How Hard is DIY Valve Adjustment?
#16
Guest
Posts: n/a
Re: How Hard is DIY Valve Adjustment?
mjc13<REMOVETHIS> wrote:
.. . . .I was hoping
> to turn the engine by rolling the car in gear. Any problem with that
> approach?
-------------------------------------
Yes, you'll run out of room on your driveway before you get your valves
all adjusted :-)
Once you slip out the spark plugs the engine turns over easily with the
Power Steering nut. (depending on the model)
Engine should be STONE COLD too, at least on the GEn 1 CR-V it's true.
'Curly'
.. . . .I was hoping
> to turn the engine by rolling the car in gear. Any problem with that
> approach?
-------------------------------------
Yes, you'll run out of room on your driveway before you get your valves
all adjusted :-)
Once you slip out the spark plugs the engine turns over easily with the
Power Steering nut. (depending on the model)
Engine should be STONE COLD too, at least on the GEn 1 CR-V it's true.
'Curly'
#17
Guest
Posts: n/a
Re: How Hard is DIY Valve Adjustment?
"mjc13" wrote:
>
> Tegger wrote:
> > "mjc13<REMOVETHIS>" <"mjc13<REMOVETHIS>"@verizon.net> wrote in
> > news:7uBgi.5806$bj5.2829@trndny07:
> >
> >
> >>motsco_ wrote:
> >>
> >>>mjc13<REMOVETHIS> wrote:
> >>>
> >>>
> >>>> Once again, this is a 1995 Civic EX 1.6L 125HP sedan. Don't have
> >>>>the serial number at hand. I've done valve lash adjustments on old
> >>>>Volvo pushrod engines, but nothing like this. It sounds like the
> >>>>adjustment mechanism is surprisingly similar, though: set screw and
> >>>>locknut. So, any tricks? Is this something best left to a seasoned
> >>>>mechanic? I have the Chilton manual.
> >>>
> >>>
> >>>---------------------------------------
> >>>
> >>>For better control / leverage, it's nice if you have a long-handle
> >>>combination wrench, like the 'pro' series one I picked up. It's even
> >>>nicer if you have the tool that holds the locknut and has a
> >>>screwdriver built it. GOOGLE 'powerbuilt 648828' or similar,
> >>>depending on the size of the '95's locknut. I have one but haven't
> >>>used it yet.
> >>>
> >>>'Curly'
> >>
> >>
> >> I was going to use a torque wrench. That isn't critical?
> >>
> >
> >
> >
> >
> > It *most certainly* is.
> >
> > I do my valves every year. I use no special tools, just a flat-blade
> > screwdriver, a 12mm wrench and a feeler gauge set.
> >
> > The critical thing to do is to make certain the cam lobes you check are
> > pointing stright up to the sky. This ensures their ramps are nowhere
> > near the rocker mechanism, so cannot affect readings.
> >
> > Turn engine COUNTER-clockwise with your ratchet. If you have need to go
> > the other way, do that only for fine-tuning of cam position. Never turn
> > clockwise more than a degree or two.
> >
>
> I assume you mean a torque wrench with 12mm socket. ;-) I was hoping
> to turn the engine by rolling the car in gear. Any problem with that
> approach? I don't remember if the manual gives the bolt size - is 12mm
> applicable to my '95 EX?
There is no need for a torque wrench. In addition, you may want to take a
look at one of my prior posts where I discuss the general technique for
adjusting valves. http://tinyurl.com/2bf5qf
Eric
>
> Tegger wrote:
> > "mjc13<REMOVETHIS>" <"mjc13<REMOVETHIS>"@verizon.net> wrote in
> > news:7uBgi.5806$bj5.2829@trndny07:
> >
> >
> >>motsco_ wrote:
> >>
> >>>mjc13<REMOVETHIS> wrote:
> >>>
> >>>
> >>>> Once again, this is a 1995 Civic EX 1.6L 125HP sedan. Don't have
> >>>>the serial number at hand. I've done valve lash adjustments on old
> >>>>Volvo pushrod engines, but nothing like this. It sounds like the
> >>>>adjustment mechanism is surprisingly similar, though: set screw and
> >>>>locknut. So, any tricks? Is this something best left to a seasoned
> >>>>mechanic? I have the Chilton manual.
> >>>
> >>>
> >>>---------------------------------------
> >>>
> >>>For better control / leverage, it's nice if you have a long-handle
> >>>combination wrench, like the 'pro' series one I picked up. It's even
> >>>nicer if you have the tool that holds the locknut and has a
> >>>screwdriver built it. GOOGLE 'powerbuilt 648828' or similar,
> >>>depending on the size of the '95's locknut. I have one but haven't
> >>>used it yet.
> >>>
> >>>'Curly'
> >>
> >>
> >> I was going to use a torque wrench. That isn't critical?
> >>
> >
> >
> >
> >
> > It *most certainly* is.
> >
> > I do my valves every year. I use no special tools, just a flat-blade
> > screwdriver, a 12mm wrench and a feeler gauge set.
> >
> > The critical thing to do is to make certain the cam lobes you check are
> > pointing stright up to the sky. This ensures their ramps are nowhere
> > near the rocker mechanism, so cannot affect readings.
> >
> > Turn engine COUNTER-clockwise with your ratchet. If you have need to go
> > the other way, do that only for fine-tuning of cam position. Never turn
> > clockwise more than a degree or two.
> >
>
> I assume you mean a torque wrench with 12mm socket. ;-) I was hoping
> to turn the engine by rolling the car in gear. Any problem with that
> approach? I don't remember if the manual gives the bolt size - is 12mm
> applicable to my '95 EX?
There is no need for a torque wrench. In addition, you may want to take a
look at one of my prior posts where I discuss the general technique for
adjusting valves. http://tinyurl.com/2bf5qf
Eric
#18
Guest
Posts: n/a
Re: How Hard is DIY Valve Adjustment?
"mjc13" wrote:
>
> Tegger wrote:
> > "mjc13<REMOVETHIS>" <"mjc13<REMOVETHIS>"@verizon.net> wrote in
> > news:7uBgi.5806$bj5.2829@trndny07:
> >
> >
> >>motsco_ wrote:
> >>
> >>>mjc13<REMOVETHIS> wrote:
> >>>
> >>>
> >>>> Once again, this is a 1995 Civic EX 1.6L 125HP sedan. Don't have
> >>>>the serial number at hand. I've done valve lash adjustments on old
> >>>>Volvo pushrod engines, but nothing like this. It sounds like the
> >>>>adjustment mechanism is surprisingly similar, though: set screw and
> >>>>locknut. So, any tricks? Is this something best left to a seasoned
> >>>>mechanic? I have the Chilton manual.
> >>>
> >>>
> >>>---------------------------------------
> >>>
> >>>For better control / leverage, it's nice if you have a long-handle
> >>>combination wrench, like the 'pro' series one I picked up. It's even
> >>>nicer if you have the tool that holds the locknut and has a
> >>>screwdriver built it. GOOGLE 'powerbuilt 648828' or similar,
> >>>depending on the size of the '95's locknut. I have one but haven't
> >>>used it yet.
> >>>
> >>>'Curly'
> >>
> >>
> >> I was going to use a torque wrench. That isn't critical?
> >>
> >
> >
> >
> >
> > It *most certainly* is.
> >
> > I do my valves every year. I use no special tools, just a flat-blade
> > screwdriver, a 12mm wrench and a feeler gauge set.
> >
> > The critical thing to do is to make certain the cam lobes you check are
> > pointing stright up to the sky. This ensures their ramps are nowhere
> > near the rocker mechanism, so cannot affect readings.
> >
> > Turn engine COUNTER-clockwise with your ratchet. If you have need to go
> > the other way, do that only for fine-tuning of cam position. Never turn
> > clockwise more than a degree or two.
> >
>
> I assume you mean a torque wrench with 12mm socket. ;-) I was hoping
> to turn the engine by rolling the car in gear. Any problem with that
> approach? I don't remember if the manual gives the bolt size - is 12mm
> applicable to my '95 EX?
There is no need for a torque wrench. In addition, you may want to take a
look at one of my prior posts where I discuss the general technique for
adjusting valves. http://tinyurl.com/2bf5qf
Eric
>
> Tegger wrote:
> > "mjc13<REMOVETHIS>" <"mjc13<REMOVETHIS>"@verizon.net> wrote in
> > news:7uBgi.5806$bj5.2829@trndny07:
> >
> >
> >>motsco_ wrote:
> >>
> >>>mjc13<REMOVETHIS> wrote:
> >>>
> >>>
> >>>> Once again, this is a 1995 Civic EX 1.6L 125HP sedan. Don't have
> >>>>the serial number at hand. I've done valve lash adjustments on old
> >>>>Volvo pushrod engines, but nothing like this. It sounds like the
> >>>>adjustment mechanism is surprisingly similar, though: set screw and
> >>>>locknut. So, any tricks? Is this something best left to a seasoned
> >>>>mechanic? I have the Chilton manual.
> >>>
> >>>
> >>>---------------------------------------
> >>>
> >>>For better control / leverage, it's nice if you have a long-handle
> >>>combination wrench, like the 'pro' series one I picked up. It's even
> >>>nicer if you have the tool that holds the locknut and has a
> >>>screwdriver built it. GOOGLE 'powerbuilt 648828' or similar,
> >>>depending on the size of the '95's locknut. I have one but haven't
> >>>used it yet.
> >>>
> >>>'Curly'
> >>
> >>
> >> I was going to use a torque wrench. That isn't critical?
> >>
> >
> >
> >
> >
> > It *most certainly* is.
> >
> > I do my valves every year. I use no special tools, just a flat-blade
> > screwdriver, a 12mm wrench and a feeler gauge set.
> >
> > The critical thing to do is to make certain the cam lobes you check are
> > pointing stright up to the sky. This ensures their ramps are nowhere
> > near the rocker mechanism, so cannot affect readings.
