Brake Flush Bleeder Bolt Adapters?
#16
Guest
Posts: n/a
Re: Brake Flush Bleeder Bolt Adapters?
Jim Yanik wrote:
> "Bruce" <andrew.bruce@regions.com> wrote in
> news:1146083076.777984.140290@i39g2000cwa.googlegr oups.com:
>
>
>>I second the pressure bleeding method... I bought one of the bug
>>sprayer models a few years ago and it seriously could not be easier. No
>>helper necessary. Besides, I've read in several posts that the helper
>>pumping method can sometimes ruin the seals on your master cylinder if
>>there's corrosion on the plunger.
>
>
> If there's corrosion on the master cylinder plunger or MC bore,the MC
> already needs replacing or rebuilding.
damned right!!! fear of not using the full cylinder stroke in case of
encountering this problem blows my mind. this is the #1 safety
component of the vehicle. better make sure it's 100%.
>
>
>
>>One caution if you get the bug sprayer bleeder ... be sure to release
>>the pressure in the bottle before you undo the fitting on your master
>>cylinder resevoir or you'll get a nasty mess. Brake fluid will spray
>>EVERYWHERE.
>>
>>
>
>
> Does the "bug sprayer" keep the reservoir filled so air does not enter the
> MC?
>
> "Bruce" <andrew.bruce@regions.com> wrote in
> news:1146083076.777984.140290@i39g2000cwa.googlegr oups.com:
>
>
>>I second the pressure bleeding method... I bought one of the bug
>>sprayer models a few years ago and it seriously could not be easier. No
>>helper necessary. Besides, I've read in several posts that the helper
>>pumping method can sometimes ruin the seals on your master cylinder if
>>there's corrosion on the plunger.
>
>
> If there's corrosion on the master cylinder plunger or MC bore,the MC
> already needs replacing or rebuilding.
damned right!!! fear of not using the full cylinder stroke in case of
encountering this problem blows my mind. this is the #1 safety
component of the vehicle. better make sure it's 100%.
>
>
>
>>One caution if you get the bug sprayer bleeder ... be sure to release
>>the pressure in the bottle before you undo the fitting on your master
>>cylinder resevoir or you'll get a nasty mess. Brake fluid will spray
>>EVERYWHERE.
>>
>>
>
>
> Does the "bug sprayer" keep the reservoir filled so air does not enter the
> MC?
>
#17
Guest
Posts: n/a
Re: Brake Flush Bleeder Bolt Adapters?
"SoCalMike" <Mikein562athotmail@hotmail.com> wrote
> Elle wrote:
>> Can anyone make other suggestions?
>
> i took off the bleeder screws and wrapped the threads with
> teflon tape.
>
> home depot/lowes should have some vinyl hose that will
> tightly slip on the nipple.
>
> otherwise, i know there are rubber 90 degree bleeder arms
> that would work, and that should have come with your
> mityvac set.
Yes, there are several 90-degree nipples, but none that fit
the rears. I am using one of the cone-shaped ones, and it's
a poor fit into the bleeder bolt.
I like the HD/Lowes idea. I'll go looking for a good fit
soon and use some of the adapters to go from small tube
diameter to the larger diameter hose that came with the
Mity-Vac kit.
To the others: I want to stick with the Mity-Vac approach a
bit longer.
> Elle wrote:
>> Can anyone make other suggestions?
>
> i took off the bleeder screws and wrapped the threads with
> teflon tape.
>
> home depot/lowes should have some vinyl hose that will
> tightly slip on the nipple.
>
> otherwise, i know there are rubber 90 degree bleeder arms
> that would work, and that should have come with your
> mityvac set.
Yes, there are several 90-degree nipples, but none that fit
the rears. I am using one of the cone-shaped ones, and it's
a poor fit into the bleeder bolt.
I like the HD/Lowes idea. I'll go looking for a good fit
soon and use some of the adapters to go from small tube
diameter to the larger diameter hose that came with the
Mity-Vac kit.
To the others: I want to stick with the Mity-Vac approach a
bit longer.
#18
Guest
Posts: n/a
Re: Brake Flush Bleeder Bolt Adapters?
"SoCalMike" <Mikein562athotmail@hotmail.com> wrote
> Elle wrote:
>> Can anyone make other suggestions?
>
> i took off the bleeder screws and wrapped the threads with
> teflon tape.
