1988 Honda Accord Lxi rev'ing Up and Down
12-02-2003, 01:01 AM
#1
Guest
Posts: n/a
1988 Honda Accord Lxi rev'ing Up and Down
Got a question maybe someone can answer...
My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and down
after warming up. I thought maybe the vacuum adv. on the distributor
might be bad, but verifing timing (pulling hoses and blocking/ chk
timing) all are alright (car does not rev up and dwn when I do this).
But once I put the hoses back same thing. If I pull the hose closest to
the front end of the car, the engine stops rev'ing up and dwn. Another
thing I did is replacing the all hoses to vacuum adv, I disconnected the
power plug to the vacuum control module (left portion of firewall) and the
car stops rev'ing up and down. SUGGESTIONS????
My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and down
after warming up. I thought maybe the vacuum adv. on the distributor
might be bad, but verifing timing (pulling hoses and blocking/ chk
timing) all are alright (car does not rev up and dwn when I do this).
But once I put the hoses back same thing. If I pull the hose closest to
the front end of the car, the engine stops rev'ing up and dwn. Another
thing I did is replacing the all hoses to vacuum adv, I disconnected the
power plug to the vacuum control module (left portion of firewall) and the
car stops rev'ing up and down. SUGGESTIONS????
12-03-2003, 03:13 AM
#2
Guest
Posts: n/a
Re: 1988 Honda Accord Lxi rev'ing Up and Down
Best I can think of: turn the heat to max and bleed coolant. Remove the
battery for a minute to reset ECU.
> My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and down
> after warming up. I thought maybe the vacuum adv. on the distributor
> might be bad, but verifing timing (pulling hoses and blocking/ chk
> timing) all are alright (car does not rev up and dwn when I do this).
> But once I put the hoses back same thing. If I pull the hose closest to
> the front end of the car, the engine stops rev'ing up and dwn. Another
> thing I did is replacing the all hoses to vacuum adv, I disconnected the
> power plug to the vacuum control module (left portion of firewall) and the
> car stops rev'ing up and down. SUGGESTIONS????
battery for a minute to reset ECU.
> My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and down
> after warming up. I thought maybe the vacuum adv. on the distributor
> might be bad, but verifing timing (pulling hoses and blocking/ chk
> timing) all are alright (car does not rev up and dwn when I do this).
> But once I put the hoses back same thing. If I pull the hose closest to
> the front end of the car, the engine stops rev'ing up and dwn. Another
> thing I did is replacing the all hoses to vacuum adv, I disconnected the
> power plug to the vacuum control module (left portion of firewall) and the
> car stops rev'ing up and down. SUGGESTIONS????
12-03-2003, 03:13 AM
#3
Guest
Posts: n/a
Re: 1988 Honda Accord Lxi rev'ing Up and Down
Best I can think of: turn the heat to max and bleed coolant. Remove the
battery for a minute to reset ECU.
> My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and down
> after warming up. I thought maybe the vacuum adv. on the distributor
> might be bad, but verifing timing (pulling hoses and blocking/ chk
> timing) all are alright (car does not rev up and dwn when I do this).
> But once I put the hoses back same thing. If I pull the hose closest to
> the front end of the car, the engine stops rev'ing up and dwn. Another
> thing I did is replacing the all hoses to vacuum adv, I disconnected the
> power plug to the vacuum control module (left portion of firewall) and the
> car stops rev'ing up and down. SUGGESTIONS????
battery for a minute to reset ECU.
> My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and down
> after warming up. I thought maybe the vacuum adv. on the distributor
> might be bad, but verifing timing (pulling hoses and blocking/ chk
> timing) all are alright (car does not rev up and dwn when I do this).
> But once I put the hoses back same thing. If I pull the hose closest to
> the front end of the car, the engine stops rev'ing up and dwn. Another
> thing I did is replacing the all hoses to vacuum adv, I disconnected the
> power plug to the vacuum control module (left portion of firewall) and the
> car stops rev'ing up and down. SUGGESTIONS????