> >
> > Turn engine COUNTER-clockwise with your ratchet. If you have need to go
> > the other way, do that only for fine-tuning of cam position. Never turn
> > clockwise more than a degree or two.
> >
>
> I assume you mean a torque wrench with 12mm socket. ;-) I was hoping
> to turn the engine by rolling the car in gear. Any problem with that
> approach? I don't remember if the manual gives the bolt size - is 12mm
> applicable to my '95 EX?
There is no need for a torque wrench. In addition, you may want to take a
look at one of my prior posts where I discuss the general technique for
adjusting valves. http://tinyurl.com/2bf5qf
Eric
#19
Guest
Posts: n/a
Re: How Hard is DIY Valve Adjustment?
"mjc13" wrote:
>
> Tegger wrote:
> > "mjc13<REMOVETHIS>" <"mjc13<REMOVETHIS>"@verizon.net> wrote in
> > news:7uBgi.5806$bj5.2829@trndny07:
> >
> >
> >>motsco_ wrote:
> >>
> >>>mjc13<REMOVETHIS> wrote:
> >>>
> >>>
> >>>> Once again, this is a 1995 Civic EX 1.6L 125HP sedan. Don't have
> >>>>the serial number at hand. I've done valve lash adjustments on old
> >>>>Volvo pushrod engines, but nothing like this. It sounds like the
> >>>>adjustment mechanism is surprisingly similar, though: set screw and
> >>>>locknut. So, any tricks? Is this something best left to a seasoned
> >>>>mechanic? I have the Chilton manual.
> >>>
> >>>
> >>>---------------------------------------
> >>>
> >>>For better control / leverage, it's nice if you have a long-handle
> >>>combination wrench, like the 'pro' series one I picked up. It's even
> >>>nicer if you have the tool that holds the locknut and has a
> >>>screwdriver built it. GOOGLE 'powerbuilt 648828' or similar,
> >>>depending on the size of the '95's locknut. I have one but haven't
> >>>used it yet.
> >>>
> >>>'Curly'
> >>
> >>
> >> I was going to use a torque wrench. That isn't critical?
> >>
> >
> >
> >
> >
> > It *most certainly* is.
> >
> > I do my valves every year. I use no special tools, just a flat-blade
> > screwdriver, a 12mm wrench and a feeler gauge set.
> >
> > The critical thing to do is to make certain the cam lobes you check are
> > pointing stright up to the sky. This ensures their ramps are nowhere
> > near the rocker mechanism, so cannot affect readings.
> >
> > Turn engine COUNTER-clockwise with your ratchet. If you have need to go
> > the other way, do that only for fine-tuning of cam position. Never turn
> > clockwise more than a degree or two.
> >
>
> I assume you mean a torque wrench with 12mm socket. ;-) I was hoping
> to turn the engine by rolling the car in gear. Any problem with that
> approach? I don't remember if the manual gives the bolt size - is 12mm
> applicable to my '95 EX?
There is no need for a torque wrench. In addition, you may want to take a
look at one of my prior posts where I discuss the general technique for
adjusting valves. http://tinyurl.com/2bf5qf
Eric
>
> Tegger wrote:
> > "mjc13<REMOVETHIS>" <"mjc13<REMOVETHIS>"@verizon.net> wrote in
> > news:7uBgi.5806$bj5.2829@trndny07:
> >
> >
> >>motsco_ wrote:
> >>
> >>>mjc13<REMOVETHIS> wrote:
> >>>
> >>>
> >>>> Once again, this is a 1995 Civic EX 1.6L 125HP sedan. Don't have
> >>>>the serial number at hand. I've done valve lash adjustments on old
> >>>>Volvo pushrod engines, but nothing like this. It sounds like the
> >>>>adjustment mechanism is surprisingly similar, though: set screw and
> >>>>locknut. So, any tricks? Is this something best left to a seasoned
> >>>>mechanic? I have the Chilton manual.
> >>>
> >>>
> >>>---------------------------------------
> >>>
> >>>For better control / leverage, it's nice if you have a long-handle
> >>>combination wrench, like the 'pro' series one I picked up. It's even
> >>>nicer if you have the tool that holds the locknut and has a
> >>>screwdriver built it. GOOGLE 'powerbuilt 648828' or similar,
> >>>depending on the size of the '95's locknut. I have one but haven't
> >>>used it yet.
> >>>
> >>>'Curly'
> >>
> >>
> >> I was going to use a torque wrench. That isn't critical?
> >>
> >
> >
> >
> >
> > It *most certainly* is.
> >
> > I do my valves every year. I use no special tools, just a flat-blade
> > screwdriver, a 12mm wrench and a feeler gauge set.
> >
> > The critical thing to do is to make certain the cam lobes you check are
> > pointing stright up to the sky. This ensures their ramps are nowhere
> > near the rocker mechanism, so cannot affect readings.
> >
> > Turn engine COUNTER-clockwise with your ratchet. If you have need to go
> > the other way, do that only for fine-tuning of cam position. Never turn
> > clockwise more than a degree or two.
> >
>
> I assume you mean a torque wrench with 12mm socket. ;-) I was hoping
> to turn the engine by rolling the car in gear. Any problem with that
> approach? I don't remember if the manual gives the bolt size - is 12mm
> applicable to my '95 EX?
There is no need for a torque wrench. In addition, you may want to take a
look at one of my prior posts where I discuss the general technique for
adjusting valves. http://tinyurl.com/2bf5qf
Eric
#20
Guest
Posts: n/a
Re: How Hard is DIY Valve Adjustment?
Eric wrote:
> "mjc13" wrote:
>
>>Tegger wrote:
>>
>>>"mjc13<REMOVETHIS>" <"mjc13<REMOVETHIS>"@verizon.net> wrote in
>>>news:7uBgi.5806$bj5.2829@trndny07:
>>>
>>>
>>>
>>>>motsco_ wrote:
>>>>
>>>>
>>>>>mjc13<REMOVETHIS> wrote:
>>>>>
>>>>>
>>>>>
>>>>>> Once again, this is a 1995 Civic EX 1.6L 125HP sedan. Don't have
>>>>>>the serial number at hand. I've done valve lash adjustments on old
>>>>>>Volvo pushrod engines, but nothing like this. It sounds like the
>>>>>>adjustment mechanism is surprisingly similar, though: set screw and
>>>>>>locknut. So, any tricks? Is this something best left to a seasoned
>>>>>>mechanic? I have the Chilton manual.
>>>>>
>>>>>
>>>>>---------------------------------------
>>>>>
>>>>>For better control / leverage, it's nice if you have a long-handle
>>>>>combination wrench, like the 'pro' series one I picked up. It's even
>>>>>nicer if you have the tool that holds the locknut and has a
>>>>>screwdriver built it. GOOGLE 'powerbuilt 648828' or similar,
>>>>>depending on the size of the '95's locknut. I have one but haven't
>>>>>used it yet.
>>>>>
>>>>>'Curly'
>>>>
>>>>
>>>> I was going to use a torque wrench. That isn't critical?
>>>>
>>>
>>>
>>>
>>>
>>>It *most certainly* is.
>>>
>>>I do my valves every year. I use no special tools, just a flat-blade
>>>screwdriver, a 12mm wrench and a feeler gauge set.
>>>
>>>The critical thing to do is to make certain the cam lobes you check are
>>>pointing stright up to the sky. This ensures their ramps are nowhere
>>>near the rocker mechanism, so cannot affect readings.
>>>
>>>Turn engine COUNTER-clockwise with your ratchet. If you have need to go
>>>the other way, do that only for fine-tuning of cam position. Never turn
>>>clockwise more than a degree or two.
>>>
>>
>> I assume you mean a torque wrench with 12mm socket. ;-) I was hoping
>>to turn the engine by rolling the car in gear. Any problem with that
>>approach? I don't remember if the manual gives the bolt size - is 12mm
>>applicable to my '95 EX?
>
>
> There is no need for a torque wrench. In addition, you may want to take a
> look at one of my prior posts where I discuss the general technique for
> adjusting valves. http://tinyurl.com/2bf5qf
>
> Eric
There may not be a need for a torque wrench if you either have done
the job before or instinctively know what 14 lb/ft feels like, but I'd
prefer not to risk those aluminum rocker arms.
> "mjc13" wrote:
>
>>Tegger wrote:
>>
>>>"mjc13<REMOVETHIS>" <"mjc13<REMOVETHIS>"@verizon.net> wrote in
>>>news:7uBgi.5806$bj5.2829@trndny07:
>>>
>>>
>>>
>>>>motsco_ wrote:
>>>>
>>>>
>>>>>mjc13<REMOVETHIS> wrote:
>>>>>
>>>>>
>>>>>
>>>>>> Once again, this is a 1995 Civic EX 1.6L 125HP sedan. Don't have
>>>>>>the serial number at hand. I've done valve lash adjustments on old
>>>>>>Volvo pushrod engines, but nothing like this. It sounds like the
>>>>>>adjustment mechanism is surprisingly similar, though: set screw and
>>>>>>locknut. So, any tricks? Is this something best left to a seasoned
>>>>>>mechanic? I have the Chilton manual.
>>>>>
>>>>>
>>>>>---------------------------------------
>>>>>
>>>>>For better control / leverage, it's nice if you have a long-handle
>>>>>combination wrench, like the 'pro' series one I picked up. It's even
>>>>>nicer if you have the tool that holds the locknut and has a
>>>>>screwdriver built it. GOOGLE 'powerbuilt 648828' or similar,
>>>>>depending on the size of the '95's locknut. I have one but haven't
>>>>>used it yet.
>>>>>
>>>>>'Curly'
>>>>
>>>>
>>>> I was going to use a torque wrench. That isn't critical?
>>>>
>>>
>>>
>>>
>>>
>>>It *most certainly* is.