>
> home depot/lowes should have some vinyl hose that will
> tightly slip on the nipple.
>
> otherwise, i know there are rubber 90 degree bleeder arms
> that would work, and that should have come with your
> mityvac set.
Yes, there are several 90-degree nipples, but none that fit
the rears. I am using one of the cone-shaped ones, and it's
a poor fit into the bleeder bolt.
I like the HD/Lowes idea. I'll go looking for a good fit
soon and use some of the adapters to go from small tube
diameter to the larger diameter hose that came with the
Mity-Vac kit.
To the others: I want to stick with the Mity-Vac approach a
bit longer.
> Elle wrote:
>> Can anyone make other suggestions?
>
> i took off the bleeder screws and wrapped the threads with
> teflon tape.
>
> home depot/lowes should have some vinyl hose that will
> tightly slip on the nipple.
>
> otherwise, i know there are rubber 90 degree bleeder arms
> that would work, and that should have come with your
> mityvac set.
Yes, there are several 90-degree nipples, but none that fit
the rears. I am using one of the cone-shaped ones, and it's
a poor fit into the bleeder bolt.
I like the HD/Lowes idea. I'll go looking for a good fit
soon and use some of the adapters to go from small tube
diameter to the larger diameter hose that came with the
Mity-Vac kit.
To the others: I want to stick with the Mity-Vac approach a
bit longer.
#19
Guest
Posts: n/a
Re: Brake Flush Bleeder Bolt Adapters?
"SoCalMike" <Mikein562athotmail@hotmail.com> wrote
> Elle wrote:
>> Can anyone make other suggestions?
>
> i took off the bleeder screws and wrapped the threads with
> teflon tape.
>
> home depot/lowes should have some vinyl hose that will
> tightly slip on the nipple.
>
> otherwise, i know there are rubber 90 degree bleeder arms
> that would work, and that should have come with your
> mityvac set.
Yes, there are several 90-degree nipples, but none that fit
the rears. I am using one of the cone-shaped ones, and it's
a poor fit into the bleeder bolt.
I like the HD/Lowes idea. I'll go looking for a good fit
soon and use some of the adapters to go from small tube
diameter to the larger diameter hose that came with the
Mity-Vac kit.
To the others: I want to stick with the Mity-Vac approach a
bit longer.
> Elle wrote:
>> Can anyone make other suggestions?
>
> i took off the bleeder screws and wrapped the threads with
> teflon tape.
>
> home depot/lowes should have some vinyl hose that will
> tightly slip on the nipple.
>
> otherwise, i know there are rubber 90 degree bleeder arms
> that would work, and that should have come with your
> mityvac set.
Yes, there are several 90-degree nipples, but none that fit
the rears. I am using one of the cone-shaped ones, and it's
a poor fit into the bleeder bolt.
I like the HD/Lowes idea. I'll go looking for a good fit
soon and use some of the adapters to go from small tube
diameter to the larger diameter hose that came with the
Mity-Vac kit.
To the others: I want to stick with the Mity-Vac approach a
bit longer.
#20
Guest
Posts: n/a
Re: Brake Flush Bleeder Bolt Adapters?
Elle wrote:
> "SoCalMike" <Mikein562athotmail@hotmail.com> wrote
>> Elle wrote:
>>> Can anyone make other suggestions?
>> i took off the bleeder screws and wrapped the threads with
>> teflon tape.
>>
>> home depot/lowes should have some vinyl hose that will
>> tightly slip on the nipple.
>>
>> otherwise, i know there are rubber 90 degree bleeder arms
>> that would work, and that should have come with your
>> mityvac set.
>
> Yes, there are several 90-degree nipples, but none that fit
> the rears. I am using one of the cone-shaped ones, and it's
> a poor fit into the bleeder bolt.
>
> I like the HD/Lowes idea. I'll go looking for a good fit
> soon and use some of the adapters to go from small tube
> diameter to the larger diameter hose that came with the
> Mity-Vac kit.
who knows? the small tube might "interference fit" inside the mityvac
tubing.
>
> To the others: I want to stick with the Mity-Vac approach a
> bit longer.
i like my mityvac. unscrew the bleeder, pump it a couple times, eye on
the brake fluid reservoir. once it starts coming out "straw colored", im
done.
> "SoCalMike" <Mikein562athotmail@hotmail.com> wrote
>> Elle wrote:
>>> Can anyone make other suggestions?