12-03-2003, 03:13 AM
#4
Guest
Posts: n/a
Re: 1988 Honda Accord Lxi rev'ing Up and Down
Best I can think of: turn the heat to max and bleed coolant. Remove the
battery for a minute to reset ECU.
> My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and down
> after warming up. I thought maybe the vacuum adv. on the distributor
> might be bad, but verifing timing (pulling hoses and blocking/ chk
> timing) all are alright (car does not rev up and dwn when I do this).
> But once I put the hoses back same thing. If I pull the hose closest to
> the front end of the car, the engine stops rev'ing up and dwn. Another
> thing I did is replacing the all hoses to vacuum adv, I disconnected the
> power plug to the vacuum control module (left portion of firewall) and the
> car stops rev'ing up and down. SUGGESTIONS????
battery for a minute to reset ECU.
> My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and down
> after warming up. I thought maybe the vacuum adv. on the distributor
> might be bad, but verifing timing (pulling hoses and blocking/ chk
> timing) all are alright (car does not rev up and dwn when I do this).
> But once I put the hoses back same thing. If I pull the hose closest to
> the front end of the car, the engine stops rev'ing up and dwn. Another
> thing I did is replacing the all hoses to vacuum adv, I disconnected the
> power plug to the vacuum control module (left portion of firewall) and the
> car stops rev'ing up and down. SUGGESTIONS????
12-03-2003, 03:13 AM
#5
Guest
Posts: n/a
Re: 1988 Honda Accord Lxi rev'ing Up and Down
Best I can think of: turn the heat to max and bleed coolant. Remove the
battery for a minute to reset ECU.
> My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and down
> after warming up. I thought maybe the vacuum adv. on the distributor
> might be bad, but verifing timing (pulling hoses and blocking/ chk
> timing) all are alright (car does not rev up and dwn when I do this).
> But once I put the hoses back same thing. If I pull the hose closest to
> the front end of the car, the engine stops rev'ing up and dwn. Another
> thing I did is replacing the all hoses to vacuum adv, I disconnected the
> power plug to the vacuum control module (left portion of firewall) and the
> car stops rev'ing up and down. SUGGESTIONS????
battery for a minute to reset ECU.
> My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and down
> after warming up. I thought maybe the vacuum adv. on the distributor
> might be bad, but verifing timing (pulling hoses and blocking/ chk
> timing) all are alright (car does not rev up and dwn when I do this).
> But once I put the hoses back same thing. If I pull the hose closest to
> the front end of the car, the engine stops rev'ing up and dwn. Another
> thing I did is replacing the all hoses to vacuum adv, I disconnected the
> power plug to the vacuum control module (left portion of firewall) and the
> car stops rev'ing up and down. SUGGESTIONS????
12-03-2003, 08:29 AM
#6
Guest
Posts: n/a
Re: 1988 Honda Accord Lxi rev'ing Up and Down
ECU re-set is done by removing the ECU fuse for ten seconds. The fuse
is in the under hood fuse box.
See if there is something in the intake screen for the vacuum source in
the big box full of controls on the passenger side of the outer
firewall. (all the vac lines run to it)
Good Luck! bob
Indian Summer wrote:
>
> Best I can think of: turn the heat to max and bleed coolant. Remove the
> battery for a minute to reset ECU.
>
> > My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and down
> > after warming up. I thought maybe the vacuum adv. on the distributor
> > might be bad, but verifing timing (pulling hoses and blocking/ chk
> > timing) all are alright (car does not rev up and dwn when I do this).
> > But once I put the hoses back same thing. If I pull the hose closest to
> > the front end of the car, the engine stops rev'ing up and dwn. Another
> > thing I did is replacing the all hoses to vacuum adv, I disconnected the
> > power plug to the vacuum control module (left portion of firewall) and the
> > car stops rev'ing up and down. SUGGESTIONS????
is in the under hood fuse box.
