My car's too low for a jack!
Thread Starter
Skilled GTcars Poster
Joined: Oct 2005
Posts: 971
From: I'm in the Avatar....(Duh)
Rep Power: 772 
My car's too low for a jack!
I love how low my car sits......but now I can't get a jack under it! I figured if I bought one of those low-profile jacks I'd be ok and it would slide under far enough to get it up in the air......WRONG!!!!
Well, at least I have a really nice jack and jack stands for when I do get it under there.(last picture) They had 'em on sale at GI JOES for $119.00 marked down from $139.00, another place wanted $149.00 for the exact same set. When I got to the register though, they rang up at $99.00, I said Sweet!
Now the only way I can get the jack under there, is to use these staggered ramps I just built tonight. I still need to staple some roofing shingles to the surface for better traction, but at least now I'll be able to get the car up high enough to push the jack under it.
As you can see from the pictures, they barely fit under the car......but they do fit. I need to get another couple pieces of board though and nail 'em to the end of the ramp so it sticks up about an inch as a stopper, just to be safe.
Well, at least I have a really nice jack and jack stands for when I do get it under there.(last picture) They had 'em on sale at GI JOES for $119.00 marked down from $139.00, another place wanted $149.00 for the exact same set. When I got to the register though, they rang up at $99.00, I said Sweet!
Now the only way I can get the jack under there, is to use these staggered ramps I just built tonight. I still need to staple some roofing shingles to the surface for better traction, but at least now I'll be able to get the car up high enough to push the jack under it.
As you can see from the pictures, they barely fit under the car......but they do fit. I need to get another couple pieces of board though and nail 'em to the end of the ramp so it sticks up about an inch as a stopper, just to be safe.
~~~ SITE SPONSOR ~~~
Joined: Oct 2005
Posts: 2,083
From: tucson, az
Rep Power: 794
lol i used to have the same problem on my last car i would just use a stock siscor jack to start then put a stand under then switch to a good jack lol it sucked, but i am pretty sure ur car is lower but those ramps are a really good idea too bad i couldnt think of something like that
Thread Starter
Skilled GTcars Poster
Joined: Oct 2005
Posts: 971
From: I'm in the Avatar....(Duh)
Rep Power: 772
Well, I tested them out today cause I had to swap out the clear corners.......worked awesome! I was thinking they might move as I drove up on them, but they stayed right in place. I was a little nervous though about going too far and driving off the end. I really need to nail a few extra pieces on the end for a stopper, but all in all they worked great, and it only cost me $13.00 and about 15 minutes worth of time.
GTcars - Post God !
Joined: Oct 2004
Posts: 6,626
From: palatine,il (chicago)
Rep Power: 922
lmao Tony. my dad usually lifts up on the fender while i position the jack. then i get it up to the lowest setting for the drivers side jack, drop it down, then go in the middle on the k member.
GTcars - Post God !
Joined: Nov 2003
Posts: 7,173
From: Valencia, CA
Rep Power: 967
i have these wheel ramps from either ecklers or mid america. they have a 245 max tire...which works great for me. but they have a couple adapter deals or whatever that you lay out in front and they make the incline a lot longer and shallower so it works great. its how i pulled my trans..8 inches off the ground 
lol.
lol.