>> i took off the bleeder screws and wrapped the threads with
>> teflon tape.
>>
>> home depot/lowes should have some vinyl hose that will
>> tightly slip on the nipple.
>>
>> otherwise, i know there are rubber 90 degree bleeder arms
>> that would work, and that should have come with your
>> mityvac set.
>
> Yes, there are several 90-degree nipples, but none that fit
> the rears. I am using one of the cone-shaped ones, and it's
> a poor fit into the bleeder bolt.
>
> I like the HD/Lowes idea. I'll go looking for a good fit
> soon and use some of the adapters to go from small tube
> diameter to the larger diameter hose that came with the
> Mity-Vac kit.
who knows? the small tube might "interference fit" inside the mityvac
tubing.
>
> To the others: I want to stick with the Mity-Vac approach a
> bit longer.
i like my mityvac. unscrew the bleeder, pump it a couple times, eye on
the brake fluid reservoir. once it starts coming out "straw colored", im
done.
#21
Guest
Posts: n/a
Re: Brake Flush Bleeder Bolt Adapters?
Elle wrote:
> "SoCalMike" <Mikein562athotmail@hotmail.com> wrote
>> Elle wrote:
>>> Can anyone make other suggestions?
>> i took off the bleeder screws and wrapped the threads with
>> teflon tape.
>>
>> home depot/lowes should have some vinyl hose that will
>> tightly slip on the nipple.
>>
>> otherwise, i know there are rubber 90 degree bleeder arms
>> that would work, and that should have come with your
>> mityvac set.
>
> Yes, there are several 90-degree nipples, but none that fit
> the rears. I am using one of the cone-shaped ones, and it's
> a poor fit into the bleeder bolt.
>
> I like the HD/Lowes idea. I'll go looking for a good fit
> soon and use some of the adapters to go from small tube
> diameter to the larger diameter hose that came with the
> Mity-Vac kit.
who knows? the small tube might "interference fit" inside the mityvac
tubing.
>
> To the others: I want to stick with the Mity-Vac approach a
> bit longer.
i like my mityvac. unscrew the bleeder, pump it a couple times, eye on
the brake fluid reservoir. once it starts coming out "straw colored", im
done.
> "SoCalMike" <Mikein562athotmail@hotmail.com> wrote
>> Elle wrote:
>>> Can anyone make other suggestions?
>> i took off the bleeder screws and wrapped the threads with
>> teflon tape.
>>
>> home depot/lowes should have some vinyl hose that will
>> tightly slip on the nipple.
>>
>> otherwise, i know there are rubber 90 degree bleeder arms
>> that would work, and that should have come with your
>> mityvac set.
>
> Yes, there are several 90-degree nipples, but none that fit
> the rears. I am using one of the cone-shaped ones, and it's
> a poor fit into the bleeder bolt.
>
> I like the HD/Lowes idea. I'll go looking for a good fit
> soon and use some of the adapters to go from small tube
> diameter to the larger diameter hose that came with the
> Mity-Vac kit.
who knows? the small tube might "interference fit" inside the mityvac
tubing.
>
> To the others: I want to stick with the Mity-Vac approach a
> bit longer.
i like my mityvac. unscrew the bleeder, pump it a couple times, eye on
the brake fluid reservoir. once it starts coming out "straw colored", im
done.
#22
Guest
Posts: n/a
Re: Brake Flush Bleeder Bolt Adapters?
Elle wrote:
> "SoCalMike" <Mikein562athotmail@hotmail.com> wrote
>> Elle wrote:
>>> Can anyone make other suggestions?
>> i took off the bleeder screws and wrapped the threads with
>> teflon tape.
>>
>> home depot/lowes should have some vinyl hose that will
>> tightly slip on the nipple.
>>
>> otherwise, i know there are rubber 90 degree bleeder arms
>> that would work, and that should have come with your
>> mityvac set.
>
> Yes, there are several 90-degree nipples, but none that fit
> the rears. I am using one of the cone-shaped ones, and it's
> a poor fit into the bleeder bolt.
>
> I like the HD/Lowes idea. I'll go looking for a good fit
> soon and use some of the adapters to go from small tube
> diameter to the larger diameter hose that came with the
> Mity-Vac kit.
who knows? the small tube might "interference fit" inside the mityvac
tubing.