See if there is something in the intake screen for the vacuum source in
the big box full of controls on the passenger side of the outer
firewall. (all the vac lines run to it)
Good Luck! bob
Indian Summer wrote:
>
> Best I can think of: turn the heat to max and bleed coolant. Remove the
> battery for a minute to reset ECU.
>
> > My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and down
> > after warming up. I thought maybe the vacuum adv. on the distributor
> > might be bad, but verifing timing (pulling hoses and blocking/ chk
> > timing) all are alright (car does not rev up and dwn when I do this).
> > But once I put the hoses back same thing. If I pull the hose closest to
> > the front end of the car, the engine stops rev'ing up and dwn. Another
> > thing I did is replacing the all hoses to vacuum adv, I disconnected the
> > power plug to the vacuum control module (left portion of firewall) and the
> > car stops rev'ing up and down. SUGGESTIONS????
12-03-2003, 08:29 AM
#7
Guest
Posts: n/a
Re: 1988 Honda Accord Lxi rev'ing Up and Down
ECU re-set is done by removing the ECU fuse for ten seconds. The fuse
is in the under hood fuse box.
See if there is something in the intake screen for the vacuum source in
the big box full of controls on the passenger side of the outer
firewall. (all the vac lines run to it)
Good Luck! bob
Indian Summer wrote:
>
> Best I can think of: turn the heat to max and bleed coolant. Remove the
> battery for a minute to reset ECU.
>
> > My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and down
> > after warming up. I thought maybe the vacuum adv. on the distributor
> > might be bad, but verifing timing (pulling hoses and blocking/ chk
> > timing) all are alright (car does not rev up and dwn when I do this).
> > But once I put the hoses back same thing. If I pull the hose closest to
> > the front end of the car, the engine stops rev'ing up and dwn. Another
> > thing I did is replacing the all hoses to vacuum adv, I disconnected the
> > power plug to the vacuum control module (left portion of firewall) and the
> > car stops rev'ing up and down. SUGGESTIONS????
is in the under hood fuse box.
See if there is something in the intake screen for the vacuum source in
the big box full of controls on the passenger side of the outer
firewall. (all the vac lines run to it)
Good Luck! bob
Indian Summer wrote:
>
> Best I can think of: turn the heat to max and bleed coolant. Remove the
> battery for a minute to reset ECU.
>
> > My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and down
> > after warming up. I thought maybe the vacuum adv. on the distributor
> > might be bad, but verifing timing (pulling hoses and blocking/ chk
> > timing) all are alright (car does not rev up and dwn when I do this).
> > But once I put the hoses back same thing. If I pull the hose closest to
> > the front end of the car, the engine stops rev'ing up and dwn. Another
> > thing I did is replacing the all hoses to vacuum adv, I disconnected the
> > power plug to the vacuum control module (left portion of firewall) and the
> > car stops rev'ing up and down. SUGGESTIONS????
12-03-2003, 08:29 AM
#8
Guest
Posts: n/a
Re: 1988 Honda Accord Lxi rev'ing Up and Down
ECU re-set is done by removing the ECU fuse for ten seconds. The fuse
is in the under hood fuse box.
See if there is something in the intake screen for the vacuum source in
the big box full of controls on the passenger side of the outer
firewall. (all the vac lines run to it)
Good Luck! bob
Indian Summer wrote:
>
> Best I can think of: turn the heat to max and bleed coolant. Remove the
> battery for a minute to reset ECU.
>
> > My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and down
> > after warming up. I thought maybe the vacuum adv. on the distributor
> > might be bad, but verifing timing (pulling hoses and blocking/ chk
> > timing) all are alright (car does not rev up and dwn when I do this).
> > But once I put the hoses back same thing. If I pull the hose closest to
> > the front end of the car, the engine stops rev'ing up and dwn. Another
> > thing I did is replacing the all hoses to vacuum adv, I disconnected the
> > power plug to the vacuum control module (left portion of firewall) and the
> > car stops rev'ing up and down. SUGGESTIONS????
is in the under hood fuse box.
