Buying a replacement engine
12-30-2006, 11:16 PM
#16
Guest
Posts: n/a
Re: Buying a replacement engine
larson.joshua@gmail.com wrote:
> i've done some looking online and it's difficult to discern what's what
> and if a given website is legitimate. that's the biggest difficulty.
the biggest thing is to buy with a credit card [not debit card]. that
way, ultimately, if there's a problem, the vendor has to work with you
and the credit card company to resolve any problems. i'd just go for
one of the direct jdm importers with as low a mileage as possible. you
don't need much of a warranty - say a month. if it works, has no head
problems and doesn't burn oil, you're set - all those will be detectable
in the first week or so.
>
> jim - you've helped me in the past and i appreciate that. here's the
> long story short: bought the car from a friend. when i bought it, it
> probably had a blown head gasket. after a while, the engine blew,
> overheated severely and i had head reworked. i did the work and
> installed new timing belt, new water pump, and of course new head
> gasket.
>
> the engine seemed to run just okay. it felt tired. then the temp
> started fluctuating. replaced thermostat a few times, rad cap a few
> times... was losing coolant. figured i messed up first gasket job.
> started #2. replaced timing belt, head gasket had head reworked.
> replaced distributor after the last one had bad crank sensor (caught
> warranty by a week!).
>
> car runs okay, but here's the thing it did after 1st and 2nd head
> gasket job: after i drive for a while, some kind of gas gets into the
> cooling system. it bubbles, not boils, pretty vigorously after i come
> home (up a mountainside). i could live with this, but i have to check
> the fluid levels every couple days now. the gas pushes coolant out,
> overflows the resevoir, makes a mess and then i have to fill it back
> up.
something's cracked.
>
> i am now feeling like the block is cracked or something else is majorly
> messed up. plus, i'm a little sick of working on this engine...
replacement is 100% the way to go - not worth wasting another single
moment on that motor. onwards!
>
>
> jim beam wrote:
>> larson.joshua@gmail.com wrote:
>>> i'm considering replacing the engine in my 1991 civic DX - i think it
>>> is a D15B2.
>>>
>>> i think i want just a straight replacement. i'm more interested in
>>> fuel economy than performance.
>>>
>>> does anyone have any experience or advice regarding purchasing engines?
>>> i need practical information regarding JDM engines, buying online and
>>> warranties.
>>>
>>> thanks!
>>>
>> what's wrong with yours and why do you want to replace it? how many
>> miles? i ask because if you think it's not performing right, there are
>> a number of possible causes, all of which are cheaper and less
>> troublesome than replacing the whole unit.
>
> i've done some looking online and it's difficult to discern what's what
> and if a given website is legitimate. that's the biggest difficulty.
the biggest thing is to buy with a credit card [not debit card]. that
way, ultimately, if there's a problem, the vendor has to work with you
and the credit card company to resolve any problems. i'd just go for
one of the direct jdm importers with as low a mileage as possible. you
don't need much of a warranty - say a month. if it works, has no head
problems and doesn't burn oil, you're set - all those will be detectable
in the first week or so.
>
> jim - you've helped me in the past and i appreciate that. here's the
> long story short: bought the car from a friend. when i bought it, it
> probably had a blown head gasket. after a while, the engine blew,
> overheated severely and i had head reworked. i did the work and
> installed new timing belt, new water pump, and of course new head
> gasket.
>
> the engine seemed to run just okay. it felt tired. then the temp
> started fluctuating. replaced thermostat a few times, rad cap a few
> times... was losing coolant. figured i messed up first gasket job.
> started #2. replaced timing belt, head gasket had head reworked.
> replaced distributor after the last one had bad crank sensor (caught
> warranty by a week!).
>
> car runs okay, but here's the thing it did after 1st and 2nd head
> gasket job: after i drive for a while, some kind of gas gets into the
> cooling system. it bubbles, not boils, pretty vigorously after i come
> home (up a mountainside). i could live with this, but i have to check
> the fluid levels every couple days now. the gas pushes coolant out,
> overflows the resevoir, makes a mess and then i have to fill it back
> up.
something's cracked.
>
> i am now feeling like the block is cracked or something else is majorly
> messed up. plus, i'm a little sick of working on this engine...
replacement is 100% the way to go - not worth wasting another single
moment on that motor. onwards!
>
>
> jim beam wrote:
>> larson.joshua@gmail.com wrote:
>>> i'm considering replacing the engine in my 1991 civic DX - i think it
>>> is a D15B2.
>>>
>>> i think i want just a straight replacement. i'm more interested in
>>> fuel economy than performance.
>>>
>>> does anyone have any experience or advice regarding purchasing engines?
>>> i need practical information regarding JDM engines, buying online and
>>> warranties.
>>>
>>> thanks!
>>>
>> what's wrong with yours and why do you want to replace it? how many
>> miles? i ask because if you think it's not performing right, there are
>> a number of possible causes, all of which are cheaper and less
>> troublesome than replacing the whole unit.
>
12-30-2006, 11:16 PM
#17
Guest
Posts: n/a
Re: Buying a replacement engine
larson.joshua@gmail.com wrote:
> i've done some looking online and it's difficult to discern what's what
> and if a given website is legitimate. that's the biggest difficulty.
the biggest thing is to buy with a credit card [not debit card]. that
way, ultimately, if there's a problem, the vendor has to work with you
and the credit card company to resolve any problems. i'd just go for
one of the direct jdm importers with as low a mileage as possible. you
don't need much of a warranty - say a month. if it works, has no head
problems and doesn't burn oil, you're set - all those will be detectable
in the first week or so.
>
> jim - you've helped me in the past and i appreciate that. here's the
> long story short: bought the car from a friend. when i bought it, it
> probably had a blown head gasket. after a while, the engine blew,
> overheated severely and i had head reworked. i did the work and
> installed new timing belt, new water pump, and of course new head
> gasket.
>
> the engine seemed to run just okay. it felt tired. then the temp
> started fluctuating. replaced thermostat a few times, rad cap a few
> times... was losing coolant. figured i messed up first gasket job.
> started #2. replaced timing belt, head gasket had head reworked.
> replaced distributor after the last one had bad crank sensor (caught
> warranty by a week!).
>
> car runs okay, but here's the thing it did after 1st and 2nd head
> gasket job: after i drive for a while, some kind of gas gets into the
> cooling system. it bubbles, not boils, pretty vigorously after i come
> home (up a mountainside). i could live with this, but i have to check
> the fluid levels every couple days now. the gas pushes coolant out,
> overflows the resevoir, makes a mess and then i have to fill it back
> up.
something's cracked.
>
> i am now feeling like the block is cracked or something else is majorly
> messed up. plus, i'm a little sick of working on this engine...
replacement is 100% the way to go - not worth wasting another single
moment on that motor. onwards!
>
>
> jim beam wrote:
>> larson.joshua@gmail.com wrote:
>>> i'm considering replacing the engine in my 1991 civic DX - i think it
>>> is a D15B2.
>>>
>>> i think i want just a straight replacement. i'm more interested in
>>> fuel economy than performance.
>>>
>>> does anyone have any experience or advice regarding purchasing engines?
>>> i need practical information regarding JDM engines, buying online and
>>> warranties.
>>>
>>> thanks!
>>>
>> what's wrong with yours and why do you want to replace it? how many
>> miles? i ask because if you think it's not performing right, there are
>> a number of possible causes, all of which are cheaper and less
>> troublesome than replacing the whole unit.
