getting signal from the ecu?
>> are you getting power to the igniter?
>> are you getting power switched from the igniter?
>> does the coil spark when you energise & release?
>> are you getting spark from the dist cap/rotor assy?
>>
>> answering each of those questions will determine fault. all the
>> individual test methods are described in the faq's or other online
>> sources.
>>
>> as part of the "power to the igniter" testing, while i don't think
>> it's common, i recently had the ignition condenser/capacitor fail. it
>> was near short and was weakening the spark considerably. check it
>> while you have the distributor open.
>>
> Now I have a second problem, how do I find the FAQ for this place? I'm
> using netscape for playing in newsgroups and don't know how to do
that!!!!
>
it's in tegger's signature.
> jim beam wrote:
>
>> Gord wrote:
>>
>>> Hi all, I need help! Please!?!?!?!
>>> 91 Civic dx, 1.5l. TEC distributor (which isn't in the Haynes manual)
>>> I've read through the earlier posts on this topic and don't think
>>> I've managed to find the problem.
>>> This thing cranks and cranks, no go. It has fuel, just no spark.
>>> Changed the igniter, still no go. Took the dist. cover off and
>>> noticed that the wire to the side of the igniter did not get put on
>>> properly by the mech who changed the igniter. Fixed that connection
>>> up but still no go. Did we fry the igniter by trying to start it
>>> with this wire not getting good contact?
>>> Next, checked the coil best I could figure out from the manual which
>>> doesn't cover this distributor. Resistance from + to - with the
>>> wires disconnected is 1.2 ohms; 12.5 ohms from the + to the tower;
>>> 12.9 from - to the tower.
>>> Like I said, the Haynes manual doesn't cover a TEC distributor so I
>>> don't have reference values to see if this is right for the coil.
>>> Also, before I rip it back apart was hoping to hear if we screwed the
>>> new igniter in our follies.
>>> Thanx a pile, reply to my email too if you don't mind, it's valid.
>>> Cheers,
>>> Gord
>>
>>
>>
>> is that ohms or k ohms int he coil secondary? if it's ohms, your
>> coil's dead.
>>
>> other than that, don't think you fried the igniter with a bad connection.
>>
>> better diagnosis is like this;
>>
>> are you getting signal from the ecu?
>> are you getting power to the igniter?
>> are you getting power switched from the igniter?
>> does the coil spark when you energise & release?
>> are you getting spark from the dist cap/rotor assy?
>>
>> answering each of those questions will determine fault. all the
>> individual test methods are described in the faq's or other online
>> sources.
>>
>> as part of the "power to the igniter" testing, while i don't think
>> it's common, i recently had the ignition condenser/capacitor fail. it
>> was near short and was weakening the spark considerably. check it
>> while you have the distributor open.
>>
> Now I have a second problem, how do I find the FAQ for this place? I'm
> using netscape for playing in newsgroups and don't know how to do
that!!!!
>
it's in tegger's signature.
06-03-2005, 08:59 AM
#13
Guest
Posts: n/a
Re: 91 Civic, no spark
Gord wrote:
> jim beam wrote:
>
>> Gord wrote:
>>
>>> Hi all, I need help! Please!?!?!?!
>>> 91 Civic dx, 1.5l. TEC distributor (which isn't in the Haynes manual)
>>> I've read through the earlier posts on this topic and don't think
>>> I've managed to find the problem.
>>> This thing cranks and cranks, no go. It has fuel, just no spark.
>>> Changed the igniter, still no go. Took the dist. cover off and
>>> noticed that the wire to the side of the igniter did not get put on
>>> properly by the mech who changed the igniter. Fixed that connection
>>> up but still no go. Did we fry the igniter by trying to start it
>>> with this wire not getting good contact?
>>> Next, checked the coil best I could figure out from the manual which
>>> doesn't cover this distributor. Resistance from + to - with the
>>> wires disconnected is 1.2 ohms; 12.5 ohms from the + to the tower;
>>> 12.9 from - to the tower.
>>> Like I said, the Haynes manual doesn't cover a TEC distributor so I
>>> don't have reference values to see if this is right for the coil.
>>> Also, before I rip it back apart was hoping to hear if we screwed the
>>> new igniter in our follies.
>>> Thanx a pile, reply to my email too if you don't mind, it's valid.
>>> Cheers,
>>> Gord
>>
>>
>>
>> is that ohms or k ohms int he coil secondary? if it's ohms, your
>> coil's dead.
>>
>> other than that, don't think you fried the igniter with a bad connection.
>>
>> better diagnosis is like this;
>>
>> are you getting signal from the ecu?
>> are you getting power to the igniter?
>> are you getting power switched from the igniter?
>> does the coil spark when you energise & release?
>> are you getting spark from the dist cap/rotor assy?