See if there is something in the intake screen for the vacuum source in
the big box full of controls on the passenger side of the outer
firewall. (all the vac lines run to it)
Good Luck! bob
Indian Summer wrote:
>
> Best I can think of: turn the heat to max and bleed coolant. Remove the
> battery for a minute to reset ECU.
>
> > My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and down
> > after warming up. I thought maybe the vacuum adv. on the distributor
> > might be bad, but verifing timing (pulling hoses and blocking/ chk
> > timing) all are alright (car does not rev up and dwn when I do this).
> > But once I put the hoses back same thing. If I pull the hose closest to
> > the front end of the car, the engine stops rev'ing up and dwn. Another
> > thing I did is replacing the all hoses to vacuum adv, I disconnected the
> > power plug to the vacuum control module (left portion of firewall) and the
> > car stops rev'ing up and down. SUGGESTIONS????
12-03-2003, 08:29 AM
#9
Guest
Posts: n/a
Re: 1988 Honda Accord Lxi rev'ing Up and Down
ECU re-set is done by removing the ECU fuse for ten seconds. The fuse
is in the under hood fuse box.
See if there is something in the intake screen for the vacuum source in
the big box full of controls on the passenger side of the outer
firewall. (all the vac lines run to it)
Good Luck! bob
Indian Summer wrote:
>
> Best I can think of: turn the heat to max and bleed coolant. Remove the
> battery for a minute to reset ECU.
>
> > My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and down
> > after warming up. I thought maybe the vacuum adv. on the distributor
> > might be bad, but verifing timing (pulling hoses and blocking/ chk
> > timing) all are alright (car does not rev up and dwn when I do this).
> > But once I put the hoses back same thing. If I pull the hose closest to
> > the front end of the car, the engine stops rev'ing up and dwn. Another
> > thing I did is replacing the all hoses to vacuum adv, I disconnected the
> > power plug to the vacuum control module (left portion of firewall) and the
> > car stops rev'ing up and down. SUGGESTIONS????
is in the under hood fuse box.
See if there is something in the intake screen for the vacuum source in
the big box full of controls on the passenger side of the outer
firewall. (all the vac lines run to it)
Good Luck! bob
Indian Summer wrote:
>
> Best I can think of: turn the heat to max and bleed coolant. Remove the
> battery for a minute to reset ECU.
>
> > My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and down
> > after warming up. I thought maybe the vacuum adv. on the distributor
> > might be bad, but verifing timing (pulling hoses and blocking/ chk
> > timing) all are alright (car does not rev up and dwn when I do this).
> > But once I put the hoses back same thing. If I pull the hose closest to
> > the front end of the car, the engine stops rev'ing up and dwn. Another
> > thing I did is replacing the all hoses to vacuum adv, I disconnected the
> > power plug to the vacuum control module (left portion of firewall) and the
> > car stops rev'ing up and down. SUGGESTIONS????
12-03-2003, 09:35 AM
#10
Guest
Posts: n/a
Re: 1988 Honda Accord Lxi rev'ing Up and Down
Indian Summer wrote:
>
> Best I can think of: turn the heat to max and bleed coolant. Remove the
> battery for a minute to reset ECU.
>
> > My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and
> > down after warming up. I thought maybe the vacuum adv. on the
> > distributor might be bad, but verifing timing (pulling hoses and
> > blocking/ chk timing) all are alright (car does not rev up and dwn when
> > I do this). But once I put the hoses back same thing. If I pull the
> > hose closest to the front end of the car, the engine stops rev'ing up
> > and dwn. Another thing I did is replacing the all hoses to vacuum adv,
> > I disconnected the power plug to the vacuum control module (left
> > portion of firewall) and the car stops rev'ing up and down.
> > SUGGESTIONS????
I agree with the above suggestion to bleed the coolant. The most common
problem associated with the idle cycling up and down is usually due to a
lack of coolant flowing through the cold start valve. The valve is item
number 8 in this diagram http://tinyurl.com/xj18. If the valve doesn't warm
up as the engine warms up (from coolant flowing through the bottom part),
the PGMFI system will misinterpret the condition and idle cycling results.
