Left Upper Control Arm Replacement
12-17-2005, 07:34 AM
#1
Guest
Posts: n/a
Left Upper Control Arm Replacement
The ball joint on the upper left control arm on my 92 Accord is bad and
needs to be replaced, the control arm that is. I'm considering doing
this myself. Has anyone one out there ever replaced on? Any comments on
how hard it is to do?
Thanks
needs to be replaced, the control arm that is. I'm considering doing
this myself. Has anyone one out there ever replaced on? Any comments on
how hard it is to do?
Thanks
12-17-2005, 07:53 AM
#2
Guest
Posts: n/a
Re: Left Upper Control Arm Replacement
"Face" <face@yahoo.com> wrote in message
news:face-553982.07342917122005@news-rdr-03.ohiordc.rr.com...
> The ball joint on the upper left control arm on my 92 Accord is bad and
> needs to be replaced, the control arm that is. I'm considering doing
> this myself. Has anyone one out there ever replaced on? Any comments on
> how hard it is to do?
>
> Thanks
The tough part undoubtedly will be separating the ball joint. I bought a
separator on-line at
http://www.etoolcart.com/index.asp?P...OD&ProdID=6556
and it works well, but others have found similar devices for more like the
$20 range IIRC. A pickle fork would work in a pinch since you are replacing
the joint and don't care what happens to the old one, but they can be
frustrating, too.
The Haynes manual warns the steering knuckle and upper control arm have a
lot of tension between them, so they advise leaving the nut loosely on the
ball joint stud as you separate it. In addition, it recommends wiring the
top of the knuckle to the shock absorber to prevent it from tipping sharply
when the ball joint is separated.
Otherwise, it looks pretty straightforward. Now, for feedback from people
who have actually *done* the job....
Mike
news:face-553982.07342917122005@news-rdr-03.ohiordc.rr.com...
> The ball joint on the upper left control arm on my 92 Accord is bad and
> needs to be replaced, the control arm that is. I'm considering doing
> this myself. Has anyone one out there ever replaced on? Any comments on
> how hard it is to do?
>
> Thanks
The tough part undoubtedly will be separating the ball joint. I bought a
separator on-line at
http://www.etoolcart.com/index.asp?P...OD&ProdID=6556
and it works well, but others have found similar devices for more like the
$20 range IIRC. A pickle fork would work in a pinch since you are replacing
the joint and don't care what happens to the old one, but they can be
frustrating, too.
The Haynes manual warns the steering knuckle and upper control arm have a
lot of tension between them, so they advise leaving the nut loosely on the
ball joint stud as you separate it. In addition, it recommends wiring the
top of the knuckle to the shock absorber to prevent it from tipping sharply
when the ball joint is separated.
Otherwise, it looks pretty straightforward. Now, for feedback from people
who have actually *done* the job....
Mike
12-17-2005, 11:21 AM
#3
Guest
Posts: n/a
Re: Left Upper Control Arm Replacement
Michael Pardee wrote:
>
> "Face" <face@yahoo.com> wrote in message
> news:face-553982.07342917122005@news-rdr-03.ohiordc.rr.com...
> > The ball joint on the upper left control arm on my 92 Accord is bad and
> > needs to be replaced, the control arm that is. I'm considering doing
> > this myself. Has anyone one out there ever replaced on? Any comments on
> > how hard it is to do?
> >
> > Thanks
>
> The tough part undoubtedly will be separating the ball joint. I bought a
> separator on-line at
> http://www.etoolcart.com/index.asp?P...OD&ProdID=6556
> and it works well, but others have found similar devices for more like the
> $20 range IIRC. A pickle fork would work in a pinch since you are replacing
> the joint and don't care what happens to the old one, but they can be
> frustrating, too.
>
> The Haynes manual warns the steering knuckle and upper control arm have a
> lot of tension between them, so they advise leaving the nut loosely on the
> ball joint stud as you separate it. In addition, it recommends wiring the
> top of the knuckle to the shock absorber to prevent it from tipping sharply
> when the ball joint is separated.
>
> Otherwise, it looks pretty straightforward. Now, for feedback from people
> who have actually *done* the job....