>
> i've done some looking online and it's difficult to discern what's what
> and if a given website is legitimate. that's the biggest difficulty.
the biggest thing is to buy with a credit card [not debit card]. that
way, ultimately, if there's a problem, the vendor has to work with you
and the credit card company to resolve any problems. i'd just go for
one of the direct jdm importers with as low a mileage as possible. you
don't need much of a warranty - say a month. if it works, has no head
problems and doesn't burn oil, you're set - all those will be detectable
in the first week or so.
>
> jim - you've helped me in the past and i appreciate that. here's the
> long story short: bought the car from a friend. when i bought it, it
> probably had a blown head gasket. after a while, the engine blew,
> overheated severely and i had head reworked. i did the work and
> installed new timing belt, new water pump, and of course new head
> gasket.
>
> the engine seemed to run just okay. it felt tired. then the temp
> started fluctuating. replaced thermostat a few times, rad cap a few
> times... was losing coolant. figured i messed up first gasket job.
> started #2. replaced timing belt, head gasket had head reworked.
> replaced distributor after the last one had bad crank sensor (caught
> warranty by a week!).
>
> car runs okay, but here's the thing it did after 1st and 2nd head
> gasket job: after i drive for a while, some kind of gas gets into the
> cooling system. it bubbles, not boils, pretty vigorously after i come
> home (up a mountainside). i could live with this, but i have to check
> the fluid levels every couple days now. the gas pushes coolant out,
> overflows the resevoir, makes a mess and then i have to fill it back
> up.
something's cracked.
>
> i am now feeling like the block is cracked or something else is majorly
> messed up. plus, i'm a little sick of working on this engine...
replacement is 100% the way to go - not worth wasting another single
moment on that motor. onwards!
>
>
> jim beam wrote:
>> larson.joshua@gmail.com wrote:
>>> i'm considering replacing the engine in my 1991 civic DX - i think it
>>> is a D15B2.
>>>
>>> i think i want just a straight replacement. i'm more interested in
>>> fuel economy than performance.
>>>
>>> does anyone have any experience or advice regarding purchasing engines?
>>> i need practical information regarding JDM engines, buying online and
>>> warranties.
>>>
>>> thanks!
>>>
>> what's wrong with yours and why do you want to replace it? how many
>> miles? i ask because if you think it's not performing right, there are
>> a number of possible causes, all of which are cheaper and less
>> troublesome than replacing the whole unit.
>
12-30-2006, 11:30 PM
#18
Guest
Posts: n/a
Re: Buying a replacement engine
thanks jim,
i appreciate your help! do you know of any reputable vendors of these
jdm motors? you mentioned "one of the direct jdm importers."
also, is this industry legit? as in, are the mileages they quote for
real or is it just B.S.? would i be better off going to the junk yard?
thanks again (exciting saturday, right?).
jim beam wrote:
> larson.joshua@gmail.com wrote:
> > i've done some looking online and it's difficult to discern what's what
> > and if a given website is legitimate. that's the biggest difficulty.
>
> the biggest thing is to buy with a credit card [not debit card]. that
> way, ultimately, if there's a problem, the vendor has to work with you
> and the credit card company to resolve any problems. i'd just go for
> one of the direct jdm importers with as low a mileage as possible. you
> don't need much of a warranty - say a month. if it works, has no head
> problems and doesn't burn oil, you're set - all those will be detectable
> in the first week or so.
>
> >
> > jim - you've helped me in the past and i appreciate that. here's the
> > long story short: bought the car from a friend. when i bought it, it
> > probably had a blown head gasket. after a while, the engine blew,
> > overheated severely and i had head reworked. i did the work and
> > installed new timing belt, new water pump, and of course new head
> > gasket.
> >
> > the engine seemed to run just okay. it felt tired. then the temp
> > started fluctuating. replaced thermostat a few times, rad cap a few
> > times... was losing coolant. figured i messed up first gasket job.
> > started #2. replaced timing belt, head gasket had head reworked.
> > replaced distributor after the last one had bad crank sensor (caught
> > warranty by a week!).
> >
> > car runs okay, but here's the thing it did after 1st and 2nd head
> > gasket job: after i drive for a while, some kind of gas gets into the
> > cooling system. it bubbles, not boils, pretty vigorously after i come
> > home (up a mountainside). i could live with this, but i have to check
> > the fluid levels every couple days now. the gas pushes coolant out,
> > overflows the resevoir, makes a mess and then i have to fill it back
> > up.
>
> something's cracked.
>
> >
> > i am now feeling like the block is cracked or something else is majorly
> > messed up. plus, i'm a little sick of working on this engine...
>
> replacement is 100% the way to go - not worth wasting another single
> moment on that motor. onwards!
>
> >
> >
> > jim beam wrote:
> >> larson.joshua@gmail.com wrote:
> >>> i'm considering replacing the engine in my 1991 civic DX - i think it
> >>> is a D15B2.
> >>>
> >>> i think i want just a straight replacement. i'm more interested in
> >>> fuel economy than performance.
> >>>
> >>> does anyone have any experience or advice regarding purchasing engines?
> >>> i need practical information regarding JDM engines, buying online and
> >>> warranties.
> >>>
> >>> thanks!
> >>>
> >> what's wrong with yours and why do you want to replace it? how many
> >> miles? i ask because if you think it's not performing right, there are
> >> a number of possible causes, all of which are cheaper and less
> >> troublesome than replacing the whole unit.
> >
i appreciate your help! do you know of any reputable vendors of these
jdm motors? you mentioned "one of the direct jdm importers."
also, is this industry legit? as in, are the mileages they quote for
real or is it just B.S.? would i be better off going to the junk yard?
thanks again (exciting saturday, right?).
jim beam wrote:
> larson.joshua@gmail.com wrote:
> > i've done some looking online and it's difficult to discern what's what
> > and if a given website is legitimate. that's the biggest difficulty.
>
> the biggest thing is to buy with a credit card [not debit card]. that
> way, ultimately, if there's a problem, the vendor has to work with you
> and the credit card company to resolve any problems. i'd just go for
> one of the direct jdm importers with as low a mileage as possible. you
> don't need much of a warranty - say a month. if it works, has no head
> problems and doesn't burn oil, you're set - all those will be detectable
> in the first week or so.
>
> >
> > jim - you've helped me in the past and i appreciate that. here's the
> > long story short: bought the car from a friend. when i bought it, it
> > probably had a blown head gasket. after a while, the engine blew,
> > overheated severely and i had head reworked. i did the work and
> > installed new timing belt, new water pump, and of course new head
> > gasket.
> >
> > the engine seemed to run just okay. it felt tired. then the temp
> > started fluctuating. replaced thermostat a few times, rad cap a few
> > times... was losing coolant. figured i messed up first gasket job.
> > started #2. replaced timing belt, head gasket had head reworked.
> > replaced distributor after the last one had bad crank sensor (caught
> > warranty by a week!).
> >
> > car runs okay, but here's the thing it did after 1st and 2nd head
> > gasket job: after i drive for a while, some kind of gas gets into the
> > cooling system. it bubbles, not boils, pretty vigorously after i come
> > home (up a mountainside). i could live with this, but i have to check
> > the fluid levels every couple days now. the gas pushes coolant out,
> > overflows the resevoir, makes a mess and then i have to fill it back
> > up.
>
> something's cracked.
>
> >
> > i am now feeling like the block is cracked or something else is majorly
> > messed up. plus, i'm a little sick of working on this engine...
>
> replacement is 100% the way to go - not worth wasting another single
> moment on that motor. onwards!
>
> >
> >
> > jim beam wrote:
> >> larson.joshua@gmail.com wrote:
> >>> i'm considering replacing the engine in my 1991 civic DX - i think it
> >>> is a D15B2.
> >>>
> >>> i think i want just a straight replacement. i'm more interested in
> >>> fuel economy than performance.