>>>
>>>I do my valves every year. I use no special tools, just a flat-blade
>>>screwdriver, a 12mm wrench and a feeler gauge set.
>>>
>>>The critical thing to do is to make certain the cam lobes you check are
>>>pointing stright up to the sky. This ensures their ramps are nowhere
>>>near the rocker mechanism, so cannot affect readings.
>>>
>>>Turn engine COUNTER-clockwise with your ratchet. If you have need to go
>>>the other way, do that only for fine-tuning of cam position. Never turn
>>>clockwise more than a degree or two.
>>>
>>
>> I assume you mean a torque wrench with 12mm socket. ;-) I was hoping
>>to turn the engine by rolling the car in gear. Any problem with that
>>approach? I don't remember if the manual gives the bolt size - is 12mm
>>applicable to my '95 EX?
>
>
> There is no need for a torque wrench. In addition, you may want to take a
> look at one of my prior posts where I discuss the general technique for
> adjusting valves. http://tinyurl.com/2bf5qf
>
> Eric
There may not be a need for a torque wrench if you either have done
the job before or instinctively know what 14 lb/ft feels like, but I'd
prefer not to risk those aluminum rocker arms.
#21
Guest
Posts: n/a
Re: How Hard is DIY Valve Adjustment?
Eric wrote:
> "mjc13" wrote:
>
>>Tegger wrote:
>>
>>>"mjc13<REMOVETHIS>" <"mjc13<REMOVETHIS>"@verizon.net> wrote in
>>>news:7uBgi.5806$bj5.2829@trndny07:
>>>
>>>
>>>
>>>>motsco_ wrote:
>>>>
>>>>
>>>>>mjc13<REMOVETHIS> wrote:
>>>>>
>>>>>
>>>>>
>>>>>> Once again, this is a 1995 Civic EX 1.6L 125HP sedan. Don't have
>>>>>>the serial number at hand. I've done valve lash adjustments on old
>>>>>>Volvo pushrod engines, but nothing like this. It sounds like the
>>>>>>adjustment mechanism is surprisingly similar, though: set screw and
>>>>>>locknut. So, any tricks? Is this something best left to a seasoned
>>>>>>mechanic? I have the Chilton manual.
>>>>>
>>>>>
>>>>>---------------------------------------
>>>>>
>>>>>For better control / leverage, it's nice if you have a long-handle
>>>>>combination wrench, like the 'pro' series one I picked up. It's even
>>>>>nicer if you have the tool that holds the locknut and has a
>>>>>screwdriver built it. GOOGLE 'powerbuilt 648828' or similar,
>>>>>depending on the size of the '95's locknut. I have one but haven't
>>>>>used it yet.
>>>>>
>>>>>'Curly'
>>>>
>>>>
>>>> I was going to use a torque wrench. That isn't critical?
>>>>
>>>
>>>
>>>
>>>
>>>It *most certainly* is.
>>>
>>>I do my valves every year. I use no special tools, just a flat-blade
>>>screwdriver, a 12mm wrench and a feeler gauge set.
>>>
>>>The critical thing to do is to make certain the cam lobes you check are
>>>pointing stright up to the sky. This ensures their ramps are nowhere
>>>near the rocker mechanism, so cannot affect readings.
>>>
>>>Turn engine COUNTER-clockwise with your ratchet. If you have need to go
>>>the other way, do that only for fine-tuning of cam position. Never turn
>>>clockwise more than a degree or two.
>>>
>>
>> I assume you mean a torque wrench with 12mm socket. ;-) I was hoping
>>to turn the engine by rolling the car in gear. Any problem with that
>>approach? I don't remember if the manual gives the bolt size - is 12mm
>>applicable to my '95 EX?
>
>
> There is no need for a torque wrench. In addition, you may want to take a
> look at one of my prior posts where I discuss the general technique for
> adjusting valves. http://tinyurl.com/2bf5qf
>
> Eric
There may not be a need for a torque wrench if you either have done
the job before or instinctively know what 14 lb/ft feels like, but I'd
prefer not to risk those aluminum rocker arms.
> "mjc13" wrote:
>
>>Tegger wrote:
>>
>>>"mjc13<REMOVETHIS>" <"mjc13<REMOVETHIS>"@verizon.net> wrote in
>>>news:7uBgi.5806$bj5.2829@trndny07:
>>>
>>>
>>>
>>>>motsco_ wrote:
>>>>
>>>>
>>>>>mjc13<REMOVETHIS> wrote:
>>>>>
>>>>>
>>>>>
>>>>>> Once again, this is a 1995 Civic EX 1.6L 125HP sedan. Don't have
>>>>>>the serial number at hand. I've done valve lash adjustments on old
>>>>>>Volvo pushrod engines, but nothing like this. It sounds like the
>>>>>>adjustment mechanism is surprisingly similar, though: set screw and
>>>>>>locknut. So, any tricks? Is this something best left to a seasoned
>>>>>>mechanic? I have the Chilton manual.
>>>>>
>>>>>
>>>>>---------------------------------------
>>>>>
>>>>>For better control / leverage, it's nice if you have a long-handle
>>>>>combination wrench, like the 'pro' series one I picked up. It's even
>>>>>nicer if you have the tool that holds the locknut and has a
>>>>>screwdriver built it. GOOGLE 'powerbuilt 648828' or similar,
>>>>>depending on the size of the '95's locknut. I have one but haven't
>>>>>used it yet.
>>>>>
>>>>>'Curly'
>>>>
>>>>
>>>> I was going to use a torque wrench. That isn't critical?
>>>>
>>>
>>>
>>>
>>>
>>>It *most certainly* is.
>>>
>>>I do my valves every year. I use no special tools, just a flat-blade
>>>screwdriver, a 12mm wrench and a feeler gauge set.
>>>
>>>The critical thing to do is to make certain the cam lobes you check are
>>>pointing stright up to the sky. This ensures their ramps are nowhere
>>>near the rocker mechanism, so cannot affect readings.
>>>
>>>Turn engine COUNTER-clockwise with your ratchet. If you have need to go
>>>the other way, do that only for fine-tuning of cam position. Never turn
>>>clockwise more than a degree or two.
>>>
>>
>> I assume you mean a torque wrench with 12mm socket. ;-) I was hoping
>>to turn the engine by rolling the car in gear. Any problem with that
>>approach? I don't remember if the manual gives the bolt size - is 12mm
>>applicable to my '95 EX?
>
>
> There is no need for a torque wrench. In addition, you may want to take a
> look at one of my prior posts where I discuss the general technique for
> adjusting valves. http://tinyurl.com/2bf5qf
>
> Eric
There may not be a need for a torque wrench if you either have done
the job before or instinctively know what 14 lb/ft feels like, but I'd
prefer not to risk those aluminum rocker arms.
#22
Guest
Posts: n/a
Re: How Hard is DIY Valve Adjustment?
Eric wrote:
> "mjc13" wrote:
>
>>Tegger wrote:
>>
>>>"mjc13<REMOVETHIS>" <"mjc13<REMOVETHIS>"@verizon.net> wrote in
>>>news:7uBgi.5806$bj5.2829@trndny07:
>>>
>>>
>>>
>>>>motsco_ wrote:
>>>>
>>>>
>>>>>mjc13<REMOVETHIS> wrote:
>>>>>
>>>>>
>>>>>
>>>>>> Once again, this is a 1995 Civic EX 1.6L 125HP sedan. Don't have
>>>>>>the serial number at hand. I've done valve lash adjustments on old
>>>>>>Volvo pushrod engines, but nothing like this. It sounds like the
>>>>>>adjustment mechanism is surprisingly similar, though: set screw and
>>>>>>locknut. So, any tricks? Is this something best left to a seasoned
>>>>>>mechanic? I have the Chilton manual.
>>>>>
>>>>>
>>>>>---------------------------------------
>>>>>
>>>>>For better control / leverage, it's nice if you have a long-handle
>>>>>combination wrench, like the 'pro' series one I picked up. It's even
>>>>>nicer if you have the tool that holds the locknut and has a
>>>>>screwdriver built it. GOOGLE 'powerbuilt 648828' or similar,
>>>>>depending on the size of the '95's locknut. I have one but haven't
>>>>>used it yet.
>>>>>
>>>>>'Curly'
>>>>
>>>>
>>>> I was going to use a torque wrench. That isn't critical?
>>>>
>>>
>>>
>>>
>>>
>>>It *most certainly* is.
>>>
>>>I do my valves every year. I use no special tools, just a flat-blade
>>>screwdriver, a 12mm wrench and a feeler gauge set.
>>>
>>>The critical thing to do is to make certain the cam lobes you check are
>>>pointing stright up to the sky. This ensures their ramps are nowhere
>>>near the rocker mechanism, so cannot affect readings.
>>>
>>>Turn engine COUNTER-clockwise with your ratchet. If you have need to go
>>>the other way, do that only for fine-tuning of cam position. Never turn
>>>clockwise more than a degree or two.
>>>
>>
>> I assume you mean a torque wrench with 12mm socket. ;-) I was hoping
>>to turn the engine by rolling the car in gear. Any problem with that
>>approach? I don't remember if the manual gives the bolt size - is 12mm
>>applicable to my '95 EX?
>
>
> There is no need for a torque wrench. In addition, you may want to take a
> look at one of my prior posts where I discuss the general technique for
> adjusting valves. http://tinyurl.com/2bf5qf
>
> Eric
There may not be a need for a torque wrench if you either have done
the job before or instinctively know what 14 lb/ft feels like, but I'd
prefer not to risk those aluminum rocker arms.