>
> Mike
-----------------------------
Some good tips there . . . I did two of them on a CR-V a while ago and
there's no tension on the upper. The separator is available at places
that carry the Whun-Hung-Low imported tools. In Canada Princess Auto has
them for $20. Made in taiwan. It took about 45 minutes to swap out the
upper arm and I was able to keep the old part (moved it to another CR-V)
since the special tool doesn't wreck the boot.
'Curly'
>
> "Face" <face@yahoo.com> wrote in message
> news:face-553982.07342917122005@news-rdr-03.ohiordc.rr.com...
> > The ball joint on the upper left control arm on my 92 Accord is bad and
> > needs to be replaced, the control arm that is. I'm considering doing
> > this myself. Has anyone one out there ever replaced on? Any comments on
> > how hard it is to do?
> >
> > Thanks
>
> The tough part undoubtedly will be separating the ball joint. I bought a
> separator on-line at
> http://www.etoolcart.com/index.asp?P...OD&ProdID=6556
> and it works well, but others have found similar devices for more like the
> $20 range IIRC. A pickle fork would work in a pinch since you are replacing
> the joint and don't care what happens to the old one, but they can be
> frustrating, too.
>
> The Haynes manual warns the steering knuckle and upper control arm have a
> lot of tension between them, so they advise leaving the nut loosely on the
> ball joint stud as you separate it. In addition, it recommends wiring the
> top of the knuckle to the shock absorber to prevent it from tipping sharply
> when the ball joint is separated.
>
> Otherwise, it looks pretty straightforward. Now, for feedback from people
> who have actually *done* the job....
>
> Mike
-----------------------------
Some good tips there . . . I did two of them on a CR-V a while ago and
there's no tension on the upper. The separator is available at places
that carry the Whun-Hung-Low imported tools. In Canada Princess Auto has
them for $20. Made in taiwan. It took about 45 minutes to swap out the
upper arm and I was able to keep the old part (moved it to another CR-V)
since the special tool doesn't wreck the boot.
'Curly'
12-17-2005, 11:34 AM
#4
Guest
Posts: n/a
Re: Left Upper Control Arm Replacement
"'Curly Q. Links'" <motsco__@interbaun.com> wrote in message
news:43A43AFA.5DA8B7CE@interbaun.com...
> Michael Pardee wrote:
>>
>> "Face" <face@yahoo.com> wrote in message
>> news:face-553982.07342917122005@news-rdr-03.ohiordc.rr.com...
>> > The ball joint on the upper left control arm on my 92 Accord is bad and
>> > needs to be replaced, the control arm that is. I'm considering doing
>> > this myself. Has anyone one out there ever replaced on? Any comments
>> > on
>> > how hard it is to do?
>> >
>> > Thanks
>>
>> The tough part undoubtedly will be separating the ball joint. I bought a
>> separator on-line at
>> http://www.etoolcart.com/index.asp?P...OD&ProdID=6556
>> and it works well, but others have found similar devices for more like
>> the
>> $20 range IIRC. A pickle fork would work in a pinch since you are
>> replacing
>> the joint and don't care what happens to the old one, but they can be
>> frustrating, too.
>>
>> The Haynes manual warns the steering knuckle and upper control arm have a
>> lot of tension between them, so they advise leaving the nut loosely on
>> the
>> ball joint stud as you separate it. In addition, it recommends wiring the
>> top of the knuckle to the shock absorber to prevent it from tipping
>> sharply
>> when the ball joint is separated.
>>
>> Otherwise, it looks pretty straightforward. Now, for feedback from people
>> who have actually *done* the job....
>>
>> Mike
>
> -----------------------------
>
> Some good tips there . . . I did two of them on a CR-V a while ago and
> there's no tension on the upper. The separator is available at places
> that carry the Whun-Hung-Low imported tools. In Canada Princess Auto has
> them for $20. Made in taiwan. It took about 45 minutes to swap out the
> upper arm and I was able to keep the old part (moved it to another CR-V)
> since the special tool doesn't wreck the boot.
>
> 'Curly'
I've bought and used the 20.00 Princess auto ball joint popper.
Makes me wonder why I didn't buy one of these decades ago!
12-17-2005, 12:45 PM
#5
Guest
Posts: n/a
Re: Left Upper Control Arm Replacement
Skim the popular site
http://www.tegger.com/hondafaq/faq.html#balljoints .
"Face" <face@yahoo.com> wrote
> The ball joint on the upper left control arm on my 92
Accord is bad and
> needs to be replaced, the control arm that is. I'm
considering doing
> this myself. Has anyone one out there ever replaced on?