> >>>
> >>> does anyone have any experience or advice regarding purchasing engines?
> >>> i need practical information regarding JDM engines, buying online and
> >>> warranties.
> >>>
> >>> thanks!
> >>>
> >> what's wrong with yours and why do you want to replace it? how many
> >> miles? i ask because if you think it's not performing right, there are
> >> a number of possible causes, all of which are cheaper and less
> >> troublesome than replacing the whole unit.
> >
12-30-2006, 11:30 PM
#19
Guest
Posts: n/a
Re: Buying a replacement engine
thanks jim,
i appreciate your help! do you know of any reputable vendors of these
jdm motors? you mentioned "one of the direct jdm importers."
also, is this industry legit? as in, are the mileages they quote for
real or is it just B.S.? would i be better off going to the junk yard?
thanks again (exciting saturday, right?).
jim beam wrote:
> larson.joshua@gmail.com wrote:
> > i've done some looking online and it's difficult to discern what's what
> > and if a given website is legitimate. that's the biggest difficulty.
>
> the biggest thing is to buy with a credit card [not debit card]. that
> way, ultimately, if there's a problem, the vendor has to work with you
> and the credit card company to resolve any problems. i'd just go for
> one of the direct jdm importers with as low a mileage as possible. you
> don't need much of a warranty - say a month. if it works, has no head
> problems and doesn't burn oil, you're set - all those will be detectable
> in the first week or so.
>
> >
> > jim - you've helped me in the past and i appreciate that. here's the
> > long story short: bought the car from a friend. when i bought it, it
> > probably had a blown head gasket. after a while, the engine blew,
> > overheated severely and i had head reworked. i did the work and
> > installed new timing belt, new water pump, and of course new head
> > gasket.
> >
> > the engine seemed to run just okay. it felt tired. then the temp
> > started fluctuating. replaced thermostat a few times, rad cap a few
> > times... was losing coolant. figured i messed up first gasket job.
> > started #2. replaced timing belt, head gasket had head reworked.
> > replaced distributor after the last one had bad crank sensor (caught
> > warranty by a week!).
> >
> > car runs okay, but here's the thing it did after 1st and 2nd head
> > gasket job: after i drive for a while, some kind of gas gets into the
> > cooling system. it bubbles, not boils, pretty vigorously after i come
> > home (up a mountainside). i could live with this, but i have to check
> > the fluid levels every couple days now. the gas pushes coolant out,
> > overflows the resevoir, makes a mess and then i have to fill it back
> > up.
>
> something's cracked.
>
> >
> > i am now feeling like the block is cracked or something else is majorly
> > messed up. plus, i'm a little sick of working on this engine...
>
> replacement is 100% the way to go - not worth wasting another single
> moment on that motor. onwards!
>
> >
> >
> > jim beam wrote:
> >> larson.joshua@gmail.com wrote:
> >>> i'm considering replacing the engine in my 1991 civic DX - i think it
> >>> is a D15B2.
> >>>
> >>> i think i want just a straight replacement. i'm more interested in
> >>> fuel economy than performance.
> >>>
> >>> does anyone have any experience or advice regarding purchasing engines?
> >>> i need practical information regarding JDM engines, buying online and
> >>> warranties.
> >>>
> >>> thanks!
> >>>
> >> what's wrong with yours and why do you want to replace it? how many
> >> miles? i ask because if you think it's not performing right, there are
> >> a number of possible causes, all of which are cheaper and less
> >> troublesome than replacing the whole unit.
> >
i appreciate your help! do you know of any reputable vendors of these
jdm motors? you mentioned "one of the direct jdm importers."
also, is this industry legit? as in, are the mileages they quote for
real or is it just B.S.? would i be better off going to the junk yard?
thanks again (exciting saturday, right?).
jim beam wrote:
> larson.joshua@gmail.com wrote:
> > i've done some looking online and it's difficult to discern what's what
> > and if a given website is legitimate. that's the biggest difficulty.
>
> the biggest thing is to buy with a credit card [not debit card]. that
> way, ultimately, if there's a problem, the vendor has to work with you
> and the credit card company to resolve any problems. i'd just go for
> one of the direct jdm importers with as low a mileage as possible. you
> don't need much of a warranty - say a month. if it works, has no head
> problems and doesn't burn oil, you're set - all those will be detectable
> in the first week or so.
>
> >
> > jim - you've helped me in the past and i appreciate that. here's the
> > long story short: bought the car from a friend. when i bought it, it
> > probably had a blown head gasket. after a while, the engine blew,
> > overheated severely and i had head reworked. i did the work and
> > installed new timing belt, new water pump, and of course new head
> > gasket.
> >
> > the engine seemed to run just okay. it felt tired. then the temp
> > started fluctuating. replaced thermostat a few times, rad cap a few
> > times... was losing coolant. figured i messed up first gasket job.
> > started #2. replaced timing belt, head gasket had head reworked.
> > replaced distributor after the last one had bad crank sensor (caught
> > warranty by a week!).
> >
> > car runs okay, but here's the thing it did after 1st and 2nd head
> > gasket job: after i drive for a while, some kind of gas gets into the
> > cooling system. it bubbles, not boils, pretty vigorously after i come
> > home (up a mountainside). i could live with this, but i have to check
> > the fluid levels every couple days now. the gas pushes coolant out,
> > overflows the resevoir, makes a mess and then i have to fill it back
> > up.
>
> something's cracked.
>
> >
> > i am now feeling like the block is cracked or something else is majorly
> > messed up. plus, i'm a little sick of working on this engine...
>
> replacement is 100% the way to go - not worth wasting another single
> moment on that motor. onwards!
>
> >
> >
> > jim beam wrote:
> >> larson.joshua@gmail.com wrote:
> >>> i'm considering replacing the engine in my 1991 civic DX - i think it
> >>> is a D15B2.
> >>>
> >>> i think i want just a straight replacement. i'm more interested in
> >>> fuel economy than performance.
> >>>
> >>> does anyone have any experience or advice regarding purchasing engines?
> >>> i need practical information regarding JDM engines, buying online and
> >>> warranties.
> >>>
> >>> thanks!
> >>>
> >> what's wrong with yours and why do you want to replace it? how many
> >> miles? i ask because if you think it's not performing right, there are
> >> a number of possible causes, all of which are cheaper and less
> >> troublesome than replacing the whole unit.
> >
12-30-2006, 11:30 PM
#20
Guest
Posts: n/a
Re: Buying a replacement engine
thanks jim,
i appreciate your help! do you know of any reputable vendors of these
jdm motors? you mentioned "one of the direct jdm importers."
also, is this industry legit? as in, are the mileages they quote for
real or is it just B.S.? would i be better off going to the junk yard?
thanks again (exciting saturday, right?).
jim beam wrote:
> larson.joshua@gmail.com wrote:
> > i've done some looking online and it's difficult to discern what's what
> > and if a given website is legitimate. that's the biggest difficulty.
>
> the biggest thing is to buy with a credit card [not debit card]. that
> way, ultimately, if there's a problem, the vendor has to work with you
> and the credit card company to resolve any problems. i'd just go for
> one of the direct jdm importers with as low a mileage as possible. you
> don't need much of a warranty - say a month. if it works, has no head
> problems and doesn't burn oil, you're set - all those will be detectable
> in the first week or so.
>
> >
> > jim - you've helped me in the past and i appreciate that. here's the
> > long story short: bought the car from a friend. when i bought it, it
> > probably had a blown head gasket. after a while, the engine blew,
> > overheated severely and i had head reworked. i did the work and
> > installed new timing belt, new water pump, and of course new head
> > gasket.