The first thing to due is to check the valve and make sure that the lower
part of the valve gets hot as the engine warms up. If the valve doesn't get
hot, try bleeding the coolant and make sure that coolant is flowing through
the valve. You can double check the valve as a source of the cycling by
removing the two screws from the top along with the oval shaped plate and
push down on the inner valve/plunger in the center. The cycling should stop
if the valve is the problem. If the valve is getting hot and pushing the
inner plunger down stops the cycling, then the valve likely needs to be
replaced.
Eric
>
> Best I can think of: turn the heat to max and bleed coolant. Remove the
> battery for a minute to reset ECU.
>
> > My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and
> > down after warming up. I thought maybe the vacuum adv. on the
> > distributor might be bad, but verifing timing (pulling hoses and
> > blocking/ chk timing) all are alright (car does not rev up and dwn when
> > I do this). But once I put the hoses back same thing. If I pull the
> > hose closest to the front end of the car, the engine stops rev'ing up
> > and dwn. Another thing I did is replacing the all hoses to vacuum adv,
> > I disconnected the power plug to the vacuum control module (left
> > portion of firewall) and the car stops rev'ing up and down.
> > SUGGESTIONS????
I agree with the above suggestion to bleed the coolant. The most common
problem associated with the idle cycling up and down is usually due to a
lack of coolant flowing through the cold start valve. The valve is item
number 8 in this diagram http://tinyurl.com/xj18. If the valve doesn't warm
up as the engine warms up (from coolant flowing through the bottom part),
the PGMFI system will misinterpret the condition and idle cycling results.
The first thing to due is to check the valve and make sure that the lower
part of the valve gets hot as the engine warms up. If the valve doesn't get
hot, try bleeding the coolant and make sure that coolant is flowing through
the valve. You can double check the valve as a source of the cycling by
removing the two screws from the top along with the oval shaped plate and
push down on the inner valve/plunger in the center. The cycling should stop
if the valve is the problem. If the valve is getting hot and pushing the
inner plunger down stops the cycling, then the valve likely needs to be
replaced.
Eric
12-03-2003, 09:35 AM
#11
Guest
Posts: n/a
Re: 1988 Honda Accord Lxi rev'ing Up and Down
Indian Summer wrote:
>
> Best I can think of: turn the heat to max and bleed coolant. Remove the
> battery for a minute to reset ECU.
>
> > My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and
> > down after warming up. I thought maybe the vacuum adv. on the
> > distributor might be bad, but verifing timing (pulling hoses and
> > blocking/ chk timing) all are alright (car does not rev up and dwn when
> > I do this). But once I put the hoses back same thing. If I pull the
> > hose closest to the front end of the car, the engine stops rev'ing up
> > and dwn. Another thing I did is replacing the all hoses to vacuum adv,
> > I disconnected the power plug to the vacuum control module (left
> > portion of firewall) and the car stops rev'ing up and down.
> > SUGGESTIONS????
I agree with the above suggestion to bleed the coolant. The most common
problem associated with the idle cycling up and down is usually due to a
lack of coolant flowing through the cold start valve. The valve is item
number 8 in this diagram http://tinyurl.com/xj18. If the valve doesn't warm
up as the engine warms up (from coolant flowing through the bottom part),
the PGMFI system will misinterpret the condition and idle cycling results.
The first thing to due is to check the valve and make sure that the lower
part of the valve gets hot as the engine warms up. If the valve doesn't get
hot, try bleeding the coolant and make sure that coolant is flowing through
the valve. You can double check the valve as a source of the cycling by
removing the two screws from the top along with the oval shaped plate and
push down on the inner valve/plunger in the center. The cycling should stop
if the valve is the problem. If the valve is getting hot and pushing the
inner plunger down stops the cycling, then the valve likely needs to be
replaced.
Eric
>
> Best I can think of: turn the heat to max and bleed coolant. Remove the
> battery for a minute to reset ECU.