> "mjc13" wrote:
>
>>Tegger wrote:
>>
>>>"mjc13<REMOVETHIS>" <"mjc13<REMOVETHIS>"@verizon.net> wrote in
>>>news:7uBgi.5806$bj5.2829@trndny07:
>>>
>>>
>>>
>>>>motsco_ wrote:
>>>>
>>>>
>>>>>mjc13<REMOVETHIS> wrote:
>>>>>
>>>>>
>>>>>
>>>>>> Once again, this is a 1995 Civic EX 1.6L 125HP sedan. Don't have
>>>>>>the serial number at hand. I've done valve lash adjustments on old
>>>>>>Volvo pushrod engines, but nothing like this. It sounds like the
>>>>>>adjustment mechanism is surprisingly similar, though: set screw and
>>>>>>locknut. So, any tricks? Is this something best left to a seasoned
>>>>>>mechanic? I have the Chilton manual.
>>>>>
>>>>>
>>>>>---------------------------------------
>>>>>
>>>>>For better control / leverage, it's nice if you have a long-handle
>>>>>combination wrench, like the 'pro' series one I picked up. It's even
>>>>>nicer if you have the tool that holds the locknut and has a
>>>>>screwdriver built it. GOOGLE 'powerbuilt 648828' or similar,
>>>>>depending on the size of the '95's locknut. I have one but haven't
>>>>>used it yet.
>>>>>
>>>>>'Curly'
>>>>
>>>>
>>>> I was going to use a torque wrench. That isn't critical?
>>>>
>>>
>>>
>>>
>>>
>>>It *most certainly* is.
>>>
>>>I do my valves every year. I use no special tools, just a flat-blade
>>>screwdriver, a 12mm wrench and a feeler gauge set.
>>>
>>>The critical thing to do is to make certain the cam lobes you check are
>>>pointing stright up to the sky. This ensures their ramps are nowhere
>>>near the rocker mechanism, so cannot affect readings.
>>>
>>>Turn engine COUNTER-clockwise with your ratchet. If you have need to go
>>>the other way, do that only for fine-tuning of cam position. Never turn
>>>clockwise more than a degree or two.
>>>
>>
>> I assume you mean a torque wrench with 12mm socket. ;-) I was hoping
>>to turn the engine by rolling the car in gear. Any problem with that
>>approach? I don't remember if the manual gives the bolt size - is 12mm
>>applicable to my '95 EX?
>
>
> There is no need for a torque wrench. In addition, you may want to take a
> look at one of my prior posts where I discuss the general technique for
> adjusting valves. http://tinyurl.com/2bf5qf
>
> Eric
There may not be a need for a torque wrench if you either have done
the job before or instinctively know what 14 lb/ft feels like, but I'd
prefer not to risk those aluminum rocker arms.
#23
Guest
Posts: n/a
Re: How Hard is DIY Valve Adjustment?
mjc13<REMOVETHIS> wrote:
> Eric wrote:
>> "mjc13" wrote:
>>
>>> Tegger wrote:
>>>
>>>> "mjc13<REMOVETHIS>" <"mjc13<REMOVETHIS>"@verizon.net> wrote in
>>>> news:7uBgi.5806$bj5.2829@trndny07:
>>>>
>>>>
>>>>
>>>>> motsco_ wrote:
>>>>>
>>>>>
>>>>>> mjc13<REMOVETHIS> wrote:
>>>>>>
>>>>>>
>>>>>>
>>>>>>> Once again, this is a 1995 Civic EX 1.6L 125HP sedan. Don't have
>>>>>>> the serial number at hand. I've done valve lash adjustments on old
>>>>>>> Volvo pushrod engines, but nothing like this. It sounds like the
>>>>>>> adjustment mechanism is surprisingly similar, though: set screw and
>>>>>>> locknut. So, any tricks? Is this something best left to a seasoned
>>>>>>> mechanic? I have the Chilton manual.
>>>>>>
>>>>>>
>>>>>> ---------------------------------------
>>>>>>
>>>>>> For better control / leverage, it's nice if you have a long-handle
>>>>>> combination wrench, like the 'pro' series one I picked up. It's even
>>>>>> nicer if you have the tool that holds the locknut and has a
>>>>>> screwdriver built it. GOOGLE 'powerbuilt 648828' or similar,
>>>>>> depending on the size of the '95's locknut. I have one but haven't
>>>>>> used it yet.
>>>>>>
>>>>>> 'Curly'
>>>>>
>>>>>
>>>>> I was going to use a torque wrench. That isn't critical?
>>>>>
>>>>
>>>>
>>>>
>>>>
>>>> It *most certainly* is.
>>>>
>>>> I do my valves every year. I use no special tools, just a flat-blade
>>>> screwdriver, a 12mm wrench and a feeler gauge set.
>>>>
>>>> The critical thing to do is to make certain the cam lobes you check are
>>>> pointing stright up to the sky. This ensures their ramps are nowhere
>>>> near the rocker mechanism, so cannot affect readings.
>>>>
>>>> Turn engine COUNTER-clockwise with your ratchet. If you have need to go
>>>> the other way, do that only for fine-tuning of cam position. Never turn
>>>> clockwise more than a degree or two.
>>>>
>>>
>>> I assume you mean a torque wrench with 12mm socket. ;-) I was hoping
>>> to turn the engine by rolling the car in gear. Any problem with that
>>> approach? I don't remember if the manual gives the bolt size - is 12mm
>>> applicable to my '95 EX?
>>
>>
>> There is no need for a torque wrench. In addition, you may want to
>> take a
>> look at one of my prior posts where I discuss the general technique for
>> adjusting valves. http://tinyurl.com/2bf5qf
>>
>> Eric
>
>
> There may not be a need for a torque wrench if you either have done
> the job before or instinctively know what 14 lb/ft feels like, but I'd
> prefer not to risk those aluminum rocker arms.
i don't think you should attempt this job at this time. it requires
experience and some degree of mechanical aptitude. judging by your
other posts and your reaction to responses, you don't appear to have
either. in fact, your motivation appears to be more recreational than
anything else.
if you're serious about learning, sign up for evening classes. otherwise
leave alone. a fouled up valve adjustment can cost you a lot of money.
> Eric wrote:
>> "mjc13" wrote:
>>
>>> Tegger wrote:
>>>
>>>> "mjc13<REMOVETHIS>" <"mjc13<REMOVETHIS>"@verizon.net> wrote in
>>>> news:7uBgi.5806$bj5.2829@trndny07:
>>>>
>>>>
>>>>
>>>>> motsco_ wrote:
>>>>>
>>>>>
>>>>>> mjc13<REMOVETHIS> wrote:
>>>>>>
>>>>>>
>>>>>>
>>>>>>> Once again, this is a 1995 Civic EX 1.6L 125HP sedan. Don't have
>>>>>>> the serial number at hand. I've done valve lash adjustments on old
>>>>>>> Volvo pushrod engines, but nothing like this. It sounds like the
>>>>>>> adjustment mechanism is surprisingly similar, though: set screw and
>>>>>>> locknut. So, any tricks? Is this something best left to a seasoned
>>>>>>> mechanic? I have the Chilton manual.
>>>>>>
>>>>>>
>>>>>> ---------------------------------------
>>>>>>
>>>>>> For better control / leverage, it's nice if you have a long-handle
>>>>>> combination wrench, like the 'pro' series one I picked up. It's even
>>>>>> nicer if you have the tool that holds the locknut and has a
>>>>>> screwdriver built it. GOOGLE 'powerbuilt 648828' or similar,
>>>>>> depending on the size of the '95's locknut. I have one but haven't
>>>>>> used it yet.
>>>>>>
>>>>>> 'Curly'
>>>>>
>>>>>
>>>>> I was going to use a torque wrench. That isn't critical?
>>>>>
>>>>
>>>>
>>>>
>>>>
>>>> It *most certainly* is.
>>>>
>>>> I do my valves every year. I use no special tools, just a flat-blade
>>>> screwdriver, a 12mm wrench and a feeler gauge set.
>>>>
>>>> The critical thing to do is to make certain the cam lobes you check are
>>>> pointing stright up to the sky. This ensures their ramps are nowhere
>>>> near the rocker mechanism, so cannot affect readings.
>>>>
>>>> Turn engine COUNTER-clockwise with your ratchet. If you have need to go
>>>> the other way, do that only for fine-tuning of cam position. Never turn
>>>> clockwise more than a degree or two.
>>>>
>>>
>>> I assume you mean a torque wrench with 12mm socket. ;-) I was hoping
>>> to turn the engine by rolling the car in gear. Any problem with that
>>> approach? I don't remember if the manual gives the bolt size - is 12mm
>>> applicable to my '95 EX?
>>
>>
>> There is no need for a torque wrench. In addition, you may want to
>> take a
>> look at one of my prior posts where I discuss the general technique for
>> adjusting valves. http://tinyurl.com/2bf5qf
>>
>> Eric
>
>
> There may not be a need for a torque wrench if you either have done
> the job before or instinctively know what 14 lb/ft feels like, but I'd
> prefer not to risk those aluminum rocker arms.
i don't think you should attempt this job at this time. it requires
experience and some degree of mechanical aptitude. judging by your
other posts and your reaction to responses, you don't appear to have
either. in fact, your motivation appears to be more recreational than
anything else.
if you're serious about learning, sign up for evening classes. otherwise
leave alone. a fouled up valve adjustment can cost you a lot of money.
#24
Guest
Posts: n/a
Re: How Hard is DIY Valve Adjustment?
mjc13<REMOVETHIS> wrote:
> Eric wrote:
>> "mjc13" wrote:
>>
>>> Tegger wrote:
>>>
>>>> "mjc13<REMOVETHIS>" <"mjc13<REMOVETHIS>"@verizon.net> wrote in
>>>> news:7uBgi.5806$bj5.2829@trndny07:
>>>>
>>>>
>>>>
>>>>> motsco_ wrote:
>>>>>
>>>>>
>>>>>> mjc13<REMOVETHIS> wrote:
>>>>>>
>>>>>>
>>>>>>
>>>>>>> Once again, this is a 1995 Civic EX 1.6L 125HP sedan. Don't have
>>>>>>> the serial number at hand. I've done valve lash adjustments on old
>>>>>>> Volvo pushrod engines, but nothing like this. It sounds like the
>>>>>>> adjustment mechanism is surprisingly similar, though: set screw and
>>>>>>> locknut. So, any tricks? Is this something best left to a seasoned
>>>>>>> mechanic? I have the Chilton manual.