> >
> > the engine seemed to run just okay. it felt tired. then the temp
> > started fluctuating. replaced thermostat a few times, rad cap a few
> > times... was losing coolant. figured i messed up first gasket job.
> > started #2. replaced timing belt, head gasket had head reworked.
> > replaced distributor after the last one had bad crank sensor (caught
> > warranty by a week!).
> >
> > car runs okay, but here's the thing it did after 1st and 2nd head
> > gasket job: after i drive for a while, some kind of gas gets into the
> > cooling system. it bubbles, not boils, pretty vigorously after i come
> > home (up a mountainside). i could live with this, but i have to check
> > the fluid levels every couple days now. the gas pushes coolant out,
> > overflows the resevoir, makes a mess and then i have to fill it back
> > up.
>
> something's cracked.
>
> >
> > i am now feeling like the block is cracked or something else is majorly
> > messed up. plus, i'm a little sick of working on this engine...
>
> replacement is 100% the way to go - not worth wasting another single
> moment on that motor. onwards!
>
> >
> >
> > jim beam wrote:
> >> larson.joshua@gmail.com wrote:
> >>> i'm considering replacing the engine in my 1991 civic DX - i think it
> >>> is a D15B2.
> >>>
> >>> i think i want just a straight replacement. i'm more interested in
> >>> fuel economy than performance.
> >>>
> >>> does anyone have any experience or advice regarding purchasing engines?
> >>> i need practical information regarding JDM engines, buying online and
> >>> warranties.
> >>>
> >>> thanks!
> >>>
> >> what's wrong with yours and why do you want to replace it? how many
> >> miles? i ask because if you think it's not performing right, there are
> >> a number of possible causes, all of which are cheaper and less
> >> troublesome than replacing the whole unit.
> >
i appreciate your help! do you know of any reputable vendors of these
jdm motors? you mentioned "one of the direct jdm importers."
also, is this industry legit? as in, are the mileages they quote for
real or is it just B.S.? would i be better off going to the junk yard?
thanks again (exciting saturday, right?).
jim beam wrote:
> larson.joshua@gmail.com wrote:
> > i've done some looking online and it's difficult to discern what's what
> > and if a given website is legitimate. that's the biggest difficulty.
>
> the biggest thing is to buy with a credit card [not debit card]. that
> way, ultimately, if there's a problem, the vendor has to work with you
> and the credit card company to resolve any problems. i'd just go for
> one of the direct jdm importers with as low a mileage as possible. you
> don't need much of a warranty - say a month. if it works, has no head
> problems and doesn't burn oil, you're set - all those will be detectable
> in the first week or so.
>
> >
> > jim - you've helped me in the past and i appreciate that. here's the
> > long story short: bought the car from a friend. when i bought it, it
> > probably had a blown head gasket. after a while, the engine blew,
> > overheated severely and i had head reworked. i did the work and
> > installed new timing belt, new water pump, and of course new head
> > gasket.
> >
> > the engine seemed to run just okay. it felt tired. then the temp
> > started fluctuating. replaced thermostat a few times, rad cap a few
> > times... was losing coolant. figured i messed up first gasket job.
> > started #2. replaced timing belt, head gasket had head reworked.
> > replaced distributor after the last one had bad crank sensor (caught
> > warranty by a week!).
> >
> > car runs okay, but here's the thing it did after 1st and 2nd head
> > gasket job: after i drive for a while, some kind of gas gets into the
> > cooling system. it bubbles, not boils, pretty vigorously after i come
> > home (up a mountainside). i could live with this, but i have to check
> > the fluid levels every couple days now. the gas pushes coolant out,
> > overflows the resevoir, makes a mess and then i have to fill it back
> > up.
>
> something's cracked.
>
> >
> > i am now feeling like the block is cracked or something else is majorly
> > messed up. plus, i'm a little sick of working on this engine...
>
> replacement is 100% the way to go - not worth wasting another single
> moment on that motor. onwards!
>
> >
> >
> > jim beam wrote:
> >> larson.joshua@gmail.com wrote:
> >>> i'm considering replacing the engine in my 1991 civic DX - i think it
> >>> is a D15B2.
> >>>
> >>> i think i want just a straight replacement. i'm more interested in
> >>> fuel economy than performance.
> >>>
> >>> does anyone have any experience or advice regarding purchasing engines?
> >>> i need practical information regarding JDM engines, buying online and
> >>> warranties.
> >>>
> >>> thanks!
> >>>
> >> what's wrong with yours and why do you want to replace it? how many
> >> miles? i ask because if you think it's not performing right, there are
> >> a number of possible causes, all of which are cheaper and less
> >> troublesome than replacing the whole unit.
> >
12-30-2006, 11:49 PM
#21
Guest
Posts: n/a
Re: Buying a replacement engine
larson.joshua@gmail.com wrote:
> thanks jim,
>
> i appreciate your help! do you know of any reputable vendors of these
> jdm motors? you mentioned "one of the direct jdm importers."
>
> also, is this industry legit? as in, are the mileages they quote for
> real or is it just B.S.? would i be better off going to the junk yard?
no, it's legit. mileages should be about right - other markets,
particularly japan, do much lower mileage than us. that's why i'd only
buy a domestic motor in emergency - /much/ higher mileage. but that
said, there's no reason a d15 can't do 300k miles if it's not been
cracked and has had the oil changed regularly.
i'm not endorsing any of the following:
http://www.sunrisejdmmotors.com/
http://www.nippon-motors.com/honda.htm
http://www.naganojapanese.com/
there are a bunch of others if you google.
good luck!
>
> thanks again (exciting saturday, right?).
you're not going anywhere with that motor!
>
> jim beam wrote:
>> larson.joshua@gmail.com wrote:
>>> i've done some looking online and it's difficult to discern what's what
>>> and if a given website is legitimate. that's the biggest difficulty.
>> the biggest thing is to buy with a credit card [not debit card]. that
>> way, ultimately, if there's a problem, the vendor has to work with you
>> and the credit card company to resolve any problems. i'd just go for
>> one of the direct jdm importers with as low a mileage as possible. you
>> don't need much of a warranty - say a month. if it works, has no head
>> problems and doesn't burn oil, you're set - all those will be detectable
>> in the first week or so.
>>
>>> jim - you've helped me in the past and i appreciate that. here's the
>>> long story short: bought the car from a friend. when i bought it, it
>>> probably had a blown head gasket. after a while, the engine blew,
>>> overheated severely and i had head reworked. i did the work and
>>> installed new timing belt, new water pump, and of course new head
>>> gasket.
>>>
>>> the engine seemed to run just okay. it felt tired. then the temp
>>> started fluctuating. replaced thermostat a few times, rad cap a few
>>> times... was losing coolant. figured i messed up first gasket job.
>>> started #2. replaced timing belt, head gasket had head reworked.
>>> replaced distributor after the last one had bad crank sensor (caught
>>> warranty by a week!).
>>>
>>> car runs okay, but here's the thing it did after 1st and 2nd head
>>> gasket job: after i drive for a while, some kind of gas gets into the
>>> cooling system. it bubbles, not boils, pretty vigorously after i come
>>> home (up a mountainside). i could live with this, but i have to check
>>> the fluid levels every couple days now. the gas pushes coolant out,
>>> overflows the resevoir, makes a mess and then i have to fill it back
>>> up.
>> something's cracked.
>>
>>> i am now feeling like the block is cracked or something else is majorly
>>> messed up. plus, i'm a little sick of working on this engine...
>> replacement is 100% the way to go - not worth wasting another single
>> moment on that motor. onwards!