>>
>> answering each of those questions will determine fault. all the
>> individual test methods are described in the faq's or other online
>> sources.
>>
>> as part of the "power to the igniter" testing, while i don't think
>> it's common, i recently had the ignition condenser/capacitor fail. it
>> was near short and was weakening the spark considerably. check it
>> while you have the distributor open.
>>
> Now I have a second problem, how do I find the FAQ for this place? I'm
> using netscape for playing in newsgroups and don't know how to do
that!!!!
>
it's in tegger's signature.
> jim beam wrote:
>
>> Gord wrote:
>>
>>> Hi all, I need help! Please!?!?!?!
>>> 91 Civic dx, 1.5l. TEC distributor (which isn't in the Haynes manual)
>>> I've read through the earlier posts on this topic and don't think
>>> I've managed to find the problem.
>>> This thing cranks and cranks, no go. It has fuel, just no spark.
>>> Changed the igniter, still no go. Took the dist. cover off and
>>> noticed that the wire to the side of the igniter did not get put on
>>> properly by the mech who changed the igniter. Fixed that connection
>>> up but still no go. Did we fry the igniter by trying to start it
>>> with this wire not getting good contact?
>>> Next, checked the coil best I could figure out from the manual which
>>> doesn't cover this distributor. Resistance from + to - with the
>>> wires disconnected is 1.2 ohms; 12.5 ohms from the + to the tower;
>>> 12.9 from - to the tower.
>>> Like I said, the Haynes manual doesn't cover a TEC distributor so I
>>> don't have reference values to see if this is right for the coil.
>>> Also, before I rip it back apart was hoping to hear if we screwed the
>>> new igniter in our follies.
>>> Thanx a pile, reply to my email too if you don't mind, it's valid.
>>> Cheers,
>>> Gord
>>
>>
>>
>> is that ohms or k ohms int he coil secondary? if it's ohms, your
>> coil's dead.
>>
>> other than that, don't think you fried the igniter with a bad connection.
>>
>> better diagnosis is like this;
>>
>> are you getting signal from the ecu?
>> are you getting power to the igniter?
>> are you getting power switched from the igniter?
>> does the coil spark when you energise & release?
>> are you getting spark from the dist cap/rotor assy?
>>
>> answering each of those questions will determine fault. all the
>> individual test methods are described in the faq's or other online
>> sources.
>>
>> as part of the "power to the igniter" testing, while i don't think
>> it's common, i recently had the ignition condenser/capacitor fail. it
>> was near short and was weakening the spark considerably. check it
>> while you have the distributor open.
>>
> Now I have a second problem, how do I find the FAQ for this place? I'm
> using netscape for playing in newsgroups and don't know how to do
that!!!!
>
it's in tegger's signature.
06-03-2005, 09:51 AM
#14
Guest
Posts: n/a
Re: 91 Civic, no spark
jim beam <nospam@example.net> wrote in
news:h5KdnfUFRdwYJgLfRVn-jg@speakeasy.net:
> as part of the "power to the igniter" testing, while i don't think
> it's common, i recently had the ignition condenser/capacitor fail. it
> was near short and was weakening the spark considerably. check it
> while you have the distributor open.
>
Where did you find this condenser? It's not the RF cap is it?
--
TeGGeR®
The Unofficial Honda/Acura FAQ
www.tegger.com/hondafaq/
news:h5KdnfUFRdwYJgLfRVn-jg@speakeasy.net:
> as part of the "power to the igniter" testing, while i don't think
> it's common, i recently had the ignition condenser/capacitor fail. it
> was near short and was weakening the spark considerably. check it
> while you have the distributor open.
>
Where did you find this condenser? It's not the RF cap is it?
--
TeGGeR®
The Unofficial Honda/Acura FAQ
www.tegger.com/hondafaq/
06-03-2005, 09:51 AM
#15
Guest
Posts: n/a
Re: 91 Civic, no spark
jim beam <nospam@example.net> wrote in
news:h5KdnfUFRdwYJgLfRVn-jg@speakeasy.net:
> as part of the "power to the igniter" testing, while i don't think
> it's common, i recently had the ignition condenser/capacitor fail. it
> was near short and was weakening the spark considerably. check it
> while you have the distributor open.
>
Where did you find this condenser? It's not the RF cap is it?
--
TeGGeR®
The Unofficial Honda/Acura FAQ
www.tegger.com/hondafaq/
news:h5KdnfUFRdwYJgLfRVn-jg@speakeasy.net:
> as part of the "power to the igniter" testing, while i don't think
> it's common, i recently had the ignition condenser/capacitor fail. it
> was near short and was weakening the spark considerably. check it
> while you have the distributor open.
>
Where did you find this condenser? It's not the RF cap is it?
--
TeGGeR®
The Unofficial Honda/Acura FAQ
www.tegger.com/hondafaq/