>>>>>>
>>>>>>
>>>>>> ---------------------------------------
>>>>>>
>>>>>> For better control / leverage, it's nice if you have a long-handle
>>>>>> combination wrench, like the 'pro' series one I picked up. It's even
>>>>>> nicer if you have the tool that holds the locknut and has a
>>>>>> screwdriver built it. GOOGLE 'powerbuilt 648828' or similar,
>>>>>> depending on the size of the '95's locknut. I have one but haven't
>>>>>> used it yet.
>>>>>>
>>>>>> 'Curly'
>>>>>
>>>>>
>>>>> I was going to use a torque wrench. That isn't critical?
>>>>>
>>>>
>>>>
>>>>
>>>>
>>>> It *most certainly* is.
>>>>
>>>> I do my valves every year. I use no special tools, just a flat-blade
>>>> screwdriver, a 12mm wrench and a feeler gauge set.
>>>>
>>>> The critical thing to do is to make certain the cam lobes you check are
>>>> pointing stright up to the sky. This ensures their ramps are nowhere
>>>> near the rocker mechanism, so cannot affect readings.
>>>>
>>>> Turn engine COUNTER-clockwise with your ratchet. If you have need to go
>>>> the other way, do that only for fine-tuning of cam position. Never turn
>>>> clockwise more than a degree or two.
>>>>
>>>
>>> I assume you mean a torque wrench with 12mm socket. ;-) I was hoping
>>> to turn the engine by rolling the car in gear. Any problem with that
>>> approach? I don't remember if the manual gives the bolt size - is 12mm
>>> applicable to my '95 EX?
>>
>>
>> There is no need for a torque wrench. In addition, you may want to
>> take a
>> look at one of my prior posts where I discuss the general technique for
>> adjusting valves. http://tinyurl.com/2bf5qf
>>
>> Eric
>
>
> There may not be a need for a torque wrench if you either have done
> the job before or instinctively know what 14 lb/ft feels like, but I'd
> prefer not to risk those aluminum rocker arms.
i don't think you should attempt this job at this time. it requires
experience and some degree of mechanical aptitude. judging by your
other posts and your reaction to responses, you don't appear to have
either. in fact, your motivation appears to be more recreational than
anything else.
if you're serious about learning, sign up for evening classes. otherwise
leave alone. a fouled up valve adjustment can cost you a lot of money.
> Eric wrote:
>> "mjc13" wrote:
>>
>>> Tegger wrote:
>>>
>>>> "mjc13<REMOVETHIS>" <"mjc13<REMOVETHIS>"@verizon.net> wrote in
>>>> news:7uBgi.5806$bj5.2829@trndny07:
>>>>
>>>>
>>>>
>>>>> motsco_ wrote:
>>>>>
>>>>>
>>>>>> mjc13<REMOVETHIS> wrote:
>>>>>>
>>>>>>
>>>>>>
>>>>>>> Once again, this is a 1995 Civic EX 1.6L 125HP sedan. Don't have
>>>>>>> the serial number at hand. I've done valve lash adjustments on old
>>>>>>> Volvo pushrod engines, but nothing like this. It sounds like the
>>>>>>> adjustment mechanism is surprisingly similar, though: set screw and
>>>>>>> locknut. So, any tricks? Is this something best left to a seasoned
>>>>>>> mechanic? I have the Chilton manual.
>>>>>>
>>>>>>
>>>>>> ---------------------------------------
>>>>>>
>>>>>> For better control / leverage, it's nice if you have a long-handle
>>>>>> combination wrench, like the 'pro' series one I picked up. It's even
>>>>>> nicer if you have the tool that holds the locknut and has a
>>>>>> screwdriver built it. GOOGLE 'powerbuilt 648828' or similar,
>>>>>> depending on the size of the '95's locknut. I have one but haven't
>>>>>> used it yet.
>>>>>>
>>>>>> 'Curly'
>>>>>
>>>>>
>>>>> I was going to use a torque wrench. That isn't critical?
>>>>>
>>>>
>>>>
>>>>
>>>>
>>>> It *most certainly* is.
>>>>
>>>> I do my valves every year. I use no special tools, just a flat-blade
>>>> screwdriver, a 12mm wrench and a feeler gauge set.
>>>>
>>>> The critical thing to do is to make certain the cam lobes you check are
>>>> pointing stright up to the sky. This ensures their ramps are nowhere
>>>> near the rocker mechanism, so cannot affect readings.
>>>>
>>>> Turn engine COUNTER-clockwise with your ratchet. If you have need to go
>>>> the other way, do that only for fine-tuning of cam position. Never turn
>>>> clockwise more than a degree or two.
>>>>
>>>
>>> I assume you mean a torque wrench with 12mm socket. ;-) I was hoping
>>> to turn the engine by rolling the car in gear. Any problem with that
>>> approach? I don't remember if the manual gives the bolt size - is 12mm
>>> applicable to my '95 EX?
>>
>>
>> There is no need for a torque wrench. In addition, you may want to
>> take a
>> look at one of my prior posts where I discuss the general technique for
>> adjusting valves. http://tinyurl.com/2bf5qf
>>
>> Eric
>
>
> There may not be a need for a torque wrench if you either have done
> the job before or instinctively know what 14 lb/ft feels like, but I'd
> prefer not to risk those aluminum rocker arms.
i don't think you should attempt this job at this time. it requires
experience and some degree of mechanical aptitude. judging by your
other posts and your reaction to responses, you don't appear to have
either. in fact, your motivation appears to be more recreational than
anything else.
if you're serious about learning, sign up for evening classes. otherwise
leave alone. a fouled up valve adjustment can cost you a lot of money.
#25
Guest
Posts: n/a
Re: How Hard is DIY Valve Adjustment?
mjc13<REMOVETHIS> wrote:
> Eric wrote:
>> "mjc13" wrote:
>>
>>> Tegger wrote:
>>>
>>>> "mjc13<REMOVETHIS>" <"mjc13<REMOVETHIS>"@verizon.net> wrote in
>>>> news:7uBgi.5806$bj5.2829@trndny07:
>>>>
>>>>
>>>>
>>>>> motsco_ wrote:
>>>>>
>>>>>
>>>>>> mjc13<REMOVETHIS> wrote:
>>>>>>
>>>>>>
>>>>>>
>>>>>>> Once again, this is a 1995 Civic EX 1.6L 125HP sedan. Don't have
>>>>>>> the serial number at hand. I've done valve lash adjustments on old
>>>>>>> Volvo pushrod engines, but nothing like this. It sounds like the
>>>>>>> adjustment mechanism is surprisingly similar, though: set screw and
>>>>>>> locknut. So, any tricks? Is this something best left to a seasoned
>>>>>>> mechanic? I have the Chilton manual.
>>>>>>
>>>>>>
>>>>>> ---------------------------------------
>>>>>>
>>>>>> For better control / leverage, it's nice if you have a long-handle
>>>>>> combination wrench, like the 'pro' series one I picked up. It's even
>>>>>> nicer if you have the tool that holds the locknut and has a
>>>>>> screwdriver built it. GOOGLE 'powerbuilt 648828' or similar,
>>>>>> depending on the size of the '95's locknut. I have one but haven't
>>>>>> used it yet.
>>>>>>
>>>>>> 'Curly'
>>>>>
>>>>>
>>>>> I was going to use a torque wrench. That isn't critical?
>>>>>
>>>>
>>>>
>>>>
>>>>
>>>> It *most certainly* is.
>>>>
>>>> I do my valves every year. I use no special tools, just a flat-blade
>>>> screwdriver, a 12mm wrench and a feeler gauge set.
>>>>
>>>> The critical thing to do is to make certain the cam lobes you check are
>>>> pointing stright up to the sky. This ensures their ramps are nowhere
>>>> near the rocker mechanism, so cannot affect readings.
>>>>
>>>> Turn engine COUNTER-clockwise with your ratchet. If you have need to go
>>>> the other way, do that only for fine-tuning of cam position. Never turn
>>>> clockwise more than a degree or two.
>>>>
>>>
>>> I assume you mean a torque wrench with 12mm socket. ;-) I was hoping
>>> to turn the engine by rolling the car in gear. Any problem with that
>>> approach? I don't remember if the manual gives the bolt size - is 12mm
>>> applicable to my '95 EX?
>>
>>
>> There is no need for a torque wrench. In addition, you may want to
>> take a
>> look at one of my prior posts where I discuss the general technique for
>> adjusting valves. http://tinyurl.com/2bf5qf
>>
>> Eric
>
>
> There may not be a need for a torque wrench if you either have done
> the job before or instinctively know what 14 lb/ft feels like, but I'd
> prefer not to risk those aluminum rocker arms.
i don't think you should attempt this job at this time. it requires
experience and some degree of mechanical aptitude. judging by your
other posts and your reaction to responses, you don't appear to have
either. in fact, your motivation appears to be more recreational than
anything else.
if you're serious about learning, sign up for evening classes. otherwise
leave alone. a fouled up valve adjustment can cost you a lot of money.