>>
>>>
>>> jim beam wrote:
>>>> larson.joshua@gmail.com wrote:
>>>>> i'm considering replacing the engine in my 1991 civic DX - i think it
>>>>> is a D15B2.
>>>>>
>>>>> i think i want just a straight replacement. i'm more interested in
>>>>> fuel economy than performance.
>>>>>
>>>>> does anyone have any experience or advice regarding purchasing engines?
>>>>> i need practical information regarding JDM engines, buying online and
>>>>> warranties.
>>>>>
>>>>> thanks!
>>>>>
>>>> what's wrong with yours and why do you want to replace it? how many
>>>> miles? i ask because if you think it's not performing right, there are
>>>> a number of possible causes, all of which are cheaper and less
>>>> troublesome than replacing the whole unit.
>
> thanks jim,
>
> i appreciate your help! do you know of any reputable vendors of these
> jdm motors? you mentioned "one of the direct jdm importers."
>
> also, is this industry legit? as in, are the mileages they quote for
> real or is it just B.S.? would i be better off going to the junk yard?
no, it's legit. mileages should be about right - other markets,
particularly japan, do much lower mileage than us. that's why i'd only
buy a domestic motor in emergency - /much/ higher mileage. but that
said, there's no reason a d15 can't do 300k miles if it's not been
cracked and has had the oil changed regularly.
i'm not endorsing any of the following:
http://www.sunrisejdmmotors.com/
http://www.nippon-motors.com/honda.htm
http://www.naganojapanese.com/
there are a bunch of others if you google.
good luck!
>
> thanks again (exciting saturday, right?).
you're not going anywhere with that motor!
>
> jim beam wrote:
>> larson.joshua@gmail.com wrote:
>>> i've done some looking online and it's difficult to discern what's what
>>> and if a given website is legitimate. that's the biggest difficulty.
>> the biggest thing is to buy with a credit card [not debit card]. that
>> way, ultimately, if there's a problem, the vendor has to work with you
>> and the credit card company to resolve any problems. i'd just go for
>> one of the direct jdm importers with as low a mileage as possible. you
>> don't need much of a warranty - say a month. if it works, has no head
>> problems and doesn't burn oil, you're set - all those will be detectable
>> in the first week or so.
>>
>>> jim - you've helped me in the past and i appreciate that. here's the
>>> long story short: bought the car from a friend. when i bought it, it
>>> probably had a blown head gasket. after a while, the engine blew,
>>> overheated severely and i had head reworked. i did the work and
>>> installed new timing belt, new water pump, and of course new head
>>> gasket.
>>>
>>> the engine seemed to run just okay. it felt tired. then the temp
>>> started fluctuating. replaced thermostat a few times, rad cap a few
>>> times... was losing coolant. figured i messed up first gasket job.
>>> started #2. replaced timing belt, head gasket had head reworked.
>>> replaced distributor after the last one had bad crank sensor (caught
>>> warranty by a week!).
>>>
>>> car runs okay, but here's the thing it did after 1st and 2nd head
>>> gasket job: after i drive for a while, some kind of gas gets into the
>>> cooling system. it bubbles, not boils, pretty vigorously after i come
>>> home (up a mountainside). i could live with this, but i have to check
>>> the fluid levels every couple days now. the gas pushes coolant out,
>>> overflows the resevoir, makes a mess and then i have to fill it back
>>> up.
>> something's cracked.
>>
>>> i am now feeling like the block is cracked or something else is majorly
>>> messed up. plus, i'm a little sick of working on this engine...
>> replacement is 100% the way to go - not worth wasting another single
>> moment on that motor. onwards!
>>
>>>
>>> jim beam wrote:
>>>> larson.joshua@gmail.com wrote:
>>>>> i'm considering replacing the engine in my 1991 civic DX - i think it
>>>>> is a D15B2.
>>>>>
>>>>> i think i want just a straight replacement. i'm more interested in
>>>>> fuel economy than performance.
>>>>>
>>>>> does anyone have any experience or advice regarding purchasing engines?
>>>>> i need practical information regarding JDM engines, buying online and
>>>>> warranties.
>>>>>
>>>>> thanks!
>>>>>
>>>> what's wrong with yours and why do you want to replace it? how many
>>>> miles? i ask because if you think it's not performing right, there are
>>>> a number of possible causes, all of which are cheaper and less
>>>> troublesome than replacing the whole unit.
>
12-30-2006, 11:49 PM
#22
Guest
Posts: n/a
Re: Buying a replacement engine
larson.joshua@gmail.com wrote:
> thanks jim,
>
> i appreciate your help! do you know of any reputable vendors of these
> jdm motors? you mentioned "one of the direct jdm importers."
>
> also, is this industry legit? as in, are the mileages they quote for
> real or is it just B.S.? would i be better off going to the junk yard?
no, it's legit. mileages should be about right - other markets,
particularly japan, do much lower mileage than us. that's why i'd only
buy a domestic motor in emergency - /much/ higher mileage. but that
said, there's no reason a d15 can't do 300k miles if it's not been
cracked and has had the oil changed regularly.
i'm not endorsing any of the following:
http://www.sunrisejdmmotors.com/
http://www.nippon-motors.com/honda.htm
http://www.naganojapanese.com/
there are a bunch of others if you google.
good luck!
>
> thanks again (exciting saturday, right?).
you're not going anywhere with that motor!
>
> jim beam wrote:
>> larson.joshua@gmail.com wrote:
>>> i've done some looking online and it's difficult to discern what's what
>>> and if a given website is legitimate. that's the biggest difficulty.
>> the biggest thing is to buy with a credit card [not debit card]. that
>> way, ultimately, if there's a problem, the vendor has to work with you
>> and the credit card company to resolve any problems. i'd just go for
>> one of the direct jdm importers with as low a mileage as possible. you
>> don't need much of a warranty - say a month. if it works, has no head
>> problems and doesn't burn oil, you're set - all those will be detectable
>> in the first week or so.
>>
>>> jim - you've helped me in the past and i appreciate that. here's the
>>> long story short: bought the car from a friend. when i bought it, it
>>> probably had a blown head gasket. after a while, the engine blew,
>>> overheated severely and i had head reworked. i did the work and
>>> installed new timing belt, new water pump, and of course new head
>>> gasket.
>>>
>>> the engine seemed to run just okay. it felt tired. then the temp
>>> started fluctuating. replaced thermostat a few times, rad cap a few
>>> times... was losing coolant. figured i messed up first gasket job.
>>> started #2. replaced timing belt, head gasket had head reworked.
>>> replaced distributor after the last one had bad crank sensor (caught
>>> warranty by a week!).
>>>
>>> car runs okay, but here's the thing it did after 1st and 2nd head
>>> gasket job: after i drive for a while, some kind of gas gets into the
>>> cooling system. it bubbles, not boils, pretty vigorously after i come
>>> home (up a mountainside). i could live with this, but i have to check
>>> the fluid levels every couple days now. the gas pushes coolant out,
>>> overflows the resevoir, makes a mess and then i have to fill it back
>>> up.
>> something's cracked.
>>
>>> i am now feeling like the block is cracked or something else is majorly
>>> messed up. plus, i'm a little sick of working on this engine...
>> replacement is 100% the way to go - not worth wasting another single
>> moment on that motor. onwards!
>>
>>>
>>> jim beam wrote:
>>>> larson.joshua@gmail.com wrote:
>>>>> i'm considering replacing the engine in my 1991 civic DX - i think it
>>>>> is a D15B2.
>>>>>
>>>>> i think i want just a straight replacement. i'm more interested in
>>>>> fuel economy than performance.
>>>>>
>>>>> does anyone have any experience or advice regarding purchasing engines?