>
> To the others: I want to stick with the Mity-Vac approach a
> bit longer.
i like my mityvac. unscrew the bleeder, pump it a couple times, eye on
the brake fluid reservoir. once it starts coming out "straw colored", im
done.
> "SoCalMike" <Mikein562athotmail@hotmail.com> wrote
>> Elle wrote:
>>> Can anyone make other suggestions?
>> i took off the bleeder screws and wrapped the threads with
>> teflon tape.
>>
>> home depot/lowes should have some vinyl hose that will
>> tightly slip on the nipple.
>>
>> otherwise, i know there are rubber 90 degree bleeder arms
>> that would work, and that should have come with your
>> mityvac set.
>
> Yes, there are several 90-degree nipples, but none that fit
> the rears. I am using one of the cone-shaped ones, and it's
> a poor fit into the bleeder bolt.
>
> I like the HD/Lowes idea. I'll go looking for a good fit
> soon and use some of the adapters to go from small tube
> diameter to the larger diameter hose that came with the
> Mity-Vac kit.
who knows? the small tube might "interference fit" inside the mityvac
tubing.
>
> To the others: I want to stick with the Mity-Vac approach a
> bit longer.
i like my mityvac. unscrew the bleeder, pump it a couple times, eye on
the brake fluid reservoir. once it starts coming out "straw colored", im
done.
#23
Guest
Posts: n/a
Re: Brake Flush Bleeder Bolt Adapters?
"SoCalMike" <Mikein562athotmail@hotmail.com> wrote
> who knows? the small tube might "interference fit" inside
> the mityvac tubing.
Maybe so.
>> To the others: I want to stick with the Mity-Vac approach
>> a bit longer.
>
> i like my mityvac. unscrew the bleeder, pump it a couple
> times, eye on the brake fluid reservoir. once it starts
> coming out "straw colored", im done.
It sure seemed easy this second time around. Though I have a
new floor jack and now four jack stands, and that helped.
About how much brake fluid do you tend to end up using on a
flush?
> who knows? the small tube might "interference fit" inside
> the mityvac tubing.
Maybe so.
>> To the others: I want to stick with the Mity-Vac approach
>> a bit longer.
>
> i like my mityvac. unscrew the bleeder, pump it a couple
> times, eye on the brake fluid reservoir. once it starts
> coming out "straw colored", im done.
It sure seemed easy this second time around. Though I have a
new floor jack and now four jack stands, and that helped.
About how much brake fluid do you tend to end up using on a
flush?
#24
Guest
Posts: n/a
Re: Brake Flush Bleeder Bolt Adapters?
"SoCalMike" <Mikein562athotmail@hotmail.com> wrote
> who knows? the small tube might "interference fit" inside
> the mityvac tubing.
Maybe so.
>> To the others: I want to stick with the Mity-Vac approach
>> a bit longer.
>
> i like my mityvac. unscrew the bleeder, pump it a couple
> times, eye on the brake fluid reservoir. once it starts
> coming out "straw colored", im done.
It sure seemed easy this second time around. Though I have a
new floor jack and now four jack stands, and that helped.
About how much brake fluid do you tend to end up using on a
flush?
> who knows? the small tube might "interference fit" inside
> the mityvac tubing.
Maybe so.
>> To the others: I want to stick with the Mity-Vac approach
>> a bit longer.
>
> i like my mityvac. unscrew the bleeder, pump it a couple
> times, eye on the brake fluid reservoir. once it starts
> coming out "straw colored", im done.
It sure seemed easy this second time around. Though I have a
new floor jack and now four jack stands, and that helped.
About how much brake fluid do you tend to end up using on a
flush?
#25
Guest
Posts: n/a
Re: Brake Flush Bleeder Bolt Adapters?
"SoCalMike" <Mikein562athotmail@hotmail.com> wrote
> who knows? the small tube might "interference fit" inside
> the mityvac tubing.
Maybe so.
>> To the others: I want to stick with the Mity-Vac approach
>> a bit longer.
>
> i like my mityvac. unscrew the bleeder, pump it a couple
> times, eye on the brake fluid reservoir. once it starts
> coming out "straw colored", im done.
It sure seemed easy this second time around. Though I have a
new floor jack and now four jack stands, and that helped.
About how much brake fluid do you tend to end up using on a
flush?
> who knows? the small tube might "interference fit" inside
> the mityvac tubing.