Any comments on
> how hard it is to do?
http://www.tegger.com/hondafaq/faq.html#balljoints .
"Face" <face@yahoo.com> wrote
> The ball joint on the upper left control arm on my 92
Accord is bad and
> needs to be replaced, the control arm that is. I'm
considering doing
> this myself. Has anyone one out there ever replaced on?
Any comments on
> how hard it is to do?
12-17-2005, 01:03 PM
#6
Guest
Posts: n/a
Re: Left Upper Control Arm Replacement
If your that concerned about tension between the steering knuckle and the
upper control arm, just put a jack underneath the lower control arm and raise
it about 1/2 an inch.
Also, if you just gonna trash the upper control arm, you can just use a
pickle fork (small one) to separate the ball joint. The special tool is very
useful if you are concerned with salvaging the rubber boot on the upper ball
joint. Just get the pickle fork started and start whaling on it. Its quite
therapeutic actually.....
I've done the job twice on my 98 civic. First time it took 40 minutes.
Second time it took 10.
MAKE SURE you torque the tower bolts correctly, and MAKE SURE you seat the
new upper ball joint in its taper properly too (proper torque is ESSENTIAL or
you get all sorts of funny noises if it works itself out of its taper).
Don't overtighten either, I've busted ball joint studs by doing that too.
Use a torque wrench!
On my civic, I believe the torque was 90 ftlbs on the tower bolts and 60 on
the ball joint castle nut.
t
Steve Bigelow wrote:
>>> > The ball joint on the upper left control arm on my 92 Accord is bad and
>>> > needs to be replaced, the control arm that is. I'm considering doing
>[quoted text clipped - 37 lines]
>>
>> 'Curly'
>
>I've bought and used the 20.00 Princess auto ball joint popper.
>Makes me wonder why I didn't buy one of these decades ago!
--
Message posted via http://www.carkb.com
upper control arm, just put a jack underneath the lower control arm and raise
it about 1/2 an inch.
Also, if you just gonna trash the upper control arm, you can just use a
pickle fork (small one) to separate the ball joint. The special tool is very
useful if you are concerned with salvaging the rubber boot on the upper ball
joint. Just get the pickle fork started and start whaling on it. Its quite
therapeutic actually.....
I've done the job twice on my 98 civic. First time it took 40 minutes.
Second time it took 10.
MAKE SURE you torque the tower bolts correctly, and MAKE SURE you seat the
new upper ball joint in its taper properly too (proper torque is ESSENTIAL or
you get all sorts of funny noises if it works itself out of its taper).
Don't overtighten either, I've busted ball joint studs by doing that too.
Use a torque wrench!
On my civic, I believe the torque was 90 ftlbs on the tower bolts and 60 on
the ball joint castle nut.
t
Steve Bigelow wrote:
>>> > The ball joint on the upper left control arm on my 92 Accord is bad and
>>> > needs to be replaced, the control arm that is. I'm considering doing
>[quoted text clipped - 37 lines]
>>
>> 'Curly'
>
>I've bought and used the 20.00 Princess auto ball joint popper.
>Makes me wonder why I didn't buy one of these decades ago!
--
Message posted via http://www.carkb.com
12-18-2005, 12:13 AM
#7
Guest
Posts: n/a
Re: Left Upper Control Arm Replacement
Steve Bigelow wrote:
>
> "'Curly Q. Links'" <motsco__@interbaun.com> wrote in message
> news:43A43AFA.5DA8B7CE@interbaun.com...
> > Michael Pardee wrote:
> >>
> >> "Face" <face@yahoo.com> wrote in message
> >> news:face-553982.07342917122005@news-rdr-03.ohiordc.rr.com...
> >> > The ball joint on the upper left control arm on my 92 Accord is bad and
> >> > needs to be replaced, the control arm that is. I'm considering doing
> >> > this myself. Has anyone one out there ever replaced on? Any comments
> >> > on
> >> > how hard it is to do?
> >> >
> >> > Thanks
> >>
> >> The tough part undoubtedly will be separating the ball joint. I bought a
> >> separator on-line at
> >> http://www.etoolcart.com/index.asp?P...OD&ProdID=6556
> >> and it works well, but others have found similar devices for more like
> >> the
> >> $20 range IIRC. A pickle fork would work in a pinch since you are
> >> replacing
> >> the joint and don't care what happens to the old one, but they can be
> >> frustrating, too.
