mk.kemkd@yahoo.com

I have hyundai accent 1.5 model 2000

127000 mile

I was had fault code p0422 and when try to remove (oxygen sensor)
can't remove it I cut the electrical wire to remove it but I can't

after that I have (p0135)

I get (DW40) and I remove (oxygen sensor) and replace it by new one
and remove the battery the (check lamp) was closed

after 40 miles (check lamp ) opened
and have this code (P1123) I was change all Spark plugs NGK, and Spark
Plug Wires , and remove battery

after some miles (check lamp) opened

I remove (maf) and cleaned it and return it

what can I do again for resolve this fault code

hyundaitech

P0422 indicates a problem with catalyst inefficiency. You probably need a
new catalytic converter. This code will eventually return.

P1123 indicates a rich condition. Considering this occurred immediately
after replacing the oxygen sensor, I'd suspect the oxygen sensor you
installed is defective or isn't compatible with the vehicle. I'd
recommend using a factory oxygen sensor.

--
Message posted using http://www.talkaboutautos.com/group/alt.autos.hyundai/
More information at http://www.talkaboutautos.com/faq.html

mk.kemkd@yahoo.com

On Jun 12, 7:28 pm, "hyundaitech" <notpub...@not.public.com> wrote:
> P0422 indicates a problem with catalyst inefficiency. You probably need a
> new catalytic converter. This code will eventually return.
>
> P1123 indicates a rich condition. Considering this occurred immediately
> after replacing the oxygen sensor, I'd suspect the oxygen sensor you
> installed is defective or isn't compatible with the vehicle. I'd
> recommend using a factory oxygen sensor.
>
> --
> Message posted usinghttp://www.talkaboutautos.com/group/alt.autos.hyundai/
> More information athttp://www.talkaboutautos.com/faq.html


the oxygen sensor is (factory oxygen sensor) same a old one.
and the technician off (scan tool) tell me, the oxygen sensor work
good coze he read this in his scan tool.

and this code P1123 was found after 4 day from change (oxygen sensor)



and need to ask some thing
I have program for scan can I see the problem code, by cable between
my computer and car without interface or if u have scheme for easy
interface i hope to send to me for scan my fault code with my self

thank you

like this photo

prisediag7.jpg picture by kemks

http://s211.photobucket.com/albums/b...prisediag7.jpg

hyundaitech

When it comes down to it, there are many things that can cause P1123, but
there's a reason I think the problem is with the replacement oxygen
sensor. Here's my logic:

1. P0422 will not set unless the ECM thinks the oxygen sensors are
working correctly. This is because the ECM uses data from the oxygen
sensors to determine catalyst efficiency. Hence, it's reasonably to
assume the oxygen sensor was working properly prior to replacement.

2. P1123 did not set until after the oxygen sensor was replaced. Since
nothing had been done between the original P0422 and the subsequent P1123,
it's reasonable to assume there's some problem with the new oxygen sensor.
If it is indeed a factory part (purchased at Hyundai dealer), then it's
possible it's defective (not likely) or was damaged on installation.

Other things that can cause P1123:
-- stuck open purge control valve
-- excessive fuel pressure
-- air intake restriction
-- defective air flow sensor.

I don't currently have access to the photobucket site, so I cannot see the
picture, but I don't have experience with any of the generic scan tools for
home use. About the only thing I can do is refer you to your owner's
manual for the product.


Also, if you can tell me what the mechanic saw that led him to believe the
new oxygen sensor was functioning properly, that may assist me.

--
Message posted using http://www.talkaboutautos.com/group/alt.autos.hyundai/
More information at http://www.talkaboutautos.com/faq.html

Matthew Fedder

On Jun 12, 9:28 am, "hyundaitech" <notpub...@not.public.com> wrote:
> P0422 indicates a problem with catalyst inefficiency. You probably needa
> new catalytic converter. This code will eventually return.

I started getting P0422's less than a month after I passed a smog
check, so I'm assuming the downstream O2 sensor is bad (the upstream
one went bad last year). Is that a reasonable assumption?

hyundaitech

Nope. You probably need a new converter. You should, of course, verify
the oxygen sensors are properly connected (upstream to upstream connector
and downstream to downstream connector) and are displaying normal pattern
(other than a large amplitude from the rear sensor). But ultimately, at a
probability of 95% or better, the converter isn't working so well.