Maybe so.
>> To the others: I want to stick with the Mity-Vac approach
>> a bit longer.
>
> i like my mityvac. unscrew the bleeder, pump it a couple
> times, eye on the brake fluid reservoir. once it starts
> coming out "straw colored", im done.
It sure seemed easy this second time around. Though I have a
new floor jack and now four jack stands, and that helped.
About how much brake fluid do you tend to end up using on a
flush?
#26
Guest
Posts: n/a
Re: Brake Flush Bleeder Bolt Adapters?
Elle wrote:
> ...I did a brake flush yesterday, by myself for the second
> time, on my 91 Civic LX (176k miles). I use the Mity-Vac
> system ( a hand-held vacuum pump, connecting to a small
> container to collect fluid, tubing, and adapters).
Hi Elle. No answers, but a few ? Where is a good source to
buy the Mity-Vac?
>
> I am thinking of buying a set of those one-way (that is,
> check) bleeder valves that Pep Boys, for one, sells, to (1)
> maybe get a better fit from adapter to valve; and (2)
> minimize air introduction into the rear brake system.
I'm getting ready to do a flush. Any trouble getting the
bleeders off? I don't know when mine were last touched,
& hope they don't cause trouble.
..... I used a 32 oz ( = two pints) container of Valvoline
> "exceeds DOT 3 and 4 requirements" brake fluid for the
> flush.
I plan on using Motul Dot 5.1 fluid. Anyone have any
comments on this?
Mike
> ...I did a brake flush yesterday, by myself for the second
> time, on my 91 Civic LX (176k miles). I use the Mity-Vac
> system ( a hand-held vacuum pump, connecting to a small
> container to collect fluid, tubing, and adapters).
Hi Elle. No answers, but a few ? Where is a good source to
buy the Mity-Vac?
>
> I am thinking of buying a set of those one-way (that is,
> check) bleeder valves that Pep Boys, for one, sells, to (1)
> maybe get a better fit from adapter to valve; and (2)
> minimize air introduction into the rear brake system.
I'm getting ready to do a flush. Any trouble getting the
bleeders off? I don't know when mine were last touched,
& hope they don't cause trouble.
..... I used a 32 oz ( = two pints) container of Valvoline
> "exceeds DOT 3 and 4 requirements" brake fluid for the
> flush.
I plan on using Motul Dot 5.1 fluid. Anyone have any
comments on this?
Mike
#27
Guest
Posts: n/a
Re: Brake Flush Bleeder Bolt Adapters?
Elle wrote:
> ...I did a brake flush yesterday, by myself for the second
> time, on my 91 Civic LX (176k miles). I use the Mity-Vac
> system ( a hand-held vacuum pump, connecting to a small
> container to collect fluid, tubing, and adapters).
Hi Elle. No answers, but a few ? Where is a good source to
buy the Mity-Vac?
>
> I am thinking of buying a set of those one-way (that is,
> check) bleeder valves that Pep Boys, for one, sells, to (1)
> maybe get a better fit from adapter to valve; and (2)
> minimize air introduction into the rear brake system.
I'm getting ready to do a flush. Any trouble getting the
bleeders off? I don't know when mine were last touched,
& hope they don't cause trouble.
..... I used a 32 oz ( = two pints) container of Valvoline
> "exceeds DOT 3 and 4 requirements" brake fluid for the
> flush.
I plan on using Motul Dot 5.1 fluid. Anyone have any
comments on this?
Mike
> ...I did a brake flush yesterday, by myself for the second
> time, on my 91 Civic LX (176k miles). I use the Mity-Vac
> system ( a hand-held vacuum pump, connecting to a small
> container to collect fluid, tubing, and adapters).
Hi Elle. No answers, but a few ? Where is a good source to
buy the Mity-Vac?
>
> I am thinking of buying a set of those one-way (that is,
> check) bleeder valves that Pep Boys, for one, sells, to (1)
> maybe get a better fit from adapter to valve; and (2)
> minimize air introduction into the rear brake system.
I'm getting ready to do a flush. Any trouble getting the
bleeders off? I don't know when mine were last touched,
& hope they don't cause trouble.
..... I used a 32 oz ( = two pints) container of Valvoline
> "exceeds DOT 3 and 4 requirements" brake fluid for the
> flush.
I plan on using Motul Dot 5.1 fluid. Anyone have any
comments on this?