>
> > My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and
> > down after warming up. I thought maybe the vacuum adv. on the
> > distributor might be bad, but verifing timing (pulling hoses and
> > blocking/ chk timing) all are alright (car does not rev up and dwn when
> > I do this). But once I put the hoses back same thing. If I pull the
> > hose closest to the front end of the car, the engine stops rev'ing up
> > and dwn. Another thing I did is replacing the all hoses to vacuum adv,
> > I disconnected the power plug to the vacuum control module (left
> > portion of firewall) and the car stops rev'ing up and down.
> > SUGGESTIONS????
I agree with the above suggestion to bleed the coolant. The most common
problem associated with the idle cycling up and down is usually due to a
lack of coolant flowing through the cold start valve. The valve is item
number 8 in this diagram http://tinyurl.com/xj18. If the valve doesn't warm
up as the engine warms up (from coolant flowing through the bottom part),
the PGMFI system will misinterpret the condition and idle cycling results.
The first thing to due is to check the valve and make sure that the lower
part of the valve gets hot as the engine warms up. If the valve doesn't get
hot, try bleeding the coolant and make sure that coolant is flowing through
the valve. You can double check the valve as a source of the cycling by
removing the two screws from the top along with the oval shaped plate and
push down on the inner valve/plunger in the center. The cycling should stop
if the valve is the problem. If the valve is getting hot and pushing the
inner plunger down stops the cycling, then the valve likely needs to be
replaced.
Eric
12-03-2003, 09:35 AM
#12
Guest
Posts: n/a
Re: 1988 Honda Accord Lxi rev'ing Up and Down
Indian Summer wrote:
>
> Best I can think of: turn the heat to max and bleed coolant. Remove the
> battery for a minute to reset ECU.
>
> > My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and
> > down after warming up. I thought maybe the vacuum adv. on the
> > distributor might be bad, but verifing timing (pulling hoses and
> > blocking/ chk timing) all are alright (car does not rev up and dwn when
> > I do this). But once I put the hoses back same thing. If I pull the
> > hose closest to the front end of the car, the engine stops rev'ing up
> > and dwn. Another thing I did is replacing the all hoses to vacuum adv,
> > I disconnected the power plug to the vacuum control module (left
> > portion of firewall) and the car stops rev'ing up and down.
> > SUGGESTIONS????
I agree with the above suggestion to bleed the coolant. The most common
problem associated with the idle cycling up and down is usually due to a
lack of coolant flowing through the cold start valve. The valve is item
number 8 in this diagram http://tinyurl.com/xj18. If the valve doesn't warm
up as the engine warms up (from coolant flowing through the bottom part),
the PGMFI system will misinterpret the condition and idle cycling results.
The first thing to due is to check the valve and make sure that the lower
part of the valve gets hot as the engine warms up. If the valve doesn't get
hot, try bleeding the coolant and make sure that coolant is flowing through
the valve. You can double check the valve as a source of the cycling by
removing the two screws from the top along with the oval shaped plate and
push down on the inner valve/plunger in the center. The cycling should stop
if the valve is the problem. If the valve is getting hot and pushing the
inner plunger down stops the cycling, then the valve likely needs to be
replaced.
Eric
>
> Best I can think of: turn the heat to max and bleed coolant. Remove the
> battery for a minute to reset ECU.
>
> > My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and
> > down after warming up. I thought maybe the vacuum adv. on the
> > distributor might be bad, but verifing timing (pulling hoses and
> > blocking/ chk timing) all are alright (car does not rev up and dwn when
> > I do this). But once I put the hoses back same thing. If I pull the
> > hose closest to the front end of the car, the engine stops rev'ing up
> > and dwn. Another thing I did is replacing the all hoses to vacuum adv,
> > I disconnected the power plug to the vacuum control module (left
> > portion of firewall) and the car stops rev'ing up and down.
> > SUGGESTIONS????
I agree with the above suggestion to bleed the coolant. The most common
problem associated with the idle cycling up and down is usually due to a
lack of coolant flowing through the cold start valve. The valve is item
number 8 in this diagram http://tinyurl.com/xj18. If the valve doesn't warm
up as the engine warms up (from coolant flowing through the bottom part),
the PGMFI system will misinterpret the condition and idle cycling results.