> Eric wrote:
>> "mjc13" wrote:
>>
>>> Tegger wrote:
>>>
>>>> "mjc13<REMOVETHIS>" <"mjc13<REMOVETHIS>"@verizon.net> wrote in
>>>> news:7uBgi.5806$bj5.2829@trndny07:
>>>>
>>>>
>>>>
>>>>> motsco_ wrote:
>>>>>
>>>>>
>>>>>> mjc13<REMOVETHIS> wrote:
>>>>>>
>>>>>>
>>>>>>
>>>>>>> Once again, this is a 1995 Civic EX 1.6L 125HP sedan. Don't have
>>>>>>> the serial number at hand. I've done valve lash adjustments on old
>>>>>>> Volvo pushrod engines, but nothing like this. It sounds like the
>>>>>>> adjustment mechanism is surprisingly similar, though: set screw and
>>>>>>> locknut. So, any tricks? Is this something best left to a seasoned
>>>>>>> mechanic? I have the Chilton manual.
>>>>>>
>>>>>>
>>>>>> ---------------------------------------
>>>>>>
>>>>>> For better control / leverage, it's nice if you have a long-handle
>>>>>> combination wrench, like the 'pro' series one I picked up. It's even
>>>>>> nicer if you have the tool that holds the locknut and has a
>>>>>> screwdriver built it. GOOGLE 'powerbuilt 648828' or similar,
>>>>>> depending on the size of the '95's locknut. I have one but haven't
>>>>>> used it yet.
>>>>>>
>>>>>> 'Curly'
>>>>>
>>>>>
>>>>> I was going to use a torque wrench. That isn't critical?
>>>>>
>>>>
>>>>
>>>>
>>>>
>>>> It *most certainly* is.
>>>>
>>>> I do my valves every year. I use no special tools, just a flat-blade
>>>> screwdriver, a 12mm wrench and a feeler gauge set.
>>>>
>>>> The critical thing to do is to make certain the cam lobes you check are
>>>> pointing stright up to the sky. This ensures their ramps are nowhere
>>>> near the rocker mechanism, so cannot affect readings.
>>>>
>>>> Turn engine COUNTER-clockwise with your ratchet. If you have need to go
>>>> the other way, do that only for fine-tuning of cam position. Never turn
>>>> clockwise more than a degree or two.
>>>>
>>>
>>> I assume you mean a torque wrench with 12mm socket. ;-) I was hoping
>>> to turn the engine by rolling the car in gear. Any problem with that
>>> approach? I don't remember if the manual gives the bolt size - is 12mm
>>> applicable to my '95 EX?
>>
>>
>> There is no need for a torque wrench. In addition, you may want to
>> take a
>> look at one of my prior posts where I discuss the general technique for
>> adjusting valves. http://tinyurl.com/2bf5qf
>>
>> Eric
>
>
> There may not be a need for a torque wrench if you either have done
> the job before or instinctively know what 14 lb/ft feels like, but I'd
> prefer not to risk those aluminum rocker arms.
i don't think you should attempt this job at this time. it requires
experience and some degree of mechanical aptitude. judging by your
other posts and your reaction to responses, you don't appear to have
either. in fact, your motivation appears to be more recreational than
anything else.
if you're serious about learning, sign up for evening classes. otherwise
leave alone. a fouled up valve adjustment can cost you a lot of money.
#26
Guest
Posts: n/a
Re: How Hard is DIY Valve Adjustment?
jim beam wrote:
> mjc13<REMOVETHIS> wrote:
>
>> Eric wrote:
>>
>>> "mjc13" wrote:
>>>
>>>> Tegger wrote:
>>>>
>>>>> "mjc13<REMOVETHIS>" <"mjc13<REMOVETHIS>"@verizon.net> wrote in
>>>>> news:7uBgi.5806$bj5.2829@trndny07:
>>>>>
>>>>>
>>>>>
>>>>>> motsco_ wrote:
>>>>>>
>>>>>>
>>>>>>> mjc13<REMOVETHIS> wrote:
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>> Once again, this is a 1995 Civic EX 1.6L 125HP sedan. Don't have
>>>>>>>> the serial number at hand. I've done valve lash adjustments on old
>>>>>>>> Volvo pushrod engines, but nothing like this. It sounds like the
>>>>>>>> adjustment mechanism is surprisingly similar, though: set screw and
>>>>>>>> locknut. So, any tricks? Is this something best left to a seasoned
>>>>>>>> mechanic? I have the Chilton manual.
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>> ---------------------------------------
>>>>>>>
>>>>>>> For better control / leverage, it's nice if you have a long-handle
>>>>>>> combination wrench, like the 'pro' series one I picked up. It's even
>>>>>>> nicer if you have the tool that holds the locknut and has a
>>>>>>> screwdriver built it. GOOGLE 'powerbuilt 648828' or similar,
>>>>>>> depending on the size of the '95's locknut. I have one but haven't
>>>>>>> used it yet.
>>>>>>>
>>>>>>> 'Curly'
>>>>>>
>>>>>>
>>>>>>
>>>>>> I was going to use a torque wrench. That isn't critical?
>>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>> It *most certainly* is.
>>>>>
>>>>> I do my valves every year. I use no special tools, just a flat-blade
>>>>> screwdriver, a 12mm wrench and a feeler gauge set.
>>>>>
>>>>> The critical thing to do is to make certain the cam lobes you check
>>>>> are
>>>>> pointing stright up to the sky. This ensures their ramps are nowhere
>>>>> near the rocker mechanism, so cannot affect readings.
>>>>>
>>>>> Turn engine COUNTER-clockwise with your ratchet. If you have need
>>>>> to go
>>>>> the other way, do that only for fine-tuning of cam position. Never
>>>>> turn
>>>>> clockwise more than a degree or two.
>>>>>
>>>>
>>>> I assume you mean a torque wrench with 12mm socket. ;-) I was hoping
>>>> to turn the engine by rolling the car in gear. Any problem with that
>>>> approach? I don't remember if the manual gives the bolt size - is 12mm
>>>> applicable to my '95 EX?
>>>
>>>
>>>
>>> There is no need for a torque wrench. In addition, you may want to
>>> take a
>>> look at one of my prior posts where I discuss the general technique for
>>> adjusting valves. http://tinyurl.com/2bf5qf
>>>
>>> Eric
>>
>>
>>
>> There may not be a need for a torque wrench if you either have done
>> the job before or instinctively know what 14 lb/ft feels like, but I'd
>> prefer not to risk those aluminum rocker arms.
>
>
>
>
> i don't think you should attempt this job at this time. it requires
> experience and some degree of mechanical aptitude. judging by your
> other posts and your reaction to responses, you don't appear to have
> either. in fact, your motivation appears to be more recreational than
> anything else.
>
> if you're serious about learning, sign up for evening classes. otherwise
> leave alone. a fouled up valve adjustment can cost you a lot of money.
I guess that establishes you as a troll. Before I filter you, I'll
again note that I've done valve adjustments - on steel rocker
assemblies, 30 years ago. Caution isn't the same as ineptitude, and
sarcasm isn't the same as wisdom.
> mjc13<REMOVETHIS> wrote:
>
>> Eric wrote:
>>
>>> "mjc13" wrote:
>>>
>>>> Tegger wrote:
>>>>
>>>>> "mjc13<REMOVETHIS>" <"mjc13<REMOVETHIS>"@verizon.net> wrote in
>>>>> news:7uBgi.5806$bj5.2829@trndny07:
>>>>>
>>>>>
>>>>>
>>>>>> motsco_ wrote:
>>>>>>
>>>>>>
>>>>>>> mjc13<REMOVETHIS> wrote:
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>> Once again, this is a 1995 Civic EX 1.6L 125HP sedan. Don't have
>>>>>>>> the serial number at hand. I've done valve lash adjustments on old
>>>>>>>> Volvo pushrod engines, but nothing like this. It sounds like the
>>>>>>>> adjustment mechanism is surprisingly similar, though: set screw and
>>>>>>>> locknut. So, any tricks? Is this something best left to a seasoned
>>>>>>>> mechanic? I have the Chilton manual.
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>> ---------------------------------------
>>>>>>>
>>>>>>> For better control / leverage, it's nice if you have a long-handle
>>>>>>> combination wrench, like the 'pro' series one I picked up. It's even
>>>>>>> nicer if you have the tool that holds the locknut and has a
>>>>>>> screwdriver built it. GOOGLE 'powerbuilt 648828' or similar,
>>>>>>> depending on the size of the '95's locknut. I have one but haven't
>>>>>>> used it yet.
>>>>>>>
>>>>>>> 'Curly'
>>>>>>
>>>>>>
>>>>>>
>>>>>> I was going to use a torque wrench. That isn't critical?
>>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>> It *most certainly* is.
>>>>>
>>>>> I do my valves every year. I use no special tools, just a flat-blade
>>>>> screwdriver, a 12mm wrench and a feeler gauge set.
>>>>>
>>>>> The critical thing to do is to make certain the cam lobes you check
>>>>> are
>>>>> pointing stright up to the sky. This ensures their ramps are nowhere
>>>>> near the rocker mechanism, so cannot affect readings.
>>>>>
>>>>> Turn engine COUNTER-clockwise with your ratchet. If you have need
>>>>> to go
>>>>> the other way, do that only for fine-tuning of cam position. Never
>>>>> turn
>>>>> clockwise more than a degree or two.
>>>>>
>>>>
>>>> I assume you mean a torque wrench with 12mm socket. ;-) I was hoping
>>>> to turn the engine by rolling the car in gear. Any problem with that
>>>> approach? I don't remember if the manual gives the bolt size - is 12mm
>>>> applicable to my '95 EX?
>>>
>>>
>>>
>>> There is no need for a torque wrench. In addition, you may want to
>>> take a
>>> look at one of my prior posts where I discuss the general technique for
>>> adjusting valves. http://tinyurl.com/2bf5qf
>>>
>>> Eric
>>
>>
>>
>> There may not be a need for a torque wrench if you either have done
>> the job before or instinctively know what 14 lb/ft feels like, but I'd
>> prefer not to risk those aluminum rocker arms.
>
>
>
>
> i don't think you should attempt this job at this time. it requires
> experience and some degree of mechanical aptitude. judging by your
> other posts and your reaction to responses, you don't appear to have
> either. in fact, your motivation appears to be more recreational than
> anything else.