> >>
> >> The Haynes manual warns the steering knuckle and upper control arm have a
> >> lot of tension between them, so they advise leaving the nut loosely on
> >> the
> >> ball joint stud as you separate it. In addition, it recommends wiring the
> >> top of the knuckle to the shock absorber to prevent it from tipping
> >> sharply
> >> when the ball joint is separated.
> >>
> >> Otherwise, it looks pretty straightforward. Now, for feedback from people
> >> who have actually *done* the job....
> >>
> >> Mike
> >
> > -----------------------------
> >
> > Some good tips there . . . I did two of them on a CR-V a while ago and
> > there's no tension on the upper. The separator is available at places
> > that carry the Whun-Hung-Low imported tools. In Canada Princess Auto has
> > them for $20. Made in taiwan. It took about 45 minutes to swap out the
> > upper arm and I was able to keep the old part (moved it to another CR-V)
> > since the special tool doesn't wreck the boot.
> >
> > 'Curly'
>
> I've bought and used the 20.00 Princess auto ball joint popper.
> Makes me wonder why I didn't buy one of these decades ago!
------------------------------------
Because they've always been about $60CAN ???
++++++++++++++++++++++++++
I was there tonight and they are on sale for $16.99. I paid $63 for the
'real ' one a year ago. Think it's DTC or something. The one shown in
the Honda manual is much thinner so it really gets under the boot
better. Maybe I'll buy myself the Princess Auto 'stocking stuffer'
version and grind it down just like the one in the Honda manual. Way
less stressful when you don't have to worry about chopping up the boot.
'Curly'
>
> "'Curly Q. Links'" <motsco__@interbaun.com> wrote in message
> news:43A43AFA.5DA8B7CE@interbaun.com...
> > Michael Pardee wrote:
> >>
> >> "Face" <face@yahoo.com> wrote in message
> >> news:face-553982.07342917122005@news-rdr-03.ohiordc.rr.com...
> >> > The ball joint on the upper left control arm on my 92 Accord is bad and
> >> > needs to be replaced, the control arm that is. I'm considering doing
> >> > this myself. Has anyone one out there ever replaced on? Any comments
> >> > on
> >> > how hard it is to do?
> >> >
> >> > Thanks
> >>
> >> The tough part undoubtedly will be separating the ball joint. I bought a
> >> separator on-line at
> >> http://www.etoolcart.com/index.asp?P...OD&ProdID=6556
> >> and it works well, but others have found similar devices for more like
> >> the
> >> $20 range IIRC. A pickle fork would work in a pinch since you are
> >> replacing
> >> the joint and don't care what happens to the old one, but they can be
> >> frustrating, too.
> >>
> >> The Haynes manual warns the steering knuckle and upper control arm have a
> >> lot of tension between them, so they advise leaving the nut loosely on
> >> the
> >> ball joint stud as you separate it. In addition, it recommends wiring the
> >> top of the knuckle to the shock absorber to prevent it from tipping
> >> sharply
> >> when the ball joint is separated.
> >>
> >> Otherwise, it looks pretty straightforward. Now, for feedback from people
> >> who have actually *done* the job....
> >>
> >> Mike
> >
> > -----------------------------
> >
> > Some good tips there . . . I did two of them on a CR-V a while ago and
> > there's no tension on the upper. The separator is available at places
> > that carry the Whun-Hung-Low imported tools. In Canada Princess Auto has
> > them for $20. Made in taiwan. It took about 45 minutes to swap out the
> > upper arm and I was able to keep the old part (moved it to another CR-V)
> > since the special tool doesn't wreck the boot.
> >
> > 'Curly'
>
> I've bought and used the 20.00 Princess auto ball joint popper.
> Makes me wonder why I didn't buy one of these decades ago!
------------------------------------
Because they've always been about $60CAN ???
++++++++++++++++++++++++++
I was there tonight and they are on sale for $16.99. I paid $63 for the
'real ' one a year ago. Think it's DTC or something. The one shown in
the Honda manual is much thinner so it really gets under the boot
better. Maybe I'll buy myself the Princess Auto 'stocking stuffer'
version and grind it down just like the one in the Honda manual. Way
less stressful when you don't have to worry about chopping up the boot.