The first thing to due is to check the valve and make sure that the lower
part of the valve gets hot as the engine warms up. If the valve doesn't get
hot, try bleeding the coolant and make sure that coolant is flowing through
the valve. You can double check the valve as a source of the cycling by
removing the two screws from the top along with the oval shaped plate and
push down on the inner valve/plunger in the center. The cycling should stop
if the valve is the problem. If the valve is getting hot and pushing the
inner plunger down stops the cycling, then the valve likely needs to be
replaced.
Eric
12-03-2003, 09:35 AM
#13
Guest
Posts: n/a
Re: 1988 Honda Accord Lxi rev'ing Up and Down
Indian Summer wrote:
>
> Best I can think of: turn the heat to max and bleed coolant. Remove the
> battery for a minute to reset ECU.
>
> > My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and
> > down after warming up. I thought maybe the vacuum adv. on the
> > distributor might be bad, but verifing timing (pulling hoses and
> > blocking/ chk timing) all are alright (car does not rev up and dwn when
> > I do this). But once I put the hoses back same thing. If I pull the
> > hose closest to the front end of the car, the engine stops rev'ing up
> > and dwn. Another thing I did is replacing the all hoses to vacuum adv,
> > I disconnected the power plug to the vacuum control module (left
> > portion of firewall) and the car stops rev'ing up and down.
> > SUGGESTIONS????
I agree with the above suggestion to bleed the coolant. The most common
problem associated with the idle cycling up and down is usually due to a
lack of coolant flowing through the cold start valve. The valve is item
number 8 in this diagram http://tinyurl.com/xj18. If the valve doesn't warm
up as the engine warms up (from coolant flowing through the bottom part),
the PGMFI system will misinterpret the condition and idle cycling results.
The first thing to due is to check the valve and make sure that the lower
part of the valve gets hot as the engine warms up. If the valve doesn't get
hot, try bleeding the coolant and make sure that coolant is flowing through
the valve. You can double check the valve as a source of the cycling by
removing the two screws from the top along with the oval shaped plate and
push down on the inner valve/plunger in the center. The cycling should stop
if the valve is the problem. If the valve is getting hot and pushing the
inner plunger down stops the cycling, then the valve likely needs to be
replaced.
Eric
>
> Best I can think of: turn the heat to max and bleed coolant. Remove the
> battery for a minute to reset ECU.
>
> > My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and
> > down after warming up. I thought maybe the vacuum adv. on the
> > distributor might be bad, but verifing timing (pulling hoses and
> > blocking/ chk timing) all are alright (car does not rev up and dwn when
> > I do this). But once I put the hoses back same thing. If I pull the
> > hose closest to the front end of the car, the engine stops rev'ing up
> > and dwn. Another thing I did is replacing the all hoses to vacuum adv,
> > I disconnected the power plug to the vacuum control module (left
> > portion of firewall) and the car stops rev'ing up and down.
> > SUGGESTIONS????
I agree with the above suggestion to bleed the coolant. The most common
problem associated with the idle cycling up and down is usually due to a
lack of coolant flowing through the cold start valve. The valve is item
number 8 in this diagram http://tinyurl.com/xj18. If the valve doesn't warm
up as the engine warms up (from coolant flowing through the bottom part),
the PGMFI system will misinterpret the condition and idle cycling results.
The first thing to due is to check the valve and make sure that the lower
part of the valve gets hot as the engine warms up. If the valve doesn't get
hot, try bleeding the coolant and make sure that coolant is flowing through
the valve. You can double check the valve as a source of the cycling by
removing the two screws from the top along with the oval shaped plate and
push down on the inner valve/plunger in the center. The cycling should stop
if the valve is the problem. If the valve is getting hot and pushing the
inner plunger down stops the cycling, then the valve likely needs to be
replaced.