>
> if you're serious about learning, sign up for evening classes. otherwise
> leave alone. a fouled up valve adjustment can cost you a lot of money.
I guess that establishes you as a troll. Before I filter you, I'll
again note that I've done valve adjustments - on steel rocker
assemblies, 30 years ago. Caution isn't the same as ineptitude, and
sarcasm isn't the same as wisdom.
#27
Guest
Posts: n/a
Re: How Hard is DIY Valve Adjustment?
jim beam wrote:
> mjc13<REMOVETHIS> wrote:
>
>> Eric wrote:
>>
>>> "mjc13" wrote:
>>>
>>>> Tegger wrote:
>>>>
>>>>> "mjc13<REMOVETHIS>" <"mjc13<REMOVETHIS>"@verizon.net> wrote in
>>>>> news:7uBgi.5806$bj5.2829@trndny07:
>>>>>
>>>>>
>>>>>
>>>>>> motsco_ wrote:
>>>>>>
>>>>>>
>>>>>>> mjc13<REMOVETHIS> wrote:
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>> Once again, this is a 1995 Civic EX 1.6L 125HP sedan. Don't have
>>>>>>>> the serial number at hand. I've done valve lash adjustments on old
>>>>>>>> Volvo pushrod engines, but nothing like this. It sounds like the
>>>>>>>> adjustment mechanism is surprisingly similar, though: set screw and
>>>>>>>> locknut. So, any tricks? Is this something best left to a seasoned
>>>>>>>> mechanic? I have the Chilton manual.
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>> ---------------------------------------
>>>>>>>
>>>>>>> For better control / leverage, it's nice if you have a long-handle
>>>>>>> combination wrench, like the 'pro' series one I picked up. It's even
>>>>>>> nicer if you have the tool that holds the locknut and has a
>>>>>>> screwdriver built it. GOOGLE 'powerbuilt 648828' or similar,
>>>>>>> depending on the size of the '95's locknut. I have one but haven't
>>>>>>> used it yet.
>>>>>>>
>>>>>>> 'Curly'
>>>>>>
>>>>>>
>>>>>>
>>>>>> I was going to use a torque wrench. That isn't critical?
>>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>> It *most certainly* is.
>>>>>
>>>>> I do my valves every year. I use no special tools, just a flat-blade
>>>>> screwdriver, a 12mm wrench and a feeler gauge set.
>>>>>
>>>>> The critical thing to do is to make certain the cam lobes you check
>>>>> are
>>>>> pointing stright up to the sky. This ensures their ramps are nowhere
>>>>> near the rocker mechanism, so cannot affect readings.
>>>>>
>>>>> Turn engine COUNTER-clockwise with your ratchet. If you have need
>>>>> to go
>>>>> the other way, do that only for fine-tuning of cam position. Never
>>>>> turn
>>>>> clockwise more than a degree or two.
>>>>>
>>>>
>>>> I assume you mean a torque wrench with 12mm socket. ;-) I was hoping
>>>> to turn the engine by rolling the car in gear. Any problem with that
>>>> approach? I don't remember if the manual gives the bolt size - is 12mm
>>>> applicable to my '95 EX?
>>>
>>>
>>>
>>> There is no need for a torque wrench. In addition, you may want to
>>> take a
>>> look at one of my prior posts where I discuss the general technique for
>>> adjusting valves. http://tinyurl.com/2bf5qf
>>>
>>> Eric
>>
>>
>>
>> There may not be a need for a torque wrench if you either have done
>> the job before or instinctively know what 14 lb/ft feels like, but I'd
>> prefer not to risk those aluminum rocker arms.
>
>
>
>
> i don't think you should attempt this job at this time. it requires
> experience and some degree of mechanical aptitude. judging by your
> other posts and your reaction to responses, you don't appear to have
> either. in fact, your motivation appears to be more recreational than
> anything else.
>
> if you're serious about learning, sign up for evening classes. otherwise
> leave alone. a fouled up valve adjustment can cost you a lot of money.
I guess that establishes you as a troll. Before I filter you, I'll
again note that I've done valve adjustments - on steel rocker
assemblies, 30 years ago. Caution isn't the same as ineptitude, and
sarcasm isn't the same as wisdom.
> mjc13<REMOVETHIS> wrote:
>
>> Eric wrote:
>>
>>> "mjc13" wrote:
>>>
>>>> Tegger wrote:
>>>>
>>>>> "mjc13<REMOVETHIS>" <"mjc13<REMOVETHIS>"@verizon.net> wrote in
>>>>> news:7uBgi.5806$bj5.2829@trndny07:
>>>>>
>>>>>
>>>>>
>>>>>> motsco_ wrote:
>>>>>>
>>>>>>
>>>>>>> mjc13<REMOVETHIS> wrote:
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>> Once again, this is a 1995 Civic EX 1.6L 125HP sedan. Don't have
>>>>>>>> the serial number at hand. I've done valve lash adjustments on old
>>>>>>>> Volvo pushrod engines, but nothing like this. It sounds like the
>>>>>>>> adjustment mechanism is surprisingly similar, though: set screw and
>>>>>>>> locknut. So, any tricks? Is this something best left to a seasoned
>>>>>>>> mechanic? I have the Chilton manual.
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>> ---------------------------------------
>>>>>>>
>>>>>>> For better control / leverage, it's nice if you have a long-handle
>>>>>>> combination wrench, like the 'pro' series one I picked up. It's even
>>>>>>> nicer if you have the tool that holds the locknut and has a
>>>>>>> screwdriver built it. GOOGLE 'powerbuilt 648828' or similar,
>>>>>>> depending on the size of the '95's locknut. I have one but haven't
>>>>>>> used it yet.
>>>>>>>
>>>>>>> 'Curly'
>>>>>>
>>>>>>
>>>>>>
>>>>>> I was going to use a torque wrench. That isn't critical?
>>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>> It *most certainly* is.
>>>>>
>>>>> I do my valves every year. I use no special tools, just a flat-blade
>>>>> screwdriver, a 12mm wrench and a feeler gauge set.
>>>>>
>>>>> The critical thing to do is to make certain the cam lobes you check
>>>>> are
>>>>> pointing stright up to the sky. This ensures their ramps are nowhere
>>>>> near the rocker mechanism, so cannot affect readings.
>>>>>
>>>>> Turn engine COUNTER-clockwise with your ratchet. If you have need
>>>>> to go
>>>>> the other way, do that only for fine-tuning of cam position. Never
>>>>> turn
>>>>> clockwise more than a degree or two.
>>>>>
>>>>
>>>> I assume you mean a torque wrench with 12mm socket. ;-) I was hoping
>>>> to turn the engine by rolling the car in gear. Any problem with that
>>>> approach? I don't remember if the manual gives the bolt size - is 12mm
>>>> applicable to my '95 EX?
>>>
>>>
>>>
>>> There is no need for a torque wrench. In addition, you may want to
>>> take a
>>> look at one of my prior posts where I discuss the general technique for
>>> adjusting valves. http://tinyurl.com/2bf5qf
>>>
>>> Eric
>>
>>
>>
>> There may not be a need for a torque wrench if you either have done
>> the job before or instinctively know what 14 lb/ft feels like, but I'd
>> prefer not to risk those aluminum rocker arms.
>
>
>
>
> i don't think you should attempt this job at this time. it requires
> experience and some degree of mechanical aptitude. judging by your
> other posts and your reaction to responses, you don't appear to have
> either. in fact, your motivation appears to be more recreational than
> anything else.
>
> if you're serious about learning, sign up for evening classes. otherwise
> leave alone. a fouled up valve adjustment can cost you a lot of money.
I guess that establishes you as a troll. Before I filter you, I'll
again note that I've done valve adjustments - on steel rocker
assemblies, 30 years ago. Caution isn't the same as ineptitude, and
sarcasm isn't the same as wisdom.
#28
Guest
Posts: n/a
Re: How Hard is DIY Valve Adjustment?
jim beam wrote:
> mjc13<REMOVETHIS> wrote:
>
>> Eric wrote:
>>
>>> "mjc13" wrote:
>>>
>>>> Tegger wrote:
>>>>
>>>>> "mjc13<REMOVETHIS>" <"mjc13<REMOVETHIS>"@verizon.net> wrote in
>>>>> news:7uBgi.5806$bj5.2829@trndny07:
>>>>>
>>>>>
>>>>>
>>>>>> motsco_ wrote:
>>>>>>
>>>>>>
>>>>>>> mjc13<REMOVETHIS> wrote:
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>> Once again, this is a 1995 Civic EX 1.6L 125HP sedan. Don't have
>>>>>>>> the serial number at hand. I've done valve lash adjustments on old
>>>>>>>> Volvo pushrod engines, but nothing like this. It sounds like the
>>>>>>>> adjustment mechanism is surprisingly similar, though: set screw and
>>>>>>>> locknut. So, any tricks? Is this something best left to a seasoned
>>>>>>>> mechanic? I have the Chilton manual.
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>> ---------------------------------------
>>>>>>>
>>>>>>> For better control / leverage, it's nice if you have a long-handle
>>>>>>> combination wrench, like the 'pro' series one I picked up. It's even
>>>>>>> nicer if you have the tool that holds the locknut and has a
>>>>>>> screwdriver built it. GOOGLE 'powerbuilt 648828' or similar,
>>>>>>> depending on the size of the '95's locknut. I have one but haven't
>>>>>>> used it yet.
>>>>>>>
>>>>>>> 'Curly'
>>>>>>
>>>>>>
>>>>>>
>>>>>> I was going to use a torque wrench. That isn't critical?
>>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>> It *most certainly* is.
>>>>>
>>>>> I do my valves every year. I use no special tools, just a flat-blade
>>>>> screwdriver, a 12mm wrench and a feeler gauge set.