'Curly'
12-18-2005, 08:31 AM
#8
Guest
Posts: n/a
Re: Left Upper Control Arm Replacement
"'Curly Q. Links'" <motsco__@interbaun.com> wrote in message
news:43A4EFEE.37FDB604@interbaun.com...
> Steve Bigelow wrote:
>>
>> "'Curly Q. Links'" <motsco__@interbaun.com> wrote in message
>> news:43A43AFA.5DA8B7CE@interbaun.com...
>> > Michael Pardee wrote:
>> >>
>> >> "Face" <face@yahoo.com> wrote in message
>> >> news:face-553982.07342917122005@news-rdr-03.ohiordc.rr.com...
>> >> > The ball joint on the upper left control arm on my 92 Accord is bad
>> >> > and
>> >> > needs to be replaced, the control arm that is. I'm considering
>> >> > doing
>> >> > this myself. Has anyone one out there ever replaced on? Any
>> >> > comments
>> >> > on
>> >> > how hard it is to do?
>> >> >
>> >> > Thanks
>> >>
>> >> The tough part undoubtedly will be separating the ball joint. I bought
>> >> a
>> >> separator on-line at
>> >> http://www.etoolcart.com/index.asp?P...OD&ProdID=6556
>> >> and it works well, but others have found similar devices for more like
>> >> the
>> >> $20 range IIRC. A pickle fork would work in a pinch since you are
>> >> replacing
>> >> the joint and don't care what happens to the old one, but they can be
>> >> frustrating, too.
>> >>
>> >> The Haynes manual warns the steering knuckle and upper control arm
>> >> have a
>> >> lot of tension between them, so they advise leaving the nut loosely on
>> >> the
>> >> ball joint stud as you separate it. In addition, it recommends wiring
>> >> the
>> >> top of the knuckle to the shock absorber to prevent it from tipping
>> >> sharply
>> >> when the ball joint is separated.
>> >>
>> >> Otherwise, it looks pretty straightforward. Now, for feedback from
>> >> people
>> >> who have actually *done* the job....
>> >>
>> >> Mike
>> >
>> > -----------------------------
>> >
>> > Some good tips there . . . I did two of them on a CR-V a while ago and
>> > there's no tension on the upper. The separator is available at places
>> > that carry the Whun-Hung-Low imported tools. In Canada Princess Auto
>> > has
>> > them for $20. Made in taiwan. It took about 45 minutes to swap out the
>> > upper arm and I was able to keep the old part (moved it to another
>> > CR-V)
>> > since the special tool doesn't wreck the boot.
>> >
>> > 'Curly'
>>
>> I've bought and used the 20.00 Princess auto ball joint popper.
>> Makes me wonder why I didn't buy one of these decades ago!
>
> ------------------------------------
> Because they've always been about $60CAN ???
>
> ++++++++++++++++++++++++++
Yeah, that /was/ probably why...
> I was there tonight and they are on sale for $16.99. I paid $63 for the
> 'real ' one a year ago. Think it's DTC or something. The one shown in
> the Honda manual is much thinner so it really gets under the boot
> better. Maybe I'll buy myself the Princess Auto 'stocking stuffer'
> version and grind it down just like the one in the Honda manual. Way
> less stressful when you don't have to worry about chopping up the boot.
>
> 'Curly'
Tighten, pause,... tighten, pause...tighten, pause....tighten, pausPOP!
06-23-2006, 09:13 PM
#9
Guest
Posts: n/a
Re: Left Upper Control Arm Replacement
Well, this is not exactly timely, but yes, I just put one in my 90 Accord.
Using a Haynes manual, but I prefer a factory service manual. No, it wasn't
hard for me to do. The parts came from eBay. I removed the strut and then
replaced the control arm. Torquing the pivot bolts/nuts before installing
saved me a lot of hassle. I used the original control arm as a guide for
that. I just followed the steps and it was pretty straightforward. Now if
I could just figure out how to get the steering tie rod end off...
dw
"Face" <face@yahoo.com> wrote in message
news:face-553982.07342917122005@news-rdr-03.ohiordc.rr.com...
> The ball joint on the upper left control arm on my 92 Accord is bad and
> needs to be replaced, the control arm that is. I'm considering doing
> this myself. Has anyone one out there ever replaced on? Any comments on
> how hard it is to do?