Eric
12-03-2003, 12:36 PM
#14
Guest
Posts: n/a
Re: 1988 Honda Accord Lxi rev'ing Up and Down
Indian Summer,
To clarify, I think you mean to bleed the AIR that's trapped in the
cooling system (at the provided nipple) rather than DRAIN the coolant.
Some folks wouldn't know that there is a difference.
'Curly'
------------------------------
Indian Summer wrote:
> Best I can think of: turn the heat to max and bleed coolant. Remove the
> battery for a minute to reset ECU.
>
>
>>My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and down
>>after warming up. I thought maybe the vacuum adv. on the distributor
>>might be bad, but verifing timing (pulling hoses and blocking/ chk
>>timing) all are alright (car does not rev up and dwn when I do this).
>>But once I put the hoses back same thing. If I pull the hose closest to
>>the front end of the car, the engine stops rev'ing up and dwn. Another
>>thing I did is replacing the all hoses to vacuum adv, I disconnected the
>>power plug to the vacuum control module (left portion of firewall) and the
>>car stops rev'ing up and down. SUGGESTIONS????
>
To clarify, I think you mean to bleed the AIR that's trapped in the
cooling system (at the provided nipple) rather than DRAIN the coolant.
Some folks wouldn't know that there is a difference.
'Curly'
------------------------------
Indian Summer wrote:
> Best I can think of: turn the heat to max and bleed coolant. Remove the
> battery for a minute to reset ECU.
>
>
>>My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and down
>>after warming up. I thought maybe the vacuum adv. on the distributor
>>might be bad, but verifing timing (pulling hoses and blocking/ chk
>>timing) all are alright (car does not rev up and dwn when I do this).
>>But once I put the hoses back same thing. If I pull the hose closest to
>>the front end of the car, the engine stops rev'ing up and dwn. Another
>>thing I did is replacing the all hoses to vacuum adv, I disconnected the
>>power plug to the vacuum control module (left portion of firewall) and the
>>car stops rev'ing up and down. SUGGESTIONS????
>
12-03-2003, 12:36 PM
#15
Guest
Posts: n/a
Re: 1988 Honda Accord Lxi rev'ing Up and Down
Indian Summer,
To clarify, I think you mean to bleed the AIR that's trapped in the
cooling system (at the provided nipple) rather than DRAIN the coolant.
Some folks wouldn't know that there is a difference.
'Curly'
------------------------------
Indian Summer wrote:
> Best I can think of: turn the heat to max and bleed coolant. Remove the
> battery for a minute to reset ECU.
>
>
>>My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and down
>>after warming up. I thought maybe the vacuum adv. on the distributor
>>might be bad, but verifing timing (pulling hoses and blocking/ chk
>>timing) all are alright (car does not rev up and dwn when I do this).
>>But once I put the hoses back same thing. If I pull the hose closest to
>>the front end of the car, the engine stops rev'ing up and dwn. Another
>>thing I did is replacing the all hoses to vacuum adv, I disconnected the
>>power plug to the vacuum control module (left portion of firewall) and the
>>car stops rev'ing up and down. SUGGESTIONS????
>
To clarify, I think you mean to bleed the AIR that's trapped in the
cooling system (at the provided nipple) rather than DRAIN the coolant.
Some folks wouldn't know that there is a difference.
'Curly'
------------------------------
Indian Summer wrote:
> Best I can think of: turn the heat to max and bleed coolant. Remove the
> battery for a minute to reset ECU.
>
>
>>My 88 Honda Accord Lxi with 200K plus milage started rev'ing up and down
>>after warming up. I thought maybe the vacuum adv. on the distributor
>>might be bad, but verifing timing (pulling hoses and blocking/ chk
>>timing) all are alright (car does not rev up and dwn when I do this).
>>But once I put the hoses back same thing. If I pull the hose closest to
>>the front end of the car, the engine stops rev'ing up and dwn. Another
>>thing I did is replacing the all hoses to vacuum adv, I disconnected the
>>power plug to the vacuum control module (left portion of firewall) and the
>>car stops rev'ing up and down. SUGGESTIONS????
>