>>>>>
>>>>> The critical thing to do is to make certain the cam lobes you check
>>>>> are
>>>>> pointing stright up to the sky. This ensures their ramps are nowhere
>>>>> near the rocker mechanism, so cannot affect readings.
>>>>>
>>>>> Turn engine COUNTER-clockwise with your ratchet. If you have need
>>>>> to go
>>>>> the other way, do that only for fine-tuning of cam position. Never
>>>>> turn
>>>>> clockwise more than a degree or two.
>>>>>
>>>>
>>>> I assume you mean a torque wrench with 12mm socket. ;-) I was hoping
>>>> to turn the engine by rolling the car in gear. Any problem with that
>>>> approach? I don't remember if the manual gives the bolt size - is 12mm
>>>> applicable to my '95 EX?
>>>
>>>
>>>
>>> There is no need for a torque wrench. In addition, you may want to
>>> take a
>>> look at one of my prior posts where I discuss the general technique for
>>> adjusting valves. http://tinyurl.com/2bf5qf
>>>
>>> Eric
>>
>>
>>
>> There may not be a need for a torque wrench if you either have done
>> the job before or instinctively know what 14 lb/ft feels like, but I'd
>> prefer not to risk those aluminum rocker arms.
>
>
>
>
> i don't think you should attempt this job at this time. it requires
> experience and some degree of mechanical aptitude. judging by your
> other posts and your reaction to responses, you don't appear to have
> either. in fact, your motivation appears to be more recreational than
> anything else.
>
> if you're serious about learning, sign up for evening classes. otherwise
> leave alone. a fouled up valve adjustment can cost you a lot of money.
I guess that establishes you as a troll. Before I filter you, I'll
again note that I've done valve adjustments - on steel rocker
assemblies, 30 years ago. Caution isn't the same as ineptitude, and
sarcasm isn't the same as wisdom.
> mjc13<REMOVETHIS> wrote:
>
>> Eric wrote:
>>
>>> "mjc13" wrote:
>>>
>>>> Tegger wrote:
>>>>
>>>>> "mjc13<REMOVETHIS>" <"mjc13<REMOVETHIS>"@verizon.net> wrote in
>>>>> news:7uBgi.5806$bj5.2829@trndny07:
>>>>>
>>>>>
>>>>>
>>>>>> motsco_ wrote:
>>>>>>
>>>>>>
>>>>>>> mjc13<REMOVETHIS> wrote:
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>> Once again, this is a 1995 Civic EX 1.6L 125HP sedan. Don't have
>>>>>>>> the serial number at hand. I've done valve lash adjustments on old
>>>>>>>> Volvo pushrod engines, but nothing like this. It sounds like the
>>>>>>>> adjustment mechanism is surprisingly similar, though: set screw and
>>>>>>>> locknut. So, any tricks? Is this something best left to a seasoned
>>>>>>>> mechanic? I have the Chilton manual.
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>> ---------------------------------------
>>>>>>>
>>>>>>> For better control / leverage, it's nice if you have a long-handle
>>>>>>> combination wrench, like the 'pro' series one I picked up. It's even
>>>>>>> nicer if you have the tool that holds the locknut and has a
>>>>>>> screwdriver built it. GOOGLE 'powerbuilt 648828' or similar,
>>>>>>> depending on the size of the '95's locknut. I have one but haven't
>>>>>>> used it yet.
>>>>>>>
>>>>>>> 'Curly'
>>>>>>
>>>>>>
>>>>>>
>>>>>> I was going to use a torque wrench. That isn't critical?
>>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>> It *most certainly* is.
>>>>>
>>>>> I do my valves every year. I use no special tools, just a flat-blade
>>>>> screwdriver, a 12mm wrench and a feeler gauge set.
>>>>>
>>>>> The critical thing to do is to make certain the cam lobes you check
>>>>> are
>>>>> pointing stright up to the sky. This ensures their ramps are nowhere
>>>>> near the rocker mechanism, so cannot affect readings.
>>>>>
>>>>> Turn engine COUNTER-clockwise with your ratchet. If you have need
>>>>> to go
>>>>> the other way, do that only for fine-tuning of cam position. Never
>>>>> turn
>>>>> clockwise more than a degree or two.
>>>>>
>>>>
>>>> I assume you mean a torque wrench with 12mm socket. ;-) I was hoping
>>>> to turn the engine by rolling the car in gear. Any problem with that
>>>> approach? I don't remember if the manual gives the bolt size - is 12mm
>>>> applicable to my '95 EX?
>>>
>>>
>>>
>>> There is no need for a torque wrench. In addition, you may want to
>>> take a
>>> look at one of my prior posts where I discuss the general technique for
>>> adjusting valves. http://tinyurl.com/2bf5qf
>>>
>>> Eric
>>
>>
>>
>> There may not be a need for a torque wrench if you either have done
>> the job before or instinctively know what 14 lb/ft feels like, but I'd
>> prefer not to risk those aluminum rocker arms.
>
>
>
>
> i don't think you should attempt this job at this time. it requires
> experience and some degree of mechanical aptitude. judging by your
> other posts and your reaction to responses, you don't appear to have
> either. in fact, your motivation appears to be more recreational than
> anything else.
>
> if you're serious about learning, sign up for evening classes. otherwise
> leave alone. a fouled up valve adjustment can cost you a lot of money.
I guess that establishes you as a troll. Before I filter you, I'll
again note that I've done valve adjustments - on steel rocker
assemblies, 30 years ago. Caution isn't the same as ineptitude, and
sarcasm isn't the same as wisdom.
#29
Guest
Posts: n/a
Re: How Hard is DIY Valve Adjustment?
"mjc13<REMOVETHIS>" <"mjc13<REMOVETHIS>"@verizon.net> wrote in
news:R0Ggi.13395$oo5.5736@trndny09:
>>
>
> I assume you mean a torque wrench with 12mm socket. ;-) I was
> hoping
> to turn the engine by rolling the car in gear. Any problem with that
> approach? I don't remember if the manual gives the bolt size - is 12mm
> applicable to my '95 EX?
You really, really, need a good shop manual. You clearly have no idea
what's involved.
www.helminc.com
Turn the steering wheel all the way to the left. Now get down and peek
inside the wheel well at the splash shield inboard of the wheel. See the
big round rubber plug? Pop that out and you can use a 19mm socket on a long
extension to turn the engine counterclockwise.
The 12mm wrench is for loosening and tightening the locknuts that hold the
valve adjustment. The screwdriver is for the threaded adjusters.
The torque wrench (and 12mm socket) is for making sure the locknuts are
snugged up properly and will not vibrate loose on you.
--
Tegger
The Unofficial Honda/Acura FAQ
www.tegger.com/hondafaq/
news:R0Ggi.13395$oo5.5736@trndny09:
>>
>
> I assume you mean a torque wrench with 12mm socket. ;-) I was
> hoping
> to turn the engine by rolling the car in gear. Any problem with that
> approach? I don't remember if the manual gives the bolt size - is 12mm
> applicable to my '95 EX?
You really, really, need a good shop manual. You clearly have no idea
what's involved.
www.helminc.com
Turn the steering wheel all the way to the left. Now get down and peek
inside the wheel well at the splash shield inboard of the wheel. See the
big round rubber plug? Pop that out and you can use a 19mm socket on a long
extension to turn the engine counterclockwise.
The 12mm wrench is for loosening and tightening the locknuts that hold the
valve adjustment. The screwdriver is for the threaded adjusters.
The torque wrench (and 12mm socket) is for making sure the locknuts are
snugged up properly and will not vibrate loose on you.
--
Tegger
The Unofficial Honda/Acura FAQ
www.tegger.com/hondafaq/
#30
Guest
Posts: n/a
Re: How Hard is DIY Valve Adjustment?
"mjc13<REMOVETHIS>" <"mjc13<REMOVETHIS>"@verizon.net> wrote in
news:R0Ggi.13395$oo5.5736@trndny09:
>>
>
> I assume you mean a torque wrench with 12mm socket. ;-) I was
> hoping
> to turn the engine by rolling the car in gear. Any problem with that
> approach? I don't remember if the manual gives the bolt size - is 12mm
> applicable to my '95 EX?
You really, really, need a good shop manual. You clearly have no idea
what's involved.
www.helminc.com
Turn the steering wheel all the way to the left. Now get down and peek
inside the wheel well at the splash shield inboard of the wheel. See the
big round rubber plug? Pop that out and you can use a 19mm socket on a long
extension to turn the engine counterclockwise.
The 12mm wrench is for loosening and tightening the locknuts that hold the
valve adjustment. The screwdriver is for the threaded adjusters.
The torque wrench (and 12mm socket) is for making sure the locknuts are
snugged up properly and will not vibrate loose on you.
--
Tegger
The Unofficial Honda/Acura FAQ
www.tegger.com/hondafaq/
news:R0Ggi.13395$oo5.5736@trndny09:
>>
>
> I assume you mean a torque wrench with 12mm socket. ;-) I was
> hoping
> to turn the engine by rolling the car in gear. Any problem with that
> approach? I don't remember if the manual gives the bolt size - is 12mm
> applicable to my '95 EX?
You really, really, need a good shop manual. You clearly have no idea
what's involved.
www.helminc.com
Turn the steering wheel all the way to the left. Now get down and peek
inside the wheel well at the splash shield inboard of the wheel. See the
big round rubber plug? Pop that out and you can use a 19mm socket on a long
extension to turn the engine counterclockwise.
The 12mm wrench is for loosening and tightening the locknuts that hold the
valve adjustment. The screwdriver is for the threaded adjusters.
The torque wrench (and 12mm socket) is for making sure the locknuts are
snugged up properly and will not vibrate loose on you.
--
Tegger
The Unofficial Honda/Acura FAQ
www.tegger.com/hondafaq/