Mike
#28
Guest
Posts: n/a
Re: Brake Flush Bleeder Bolt Adapters?
Elle wrote:
> ...I did a brake flush yesterday, by myself for the second
> time, on my 91 Civic LX (176k miles). I use the Mity-Vac
> system ( a hand-held vacuum pump, connecting to a small
> container to collect fluid, tubing, and adapters).
Hi Elle. No answers, but a few ? Where is a good source to
buy the Mity-Vac?
>
> I am thinking of buying a set of those one-way (that is,
> check) bleeder valves that Pep Boys, for one, sells, to (1)
> maybe get a better fit from adapter to valve; and (2)
> minimize air introduction into the rear brake system.
I'm getting ready to do a flush. Any trouble getting the
bleeders off? I don't know when mine were last touched,
& hope they don't cause trouble.
..... I used a 32 oz ( = two pints) container of Valvoline
> "exceeds DOT 3 and 4 requirements" brake fluid for the
> flush.
I plan on using Motul Dot 5.1 fluid. Anyone have any
comments on this?
Mike
> ...I did a brake flush yesterday, by myself for the second
> time, on my 91 Civic LX (176k miles). I use the Mity-Vac
> system ( a hand-held vacuum pump, connecting to a small
> container to collect fluid, tubing, and adapters).
Hi Elle. No answers, but a few ? Where is a good source to
buy the Mity-Vac?
>
> I am thinking of buying a set of those one-way (that is,
> check) bleeder valves that Pep Boys, for one, sells, to (1)
> maybe get a better fit from adapter to valve; and (2)
> minimize air introduction into the rear brake system.
I'm getting ready to do a flush. Any trouble getting the
bleeders off? I don't know when mine were last touched,
& hope they don't cause trouble.
..... I used a 32 oz ( = two pints) container of Valvoline
> "exceeds DOT 3 and 4 requirements" brake fluid for the
> flush.
I plan on using Motul Dot 5.1 fluid. Anyone have any
comments on this?
Mike
#29
Guest
Posts: n/a
Re: Brake Flush Bleeder Bolt Adapters?
"Mike Doyle" <sigifrith@frontiernet.net> wrote
> Elle wrote:
>> ...I did a brake flush yesterday, by myself for the
>> second time, on my 91 Civic LX (176k miles). I use the
>> Mity-Vac system ( a hand-held vacuum pump, connecting to
>> a small container to collect fluid, tubing, and
>> adapters).
>
> Hi Elle. No answers, but a few ? Where is a good source
> to
> buy the Mity-Vac?
The Mity-Vac (metal pump) kit I bought for around $40 is the
following:
http://www.harborfreight.com/cpi/cta...temnumber=2068
It's on sale for about $40 now. Take a printout of the site
above with you to the store to get the sale price.
Harbor Freight also sells a plastic pump version for around
$32. It is probably just fine.
From googling more on this, a lot of people have had "one
person brake bleed/flush" success with "Speed Bleeder
valves." One removes the old bleeder bolts and installs
these in their place. See site www.speedbleeder.com . Pep
Boys sells these one way (= check) valves, too.
>> I am thinking of buying a set of those one-way (that is,
>> check) bleeder valves that Pep Boys, for one, sells, to
>> (1) maybe get a better fit from adapter to valve; and (2)
>> minimize air introduction into the rear brake system.
>
> I'm getting ready to do a flush. Any trouble getting the
> bleeders off?
No, though if it's been awhile, I'd spray down the threads
as best I could with the penetrating oil "PB Blaster"
(around $4 for a big spray can). Great stuff.
I think I have read of people overtorquing and so breaking
these tiny bolts, though. Only 7 ft-lbs. is specified in the
manual for my 91 Civic.
> I don't know when mine were last touched,
> & hope they don't cause trouble.
>
>
> .... I used a 32 oz ( = two pints) container of Valvoline
>> "exceeds DOT 3 and 4 requirements" brake fluid for the
>> flush.
>
> I plan on using Motul Dot 5.1 fluid. Anyone have any
> comments on this?
Isn't that silicone brake fluid (to be distinguished from
the "synthetic" DOT 3 and 4 brake fluids)? It doesn't mix
with the DOT 3 and 4, as I understand it. I don't think
there's much reason to use other than DOT 3 and 4. Googling
for {"Brake fluid" silicone "DOT 3"} etc. turns up a lot.
