'92 Civic DX Hatchback Idle dropout problem
#76
Guest
Posts: n/a
Re: '92 Civic DX Hatchback Idle dropout problem
david.borhani@alum.mit.edu wrote:
>> after all this, you may not need the idle adjust done at all! add valve
>> lash to the list of things to do as now's the time to do it with all the
>> covers off.
>
> They did the valve clearance adjustment, twice! First time car seemed
> like it didn't just have tons of work done ---- felt even "older".
> After I insisted, they re-checked clearance, found it "way too loose",
> and corrected it, at which point the car is now, with much improved
> idle problem. The offset T-belt shouldn't affect valve clearance,
> should it? Or does the T-belt/timing need to be correct so that you
> know that the valve is closed/open the right amount at the right time?
> (Is valve lash is same as valve clearance?)
>
cam timing affects performance big time. valve lash much less so, but
still a factor.
either way, judging by your experience with these guys, you should
consider absorbing the extra cost and just take it to an independent
honda specialist. continued ineptitude will cost you a good deal more
in the long run. if you want to take it back to the same place to prove
a point, /insist/ on having a senior mechanic do the work. insist on
meeting them - before and after.
>> after all this, you may not need the idle adjust done at all! add valve
>> lash to the list of things to do as now's the time to do it with all the
>> covers off.
>
> They did the valve clearance adjustment, twice! First time car seemed
> like it didn't just have tons of work done ---- felt even "older".
> After I insisted, they re-checked clearance, found it "way too loose",
> and corrected it, at which point the car is now, with much improved
> idle problem. The offset T-belt shouldn't affect valve clearance,
> should it? Or does the T-belt/timing need to be correct so that you
> know that the valve is closed/open the right amount at the right time?
> (Is valve lash is same as valve clearance?)
>
cam timing affects performance big time. valve lash much less so, but
still a factor.
either way, judging by your experience with these guys, you should
consider absorbing the extra cost and just take it to an independent
honda specialist. continued ineptitude will cost you a good deal more
in the long run. if you want to take it back to the same place to prove
a point, /insist/ on having a senior mechanic do the work. insist on
meeting them - before and after.
#77
Guest
Posts: n/a
Re: '92 Civic DX Hatchback Idle dropout problem
> if you want to take it back to the same place to prove a point, /insist/ on having a senior mechanic do the work.
> insist on meeting them - before and after.
I'm a glutton for punishment, I guess. Back to Honda this morning, met
w/ the sr. mech. He seems sharp (as wasn't the one who did the
incorrect valve lash the 1st time). They tore it apart, and together
we examined the timing marks. They actually did the T-belt right,
which is a relief. The confusion is shown well here,
http://www.cadvision.com/blanchas/54pontiac/honda.html ; you use the
horiz. marks on the cam pulley for the 1.5L engine (which I have), and
at the pointer for the 1.6L VTEC. Also, there's two white marks
painted on the *inside* of the cam pulley, that line up w/ the cyl.
head for the 1.5L.
That settled, they're a bit at a loss as to why the distr. is set so
far forward. But, will replace distr. head & rotor w/ genuine Honda,
as they say they've had bad experiences w/ off-brand parts.
IACV/idle stumble also clearly still bothers them. Coolant was indeed
bled to remove bubbles. They're putting in a new thermostat. When I
disconnected the IACV elec. conn., it should have generated an Check
Engine code, but it didn't. Hmmm. They also are thinking that there
could be a blockage inside the throttle body. Any more suggestions/
ideas RE: IACV/idle?
> insist on meeting them - before and after.
I'm a glutton for punishment, I guess. Back to Honda this morning, met
w/ the sr. mech. He seems sharp (as wasn't the one who did the
incorrect valve lash the 1st time). They tore it apart, and together
we examined the timing marks. They actually did the T-belt right,
which is a relief. The confusion is shown well here,
http://www.cadvision.com/blanchas/54pontiac/honda.html ; you use the
horiz. marks on the cam pulley for the 1.5L engine (which I have), and
at the pointer for the 1.6L VTEC. Also, there's two white marks
painted on the *inside* of the cam pulley, that line up w/ the cyl.
head for the 1.5L.
That settled, they're a bit at a loss as to why the distr. is set so
far forward. But, will replace distr. head & rotor w/ genuine Honda,
as they say they've had bad experiences w/ off-brand parts.
IACV/idle stumble also clearly still bothers them. Coolant was indeed
bled to remove bubbles. They're putting in a new thermostat. When I
disconnected the IACV elec. conn., it should have generated an Check
Engine code, but it didn't. Hmmm. They also are thinking that there
could be a blockage inside the throttle body. Any more suggestions/
ideas RE: IACV/idle?
#78
Guest
Posts: n/a
Re: '92 Civic DX Hatchback Idle dropout problem
> if you want to take it back to the same place to prove a point, /insist/ on having a senior mechanic do the work.
> insist on meeting them - before and after.
