Elantra 1992 caliper reassembly
08-12-2006, 08:25 PM
#1
Guest
Posts: n/a
Elantra 1992 caliper reassembly
Can Kleen-flo EXE-SLIDE brake lubricant be used on the piston, the
piston seal and, the piston boot before reassembly?
I had difficulty removing the piston boot from the caliper.. I
suspect reassembly is much more difficult. Is there a trick to
facilitate the operation: inserting the lip of the piston boot in the
caliper groove?
Thank you very much for your help.
--
Jean Castonguay
lectrocommande Pascal
piston seal and, the piston boot before reassembly?
I had difficulty removing the piston boot from the caliper.. I
suspect reassembly is much more difficult. Is there a trick to
facilitate the operation: inserting the lip of the piston boot in the
caliper groove?
Thank you very much for your help.
--
Jean Castonguay
lectrocommande Pascal
08-14-2006, 07:29 PM
#2
Guest
Posts: n/a
Re: Elantra 1992 caliper reassembly
The easiest way I've found to install a caliper piston boot is as follows:
1. Put the boot onto the *back* of the piston so that the edge to be
inserted into the caliper groove hangs off the piston. The boot should be
pretty well stretched out at this point.
2. Gradually maneuver the piston to insert the boot into the groove in
the caliper. Use a small screwdriver or similar tool to *gently* push the
final half or so of the boot into position in the caliper groove.
3. Once the boot is in place in the caliper, gradually slide the piston
back into the boot until the boot engages the groove in the piston.
I know this sounds pretty simple, but it's still tedious work. I usually
need to try two or three times to get everything just right. If you're in
doubt, back up a little and make sure everything is just so. Don't force
anything. Everything should go smoothly when aligned and fitted properly.
1. Put the boot onto the *back* of the piston so that the edge to be
inserted into the caliper groove hangs off the piston. The boot should be
pretty well stretched out at this point.
2. Gradually maneuver the piston to insert the boot into the groove in
the caliper. Use a small screwdriver or similar tool to *gently* push the
final half or so of the boot into position in the caliper groove.
3. Once the boot is in place in the caliper, gradually slide the piston
back into the boot until the boot engages the groove in the piston.
I know this sounds pretty simple, but it's still tedious work. I usually
need to try two or three times to get everything just right. If you're in
doubt, back up a little and make sure everything is just so. Don't force
anything. Everything should go smoothly when aligned and fitted properly.
08-14-2006, 07:29 PM
#3
Guest
Posts: n/a
Re: Elantra 1992 caliper reassembly
The easiest way I've found to install a caliper piston boot is as follows:
1. Put the boot onto the *back* of the piston so that the edge to be
inserted into the caliper groove hangs off the piston. The boot should be
pretty well stretched out at this point.
2. Gradually maneuver the piston to insert the boot into the groove in
the caliper. Use a small screwdriver or similar tool to *gently* push the
final half or so of the boot into position in the caliper groove.
3. Once the boot is in place in the caliper, gradually slide the piston
back into the boot until the boot engages the groove in the piston.
I know this sounds pretty simple, but it's still tedious work. I usually
need to try two or three times to get everything just right. If you're in
doubt, back up a little and make sure everything is just so. Don't force
anything. Everything should go smoothly when aligned and fitted properly.
1. Put the boot onto the *back* of the piston so that the edge to be
inserted into the caliper groove hangs off the piston. The boot should be
pretty well stretched out at this point.
2. Gradually maneuver the piston to insert the boot into the groove in
the caliper. Use a small screwdriver or similar tool to *gently* push the
final half or so of the boot into position in the caliper groove.
3. Once the boot is in place in the caliper, gradually slide the piston
back into the boot until the boot engages the groove in the piston.
I know this sounds pretty simple, but it's still tedious work. I usually
need to try two or three times to get everything just right. If you're in
doubt, back up a little and make sure everything is just so. Don't force
anything. Everything should go smoothly when aligned and fitted properly.
08-16-2006, 11:40 AM
#4
Guest
Posts: n/a
Re: Elantra 1992 caliper reassembly
On Mon, 14 Aug 2006 23:29:16 UTC, "hyundaitech"
<notpublic@not.public.com> wrote:
> The easiest way I've found to install a caliper piston boot is as follows:
>
Thank you very much. You gave me the tip I needed.
I will heed your suggestion to try several times. I have not yet
thrown the rubber parts...
--
Jean Castonguay
lectrocommande Pascal
<notpublic@not.public.com> wrote:
> The easiest way I've found to install a caliper piston boot is as follows:
>
Thank you very much. You gave me the tip I needed.
I will heed your suggestion to try several times. I have not yet
thrown the rubber parts...
--
Jean Castonguay
lectrocommande Pascal
08-16-2006, 11:40 AM
#5
Guest
Posts: n/a
Re: Elantra 1992 caliper reassembly
On Mon, 14 Aug 2006 23:29:16 UTC, "hyundaitech"
<notpublic@not.public.com> wrote:
> The easiest way I've found to install a caliper piston boot is as follows:
>
Thank you very much. You gave me the tip I needed.
I will heed your suggestion to try several times. I have not yet
thrown the rubber parts...
--
Jean Castonguay
lectrocommande Pascal
<notpublic@not.public.com> wrote:
> The easiest way I've found to install a caliper piston boot is as follows:
>
Thank you very much. You gave me the tip I needed.
I will heed your suggestion to try several times. I have not yet
thrown the rubber parts...
--
Jean Castonguay
lectrocommande Pascal
Thread
Thread Starter
Forum
Replies
Last Post
ericvallejo5000@hotmail.com
Hyundai Mailing List
4
07-24-2007 12:26 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)