--
Message posted using http://www.talkaboutautos.com/group/alt.autos.hyundai/
More information at http://www.talkaboutautos.com/faq.html

mk.kemkd@yahoo.com

> Also, if you can tell me what the mechanic saw that led him to believe the
> new oxygen sensor was functioning properly, that may assist me.
>

the mechanic was tell me he test it my scan tool for measure it and he
must between (0:1) if it that O2S will be good and this also in the
autodata program ((O2 level at idle speed -------- Vol. % O2
0,1-0,5 )
and i was went to hem to assure this rate is my o2 rate and he was
tell me your O2 is good.

and I was went to hem to assure this rate is my o2 rate and he was
tell me your O2 is good and he have this volume rate.

the mechanic tell me may be (MAF) must replace it
but this is so expensive to me, and I afraid when I change it this
code return back

* my fuel consumption is so high.
* I was clean this MAF by (CRC).

hyundaitech

O2 voltages between 0 and 1 are normal, but they don't necessarily imply
the sensor is functioning properly. The ECM has the capability of
adapting to skewed readings from a faulty or improper sensor, causing the
voltage readings you describe.

I'd also be interested in your short term and long term fuel trim values,
both in the current data stream and in the freeze frame data.

It's possible you damaged the MAF by attempting to clean it, but since the
same code was present before and after the cleaning, that's not likely. I,
too, doubt the MAF will solve your problem, but I don't have the car in
front of me to diagnose, either.

--
Message posted using http://www.talkaboutautos.com/group/alt.autos.hyundai/
More information at http://www.talkaboutautos.com/faq.html

mk.kemkd@yahoo.com

thanks for your attention, but if you can tell me some thing to assure
if my O2S work good or not work or MAF work or not work

coze until now I spend more money for resolved this problem

and the new O2S was had same code from the old one , and this O2S was
closed in the factory case and I think the factory made quality test
before sell it , this make me suspicion of my O2S is defective if you
have procedure for calibration it, please tell me how that.

and when I replaced it with the new , try to be punctual and careful
to not transact hard

and thanks for your cooperation

hyundaitech

"had same code"

What is this code? I'm not sure you understand what I mean by "factory."
Factory means a part obtained through the vehicle manufacturer's (Hyundai
in this case) distribution network (in the U.S., that would be a Hyundai
dealer) and in the vehicle manufacturer's packaging.


For checking the air flow sensor, you'll be interested in technical
service bulletin 01-36-022. You can view it at www.hmaservice.com--
you'll need to register for an account if you don't have one. It gives
specifications for normal air flow readings. This TSB was intended for
diagnosing a P1128 code, so instead of MAF readings that are too low,
you'll be looking for MAF readings that may be too high.

Unfortunately, there's little good way to test an oxygen sensor in the
field. Checking for normal fluctuation between 0 and 1 Volt (a certain
number of high and low switches in a certain period of time) is the best a
mechanic can typically do. But as I said previously, meeting these
criteria doesn't mean the sensor is good. Beyond that, the only other
option we'd have without some sort of sensor-testing apparatus would be to
replace the sensor with one known to work properly.

--
Message posted using http://www.talkaboutautos.com/group/alt.autos.hyundai/
More information at http://www.talkaboutautos.com/faq.html

mk.kemkd@yahoo.com

thanks for your replay i will tray to test another O2 one

mk.kemkd@yahoo.com

I was found the flex pipe is broken, are this reason for this fault
code?

hyundaitech

Could be. Start by fixing the pipe. Too much fresh air in the exhaust can
confuse the oxygen sensors.

--
Message posted using http://www.talkaboutautos.com/group/alt.autos.hyundai/
More information at http://www.talkaboutautos.com/faq.html

mk.kemkd@yahoo.com

first I try to scan the fault code with another mechanic.
the first mechanic found P1123 but another one, he found in the (X431
scan tool)

P0422

I was replaced flex pipe and ensure no have any leaking

and don't clear the fault code when I drive by my car after many
miles, I found my (check lamp) is close with it self

but when refill fuel (92) I found the check lamp return open