I'm a glutton for punishment, I guess. Back to Honda this morning, met
w/ the sr. mech. He seems sharp (as wasn't the one who did the
incorrect valve lash the 1st time). They tore it apart, and together
we examined the timing marks. They actually did the T-belt right,
which is a relief. The confusion is shown well here,
http://www.cadvision.com/blanchas/54pontiac/honda.html ; you use the
horiz. marks on the cam pulley for the 1.5L engine (which I have), and
at the pointer for the 1.6L VTEC. Also, there's two white marks
painted on the *inside* of the cam pulley, that line up w/ the cyl.
head for the 1.5L.
That settled, they're a bit at a loss as to why the distr. is set so
far forward. But, will replace distr. head & rotor w/ genuine Honda,
as they say they've had bad experiences w/ off-brand parts.
IACV/idle stumble also clearly still bothers them. Coolant was indeed
bled to remove bubbles. They're putting in a new thermostat. When I
disconnected the IACV elec. conn., it should have generated an Check
Engine code, but it didn't. Hmmm. They also are thinking that there
could be a blockage inside the throttle body. Any more suggestions/
ideas RE: IACV/idle?
> insist on meeting them - before and after.
I'm a glutton for punishment, I guess. Back to Honda this morning, met
w/ the sr. mech. He seems sharp (as wasn't the one who did the
incorrect valve lash the 1st time). They tore it apart, and together
we examined the timing marks. They actually did the T-belt right,
which is a relief. The confusion is shown well here,
http://www.cadvision.com/blanchas/54pontiac/honda.html ; you use the
horiz. marks on the cam pulley for the 1.5L engine (which I have), and
at the pointer for the 1.6L VTEC. Also, there's two white marks
painted on the *inside* of the cam pulley, that line up w/ the cyl.
head for the 1.5L.
That settled, they're a bit at a loss as to why the distr. is set so
far forward. But, will replace distr. head & rotor w/ genuine Honda,
as they say they've had bad experiences w/ off-brand parts.
IACV/idle stumble also clearly still bothers them. Coolant was indeed
bled to remove bubbles. They're putting in a new thermostat. When I
disconnected the IACV elec. conn., it should have generated an Check
Engine code, but it didn't. Hmmm. They also are thinking that there
could be a blockage inside the throttle body. Any more suggestions/
ideas RE: IACV/idle?
#79
Guest
Posts: n/a
Re: '92 Civic DX Hatchback Idle dropout problem
> if you want to take it back to the same place to prove a point, /insist/ on having a senior mechanic do the work.
> insist on meeting them - before and after.
I'm a glutton for punishment, I guess. Back to Honda this morning, met
w/ the sr. mech. He seems sharp (as wasn't the one who did the
incorrect valve lash the 1st time). They tore it apart, and together
we examined the timing marks. They actually did the T-belt right,
which is a relief. The confusion is shown well here,
http://www.cadvision.com/blanchas/54pontiac/honda.html ; you use the
horiz. marks on the cam pulley for the 1.5L engine (which I have), and
at the pointer for the 1.6L VTEC. Also, there's two white marks
painted on the *inside* of the cam pulley, that line up w/ the cyl.
head for the 1.5L.
That settled, they're a bit at a loss as to why the distr. is set so
far forward. But, will replace distr. head & rotor w/ genuine Honda,
as they say they've had bad experiences w/ off-brand parts.
IACV/idle stumble also clearly still bothers them. Coolant was indeed
bled to remove bubbles. They're putting in a new thermostat. When I
disconnected the IACV elec. conn., it should have generated an Check
Engine code, but it didn't. Hmmm. They also are thinking that there
could be a blockage inside the throttle body. Any more suggestions/
ideas RE: IACV/idle?
> insist on meeting them - before and after.
I'm a glutton for punishment, I guess. Back to Honda this morning, met
w/ the sr. mech. He seems sharp (as wasn't the one who did the
incorrect valve lash the 1st time). They tore it apart, and together
we examined the timing marks. They actually did the T-belt right,
which is a relief. The confusion is shown well here,
http://www.cadvision.com/blanchas/54pontiac/honda.html ; you use the
horiz. marks on the cam pulley for the 1.5L engine (which I have), and
at the pointer for the 1.6L VTEC. Also, there's two white marks
painted on the *inside* of the cam pulley, that line up w/ the cyl.
head for the 1.5L.
That settled, they're a bit at a loss as to why the distr. is set so
far forward. But, will replace distr. head & rotor w/ genuine Honda,
as they say they've had bad experiences w/ off-brand parts.
IACV/idle stumble also clearly still bothers them. Coolant was indeed
bled to remove bubbles. They're putting in a new thermostat. When I
disconnected the IACV elec. conn., it should have generated an Check
Engine code, but it didn't. Hmmm. They also are thinking that there
could be a blockage inside the throttle body. Any more suggestions/
ideas RE: IACV/idle?
Thread
Thread Starter
Forum
Replies
Last Post
david.borhani@alum.mit.edu
Honda Mailing List
0
06-21-2007 06:55 PM
david.borhani@alum.mit.edu
Honda Mailing List
0
06-21-2007 06:55 PM
Richard
Honda Mailing List
8
01-18-2004 12:51 AM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)