>>>>> i need practical information regarding JDM engines, buying online and
>>>>> warranties.
>>>>>
>>>>> thanks!
>>>>>
>>>> what's wrong with yours and why do you want to replace it? how many
>>>> miles? i ask because if you think it's not performing right, there are
>>>> a number of possible causes, all of which are cheaper and less
>>>> troublesome than replacing the whole unit.
>
> thanks jim,
>
> i appreciate your help! do you know of any reputable vendors of these
> jdm motors? you mentioned "one of the direct jdm importers."
>
> also, is this industry legit? as in, are the mileages they quote for
> real or is it just B.S.? would i be better off going to the junk yard?
no, it's legit. mileages should be about right - other markets,
particularly japan, do much lower mileage than us. that's why i'd only
buy a domestic motor in emergency - /much/ higher mileage. but that
said, there's no reason a d15 can't do 300k miles if it's not been
cracked and has had the oil changed regularly.
i'm not endorsing any of the following:
http://www.sunrisejdmmotors.com/
http://www.nippon-motors.com/honda.htm
http://www.naganojapanese.com/
there are a bunch of others if you google.
good luck!
>
> thanks again (exciting saturday, right?).
you're not going anywhere with that motor!
>
> jim beam wrote:
>> larson.joshua@gmail.com wrote:
>>> i've done some looking online and it's difficult to discern what's what
>>> and if a given website is legitimate. that's the biggest difficulty.
>> the biggest thing is to buy with a credit card [not debit card]. that
>> way, ultimately, if there's a problem, the vendor has to work with you
>> and the credit card company to resolve any problems. i'd just go for
>> one of the direct jdm importers with as low a mileage as possible. you
>> don't need much of a warranty - say a month. if it works, has no head
>> problems and doesn't burn oil, you're set - all those will be detectable
>> in the first week or so.
>>
>>> jim - you've helped me in the past and i appreciate that. here's the
>>> long story short: bought the car from a friend. when i bought it, it
>>> probably had a blown head gasket. after a while, the engine blew,
>>> overheated severely and i had head reworked. i did the work and
>>> installed new timing belt, new water pump, and of course new head
>>> gasket.
>>>
>>> the engine seemed to run just okay. it felt tired. then the temp
>>> started fluctuating. replaced thermostat a few times, rad cap a few
>>> times... was losing coolant. figured i messed up first gasket job.
>>> started #2. replaced timing belt, head gasket had head reworked.
>>> replaced distributor after the last one had bad crank sensor (caught
>>> warranty by a week!).
>>>
>>> car runs okay, but here's the thing it did after 1st and 2nd head
>>> gasket job: after i drive for a while, some kind of gas gets into the
>>> cooling system. it bubbles, not boils, pretty vigorously after i come
>>> home (up a mountainside). i could live with this, but i have to check
>>> the fluid levels every couple days now. the gas pushes coolant out,
>>> overflows the resevoir, makes a mess and then i have to fill it back
>>> up.
>> something's cracked.
>>
>>> i am now feeling like the block is cracked or something else is majorly
>>> messed up. plus, i'm a little sick of working on this engine...
>> replacement is 100% the way to go - not worth wasting another single
>> moment on that motor. onwards!
>>
>>>
>>> jim beam wrote:
>>>> larson.joshua@gmail.com wrote:
>>>>> i'm considering replacing the engine in my 1991 civic DX - i think it
>>>>> is a D15B2.
>>>>>
>>>>> i think i want just a straight replacement. i'm more interested in
>>>>> fuel economy than performance.
>>>>>
>>>>> does anyone have any experience or advice regarding purchasing engines?
>>>>> i need practical information regarding JDM engines, buying online and
>>>>> warranties.
>>>>>
>>>>> thanks!
>>>>>
>>>> what's wrong with yours and why do you want to replace it? how many
>>>> miles? i ask because if you think it's not performing right, there are
>>>> a number of possible causes, all of which are cheaper and less
>>>> troublesome than replacing the whole unit.
>
12-30-2006, 11:49 PM
#23
Guest
Posts: n/a
Re: Buying a replacement engine
larson.joshua@gmail.com wrote:
> thanks jim,
>
> i appreciate your help! do you know of any reputable vendors of these
> jdm motors? you mentioned "one of the direct jdm importers."
>
> also, is this industry legit? as in, are the mileages they quote for
> real or is it just B.S.? would i be better off going to the junk yard?
no, it's legit. mileages should be about right - other markets,
particularly japan, do much lower mileage than us. that's why i'd only
buy a domestic motor in emergency - /much/ higher mileage. but that
said, there's no reason a d15 can't do 300k miles if it's not been
cracked and has had the oil changed regularly.
i'm not endorsing any of the following:
http://www.sunrisejdmmotors.com/
http://www.nippon-motors.com/honda.htm
http://www.naganojapanese.com/
there are a bunch of others if you google.
good luck!
>
> thanks again (exciting saturday, right?).
you're not going anywhere with that motor!
>
> jim beam wrote:
>> larson.joshua@gmail.com wrote:
>>> i've done some looking online and it's difficult to discern what's what
>>> and if a given website is legitimate. that's the biggest difficulty.
>> the biggest thing is to buy with a credit card [not debit card]. that
>> way, ultimately, if there's a problem, the vendor has to work with you
>> and the credit card company to resolve any problems. i'd just go for
>> one of the direct jdm importers with as low a mileage as possible. you
>> don't need much of a warranty - say a month. if it works, has no head
>> problems and doesn't burn oil, you're set - all those will be detectable
>> in the first week or so.
>>
>>> jim - you've helped me in the past and i appreciate that. here's the
>>> long story short: bought the car from a friend. when i bought it, it
>>> probably had a blown head gasket. after a while, the engine blew,
>>> overheated severely and i had head reworked. i did the work and
>>> installed new timing belt, new water pump, and of course new head
>>> gasket.
>>>
>>> the engine seemed to run just okay. it felt tired. then the temp
>>> started fluctuating. replaced thermostat a few times, rad cap a few
>>> times... was losing coolant. figured i messed up first gasket job.
>>> started #2. replaced timing belt, head gasket had head reworked.
>>> replaced distributor after the last one had bad crank sensor (caught
>>> warranty by a week!).
>>>
>>> car runs okay, but here's the thing it did after 1st and 2nd head
>>> gasket job: after i drive for a while, some kind of gas gets into the
>>> cooling system. it bubbles, not boils, pretty vigorously after i come
>>> home (up a mountainside). i could live with this, but i have to check
>>> the fluid levels every couple days now. the gas pushes coolant out,
>>> overflows the resevoir, makes a mess and then i have to fill it back
>>> up.
>> something's cracked.
>>
>>> i am now feeling like the block is cracked or something else is majorly
>>> messed up. plus, i'm a little sick of working on this engine...
>> replacement is 100% the way to go - not worth wasting another single
>> moment on that motor. onwards!
>>
>>>
>>> jim beam wrote:
>>>> larson.joshua@gmail.com wrote:
>>>>> i'm considering replacing the engine in my 1991 civic DX - i think it
>>>>> is a D15B2.
>>>>>
>>>>> i think i want just a straight replacement. i'm more interested in
>>>>> fuel economy than performance.
>>>>>
>>>>> does anyone have any experience or advice regarding purchasing engines?
>>>>> i need practical information regarding JDM engines, buying online and
>>>>> warranties.
>>>>>
>>>>> thanks!
>>>>>
>>>> what's wrong with yours and why do you want to replace it? how many
>>>> miles? i ask because if you think it's not performing right, there are
>>>> a number of possible causes, all of which are cheaper and less
>>>> troublesome than replacing the whole unit.