>
> Thanks
Using a Haynes manual, but I prefer a factory service manual. No, it wasn't
hard for me to do. The parts came from eBay. I removed the strut and then
replaced the control arm. Torquing the pivot bolts/nuts before installing
saved me a lot of hassle. I used the original control arm as a guide for
that. I just followed the steps and it was pretty straightforward. Now if
I could just figure out how to get the steering tie rod end off...
dw
"Face" <face@yahoo.com> wrote in message
news:face-553982.07342917122005@news-rdr-03.ohiordc.rr.com...
> The ball joint on the upper left control arm on my 92 Accord is bad and
> needs to be replaced, the control arm that is. I'm considering doing
> this myself. Has anyone one out there ever replaced on? Any comments on
> how hard it is to do?
>
> Thanks
06-23-2006, 09:13 PM
#10
Guest
Posts: n/a
Re: Left Upper Control Arm Replacement
Well, this is not exactly timely, but yes, I just put one in my 90 Accord.
Using a Haynes manual, but I prefer a factory service manual. No, it wasn't
hard for me to do. The parts came from eBay. I removed the strut and then
replaced the control arm. Torquing the pivot bolts/nuts before installing
saved me a lot of hassle. I used the original control arm as a guide for
that. I just followed the steps and it was pretty straightforward. Now if
I could just figure out how to get the steering tie rod end off...
dw
"Face" <face@yahoo.com> wrote in message
news:face-553982.07342917122005@news-rdr-03.ohiordc.rr.com...
> The ball joint on the upper left control arm on my 92 Accord is bad and
> needs to be replaced, the control arm that is. I'm considering doing
> this myself. Has anyone one out there ever replaced on? Any comments on
> how hard it is to do?
>
> Thanks
Using a Haynes manual, but I prefer a factory service manual. No, it wasn't
hard for me to do. The parts came from eBay. I removed the strut and then
replaced the control arm. Torquing the pivot bolts/nuts before installing
saved me a lot of hassle. I used the original control arm as a guide for
that. I just followed the steps and it was pretty straightforward. Now if
I could just figure out how to get the steering tie rod end off...
dw
"Face" <face@yahoo.com> wrote in message
news:face-553982.07342917122005@news-rdr-03.ohiordc.rr.com...
> The ball joint on the upper left control arm on my 92 Accord is bad and
> needs to be replaced, the control arm that is. I'm considering doing
> this myself. Has anyone one out there ever replaced on? Any comments on
> how hard it is to do?
>
> Thanks
06-23-2006, 09:13 PM
#11
Guest
Posts: n/a
Re: Left Upper Control Arm Replacement
Well, this is not exactly timely, but yes, I just put one in my 90 Accord.
Using a Haynes manual, but I prefer a factory service manual. No, it wasn't
hard for me to do. The parts came from eBay. I removed the strut and then
replaced the control arm. Torquing the pivot bolts/nuts before installing
saved me a lot of hassle. I used the original control arm as a guide for
that. I just followed the steps and it was pretty straightforward. Now if
I could just figure out how to get the steering tie rod end off...
dw
"Face" <face@yahoo.com> wrote in message
news:face-553982.07342917122005@news-rdr-03.ohiordc.rr.com...
> The ball joint on the upper left control arm on my 92 Accord is bad and
> needs to be replaced, the control arm that is. I'm considering doing
> this myself. Has anyone one out there ever replaced on? Any comments on
> how hard it is to do?
>
> Thanks
Using a Haynes manual, but I prefer a factory service manual. No, it wasn't
hard for me to do. The parts came from eBay. I removed the strut and then
replaced the control arm. Torquing the pivot bolts/nuts before installing
saved me a lot of hassle. I used the original control arm as a guide for
that. I just followed the steps and it was pretty straightforward. Now if
I could just figure out how to get the steering tie rod end off...
dw
"Face" <face@yahoo.com> wrote in message
news:face-553982.07342917122005@news-rdr-03.ohiordc.rr.com...
> The ball joint on the upper left control arm on my 92 Accord is bad and
> needs to be replaced, the control arm that is. I'm considering doing
> this myself. Has anyone one out there ever replaced on? Any comments on
> how hard it is to do?
>
> Thanks
Thread
Thread Starter
Forum
Replies
Last Post
cardstegra
Car Parts For Sale
0
05-02-2005 02:55 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