>
> thanks jim,
>
> i appreciate your help! do you know of any reputable vendors of these
> jdm motors? you mentioned "one of the direct jdm importers."
>
> also, is this industry legit? as in, are the mileages they quote for
> real or is it just B.S.? would i be better off going to the junk yard?
no, it's legit. mileages should be about right - other markets,
particularly japan, do much lower mileage than us. that's why i'd only
buy a domestic motor in emergency - /much/ higher mileage. but that
said, there's no reason a d15 can't do 300k miles if it's not been
cracked and has had the oil changed regularly.
i'm not endorsing any of the following:
http://www.sunrisejdmmotors.com/
http://www.nippon-motors.com/honda.htm
http://www.naganojapanese.com/
there are a bunch of others if you google.
good luck!
>
> thanks again (exciting saturday, right?).
you're not going anywhere with that motor!
>
> jim beam wrote:
>> larson.joshua@gmail.com wrote:
>>> i've done some looking online and it's difficult to discern what's what
>>> and if a given website is legitimate. that's the biggest difficulty.
>> the biggest thing is to buy with a credit card [not debit card]. that
>> way, ultimately, if there's a problem, the vendor has to work with you
>> and the credit card company to resolve any problems. i'd just go for
>> one of the direct jdm importers with as low a mileage as possible. you
>> don't need much of a warranty - say a month. if it works, has no head
>> problems and doesn't burn oil, you're set - all those will be detectable
>> in the first week or so.
>>
>>> jim - you've helped me in the past and i appreciate that. here's the
>>> long story short: bought the car from a friend. when i bought it, it
>>> probably had a blown head gasket. after a while, the engine blew,
>>> overheated severely and i had head reworked. i did the work and
>>> installed new timing belt, new water pump, and of course new head
>>> gasket.
>>>
>>> the engine seemed to run just okay. it felt tired. then the temp
>>> started fluctuating. replaced thermostat a few times, rad cap a few
>>> times... was losing coolant. figured i messed up first gasket job.
>>> started #2. replaced timing belt, head gasket had head reworked.
>>> replaced distributor after the last one had bad crank sensor (caught
>>> warranty by a week!).
>>>
>>> car runs okay, but here's the thing it did after 1st and 2nd head
>>> gasket job: after i drive for a while, some kind of gas gets into the
>>> cooling system. it bubbles, not boils, pretty vigorously after i come
>>> home (up a mountainside). i could live with this, but i have to check
>>> the fluid levels every couple days now. the gas pushes coolant out,
>>> overflows the resevoir, makes a mess and then i have to fill it back
>>> up.
>> something's cracked.
>>
>>> i am now feeling like the block is cracked or something else is majorly
>>> messed up. plus, i'm a little sick of working on this engine...
>> replacement is 100% the way to go - not worth wasting another single
>> moment on that motor. onwards!
>>
>>>
>>> jim beam wrote:
>>>> larson.joshua@gmail.com wrote:
>>>>> i'm considering replacing the engine in my 1991 civic DX - i think it
>>>>> is a D15B2.
>>>>>
>>>>> i think i want just a straight replacement. i'm more interested in
>>>>> fuel economy than performance.
>>>>>
>>>>> does anyone have any experience or advice regarding purchasing engines?
>>>>> i need practical information regarding JDM engines, buying online and
>>>>> warranties.
>>>>>
>>>>> thanks!
>>>>>
>>>> what's wrong with yours and why do you want to replace it? how many
>>>> miles? i ask because if you think it's not performing right, there are
>>>> a number of possible causes, all of which are cheaper and less
>>>> troublesome than replacing the whole unit.
>
12-31-2006, 12:10 AM
#24
Guest
Posts: n/a
Re: Buying a replacement engine
jim beam wrote:
>
> the biggest thing is to buy with a credit card [not debit card]. that
> way, ultimately, if there's a problem, the vendor has to work with you
> and the credit card company to resolve any problems. i'd just go for
> one of the direct jdm importers with as low a mileage as possible. you
> don't need much of a warranty - say a month. if it works, has no head
> problems and doesn't burn oil, you're set - all those will be detectable
> in the first week or so.
>
Ah, but how is one to know if the stated mileage is accurate? And what
do you know about how the engine was maintained ... nothing.
Sounds like a crap shoot to me.
>
> the biggest thing is to buy with a credit card [not debit card]. that
> way, ultimately, if there's a problem, the vendor has to work with you
> and the credit card company to resolve any problems. i'd just go for
> one of the direct jdm importers with as low a mileage as possible. you
> don't need much of a warranty - say a month. if it works, has no head
> problems and doesn't burn oil, you're set - all those will be detectable
> in the first week or so.
>
Ah, but how is one to know if the stated mileage is accurate? And what
do you know about how the engine was maintained ... nothing.
Sounds like a crap shoot to me.
12-31-2006, 12:10 AM
#25
Guest
Posts: n/a
Re: Buying a replacement engine
jim beam wrote:
>
> the biggest thing is to buy with a credit card [not debit card]. that
> way, ultimately, if there's a problem, the vendor has to work with you
> and the credit card company to resolve any problems. i'd just go for
> one of the direct jdm importers with as low a mileage as possible. you
> don't need much of a warranty - say a month. if it works, has no head
> problems and doesn't burn oil, you're set - all those will be detectable
> in the first week or so.
>
Ah, but how is one to know if the stated mileage is accurate? And what
do you know about how the engine was maintained ... nothing.
Sounds like a crap shoot to me.
>
> the biggest thing is to buy with a credit card [not debit card]. that
> way, ultimately, if there's a problem, the vendor has to work with you
> and the credit card company to resolve any problems. i'd just go for
> one of the direct jdm importers with as low a mileage as possible. you
> don't need much of a warranty - say a month. if it works, has no head
> problems and doesn't burn oil, you're set - all those will be detectable
> in the first week or so.
>
Ah, but how is one to know if the stated mileage is accurate? And what
do you know about how the engine was maintained ... nothing.
Sounds like a crap shoot to me.
12-31-2006, 12:10 AM
#26
Guest
Posts: n/a
Re: Buying a replacement engine
jim beam wrote:
>
> the biggest thing is to buy with a credit card [not debit card]. that
> way, ultimately, if there's a problem, the vendor has to work with you
> and the credit card company to resolve any problems. i'd just go for
> one of the direct jdm importers with as low a mileage as possible. you
> don't need much of a warranty - say a month. if it works, has no head
> problems and doesn't burn oil, you're set - all those will be detectable
> in the first week or so.
>
Ah, but how is one to know if the stated mileage is accurate? And what
do you know about how the engine was maintained ... nothing.
Sounds like a crap shoot to me.
>
> the biggest thing is to buy with a credit card [not debit card]. that
> way, ultimately, if there's a problem, the vendor has to work with you
> and the credit card company to resolve any problems. i'd just go for
> one of the direct jdm importers with as low a mileage as possible. you
> don't need much of a warranty - say a month. if it works, has no head
> problems and doesn't burn oil, you're set - all those will be detectable
> in the first week or so.
>
Ah, but how is one to know if the stated mileage is accurate? And what
do you know about how the engine was maintained ... nothing.
Sounds like a crap shoot to me.
12-31-2006, 01:36 AM
#27
Guest
Posts: n/a
Re: Buying a replacement engine
John Horner wrote:
> jim beam wrote:
>
>>
>> the biggest thing is to buy with a credit card [not debit card]. that
>> way, ultimately, if there's a problem, the vendor has to work with you
>> and the credit card company to resolve any problems. i'd just go for
>> one of the direct jdm importers with as low a mileage as possible.
>> you don't need much of a warranty - say a month. if it works, has no
>> head problems and doesn't burn oil, you're set - all those will be
>> detectable in the first week or so.
>>
>
> Ah, but how is one to know if the stated mileage is accurate? And what
> do you know about how the engine was maintained ... nothing.
>
> Sounds like a crap shoot to me.
>
you have no way of ensuring mileage accuracy with a domestic junk yard
either. well, you kind of do - you're guaranteed that it's done a /lot/
more miles than a japanese motor.
one more thing worth consideration. in the hondas i've had, the
japanese made motors seem to be better balanced than the ones made here.
there's no real reason why this should be, but that's been my experience.
> jim beam wrote:
>
>>
>> the biggest thing is to buy with a credit card [not debit card]. that
>> way, ultimately, if there's a problem, the vendor has to work with you
>> and the credit card company to resolve any problems. i'd just go for
>> one of the direct jdm importers with as low a mileage as possible.
>> you don't need much of a warranty - say a month. if it works, has no
>> head problems and doesn't burn oil, you're set - all those will be
>> detectable in the first week or so.
>>
>
> Ah, but how is one to know if the stated mileage is accurate? And what
> do you know about how the engine was maintained ... nothing.
>
> Sounds like a crap shoot to me.
>
you have no way of ensuring mileage accuracy with a domestic junk yard
either. well, you kind of do - you're guaranteed that it's done a /lot/
more miles than a japanese motor.
one more thing worth consideration. in the hondas i've had, the
japanese made motors seem to be better balanced than the ones made here.
there's no real reason why this should be, but that's been my experience.
12-31-2006, 01:36 AM
#28
Guest
Posts: n/a
Re: Buying a replacement engine
John Horner wrote:
> jim beam wrote:
>
>>
>> the biggest thing is to buy with a credit card [not debit card]. that
>> way, ultimately, if there's a problem, the vendor has to work with you
>> and the credit card company to resolve any problems. i'd just go for
>> one of the direct jdm importers with as low a mileage as possible.
>> you don't need much of a warranty - say a month. if it works, has no
>> head problems and doesn't burn oil, you're set - all those will be
>> detectable in the first week or so.
>>
>
> Ah, but how is one to know if the stated mileage is accurate? And what
> do you know about how the engine was maintained ... nothing.
>
> Sounds like a crap shoot to me.
>
you have no way of ensuring mileage accuracy with a domestic junk yard
either. well, you kind of do - you're guaranteed that it's done a /lot/
more miles than a japanese motor.
one more thing worth consideration. in the hondas i've had, the
japanese made motors seem to be better balanced than the ones made here.
there's no real reason why this should be, but that's been my experience.
> jim beam wrote:
>
>>
>> the biggest thing is to buy with a credit card [not debit card]. that
>> way, ultimately, if there's a problem, the vendor has to work with you
>> and the credit card company to resolve any problems. i'd just go for
>> one of the direct jdm importers with as low a mileage as possible.
>> you don't need much of a warranty - say a month. if it works, has no
>> head problems and doesn't burn oil, you're set - all those will be
>> detectable in the first week or so.
>>
>
> Ah, but how is one to know if the stated mileage is accurate? And what
> do you know about how the engine was maintained ... nothing.
>
> Sounds like a crap shoot to me.
>
you have no way of ensuring mileage accuracy with a domestic junk yard
either. well, you kind of do - you're guaranteed that it's done a /lot/
more miles than a japanese motor.
one more thing worth consideration. in the hondas i've had, the
japanese made motors seem to be better balanced than the ones made here.
there's no real reason why this should be, but that's been my experience.
12-31-2006, 01:36 AM
#29
Guest
Posts: n/a
Re: Buying a replacement engine
John Horner wrote:
> jim beam wrote:
>
>>
>> the biggest thing is to buy with a credit card [not debit card]. that
>> way, ultimately, if there's a problem, the vendor has to work with you
>> and the credit card company to resolve any problems. i'd just go for
>> one of the direct jdm importers with as low a mileage as possible.
>> you don't need much of a warranty - say a month. if it works, has no
>> head problems and doesn't burn oil, you're set - all those will be
>> detectable in the first week or so.
>>
>
> Ah, but how is one to know if the stated mileage is accurate? And what
> do you know about how the engine was maintained ... nothing.
>
> Sounds like a crap shoot to me.
>
you have no way of ensuring mileage accuracy with a domestic junk yard
either. well, you kind of do - you're guaranteed that it's done a /lot/
more miles than a japanese motor.
one more thing worth consideration. in the hondas i've had, the
japanese made motors seem to be better balanced than the ones made here.
there's no real reason why this should be, but that's been my experience.
> jim beam wrote:
>
>>
>> the biggest thing is to buy with a credit card [not debit card]. that
>> way, ultimately, if there's a problem, the vendor has to work with you
>> and the credit card company to resolve any problems. i'd just go for
>> one of the direct jdm importers with as low a mileage as possible.
>> you don't need much of a warranty - say a month. if it works, has no
>> head problems and doesn't burn oil, you're set - all those will be
>> detectable in the first week or so.
>>
>
> Ah, but how is one to know if the stated mileage is accurate? And what
> do you know about how the engine was maintained ... nothing.
>
> Sounds like a crap shoot to me.
>
you have no way of ensuring mileage accuracy with a domestic junk yard
either. well, you kind of do - you're guaranteed that it's done a /lot/
more miles than a japanese motor.
one more thing worth consideration. in the hondas i've had, the
japanese made motors seem to be better balanced than the ones made here.
there's no real reason why this should be, but that's been my experience.
12-31-2006, 09:18 AM
#30
Guest
Posts: n/a
Re: Buying a replacement engine
"John Horner" <jthorner@yahoo.com> wrote in message
news:9DHlh.6785$tc5.2649@trnddc01...
> jim beam wrote:
>
>>
>> the biggest thing is to buy with a credit card [not debit card]. that
>> way, ultimately, if there's a problem, the vendor has to work with you
>> and the credit card company to resolve any problems. i'd just go for one
>> of the direct jdm importers with as low a mileage as possible. you don't
>> need much of a warranty - say a month. if it works, has no head problems
>> and doesn't burn oil, you're set - all those will be detectable in the
>> first week or so.
>>
>
> Ah, but how is one to know if the stated mileage is accurate? And what do
> you know about how the engine was maintained ... nothing.
>
> Sounds like a crap shoot to me.
>
There's something about a car that isn't?
The odds should be good, though. As I understand it Japanese emission
standards are so tight that engines are replaced because of normal wear long
before they would be considered unserviceable here.
I would put a new timing belt and water pump on before putting the engine in
a car, though. It's got to be easier to do on a stand, and then the new
owner knows when it is due again.
Mike
news:9DHlh.6785$tc5.2649@trnddc01...
> jim beam wrote:
>
>>
>> the biggest thing is to buy with a credit card [not debit card]. that
>> way, ultimately, if there's a problem, the vendor has to work with you
>> and the credit card company to resolve any problems. i'd just go for one
>> of the direct jdm importers with as low a mileage as possible. you don't
>> need much of a warranty - say a month. if it works, has no head problems
>> and doesn't burn oil, you're set - all those will be detectable in the
>> first week or so.
>>
>
> Ah, but how is one to know if the stated mileage is accurate? And what do
> you know about how the engine was maintained ... nothing.
>
> Sounds like a crap shoot to me.
>
There's something about a car that isn't?
The odds should be good, though. As I understand it Japanese emission
standards are so tight that engines are replaced because of normal wear long
before they would be considered unserviceable here.
I would put a new timing belt and water pump on before putting the engine in
a car, though. It's got to be easier to do on a stand, and then the new
owner knows when it is due again.
Mike