E.g. see http://www.afcoracing.com/tech_pages/fluid.shtml
Let the group know how it goes... :-) I found it a little
tricky the first time but the second time was a breeze, like
I said, though I hope to improve on the rear brakes' bleed
part.
> Elle wrote:
>> ...I did a brake flush yesterday, by myself for the
>> second time, on my 91 Civic LX (176k miles). I use the
>> Mity-Vac system ( a hand-held vacuum pump, connecting to
>> a small container to collect fluid, tubing, and
>> adapters).
>
> Hi Elle. No answers, but a few ? Where is a good source
> to
> buy the Mity-Vac?
The Mity-Vac (metal pump) kit I bought for around $40 is the
following:
http://www.harborfreight.com/cpi/cta...temnumber=2068
It's on sale for about $40 now. Take a printout of the site
above with you to the store to get the sale price.
Harbor Freight also sells a plastic pump version for around
$32. It is probably just fine.
From googling more on this, a lot of people have had "one
person brake bleed/flush" success with "Speed Bleeder
valves." One removes the old bleeder bolts and installs
these in their place. See site www.speedbleeder.com . Pep
Boys sells these one way (= check) valves, too.
>> I am thinking of buying a set of those one-way (that is,
>> check) bleeder valves that Pep Boys, for one, sells, to
>> (1) maybe get a better fit from adapter to valve; and (2)
>> minimize air introduction into the rear brake system.
>
> I'm getting ready to do a flush. Any trouble getting the
> bleeders off?
No, though if it's been awhile, I'd spray down the threads
as best I could with the penetrating oil "PB Blaster"
(around $4 for a big spray can). Great stuff.
I think I have read of people overtorquing and so breaking
these tiny bolts, though. Only 7 ft-lbs. is specified in the
manual for my 91 Civic.
> I don't know when mine were last touched,
> & hope they don't cause trouble.
>
>
> .... I used a 32 oz ( = two pints) container of Valvoline
>> "exceeds DOT 3 and 4 requirements" brake fluid for the
>> flush.
>
> I plan on using Motul Dot 5.1 fluid. Anyone have any
> comments on this?
Isn't that silicone brake fluid (to be distinguished from
the "synthetic" DOT 3 and 4 brake fluids)? It doesn't mix
with the DOT 3 and 4, as I understand it. I don't think
there's much reason to use other than DOT 3 and 4. Googling
for {"Brake fluid" silicone "DOT 3"} etc. turns up a lot.
E.g. see http://www.afcoracing.com/tech_pages/fluid.shtml
Let the group know how it goes... :-) I found it a little
tricky the first time but the second time was a breeze, like
I said, though I hope to improve on the rear brakes' bleed
part.
#30
Guest
Posts: n/a
Re: Brake Flush Bleeder Bolt Adapters?
"Mike Doyle" <sigifrith@frontiernet.net> wrote
> Elle wrote:
>> ...I did a brake flush yesterday, by myself for the
>> second time, on my 91 Civic LX (176k miles). I use the
>> Mity-Vac system ( a hand-held vacuum pump, connecting to
>> a small container to collect fluid, tubing, and
>> adapters).
>
> Hi Elle. No answers, but a few ? Where is a good source
> to
> buy the Mity-Vac?
The Mity-Vac (metal pump) kit I bought for around $40 is the
following:
http://www.harborfreight.com/cpi/cta...temnumber=2068
It's on sale for about $40 now. Take a printout of the site
above with you to the store to get the sale price.
Harbor Freight also sells a plastic pump version for around
$32. It is probably just fine.
From googling more on this, a lot of people have had "one
person brake bleed/flush" success with "Speed Bleeder
valves." One removes the old bleeder bolts and installs
these in their place. See site www.speedbleeder.com . Pep
Boys sells these one way (= check) valves, too.
>> I am thinking of buying a set of those one-way (that is,
>> check) bleeder valves that Pep Boys, for one, sells, to
>> (1) maybe get a better fit from adapter to valve; and (2)
>> minimize air introduction into the rear brake system.
>
> I'm getting ready to do a flush. Any trouble getting the
> bleeders off?
No, though if it's been awhile, I'd spray down the threads
as best I could with the penetrating oil "PB Blaster"
(around $4 for a big spray can). Great stuff.
I think I have read of people overtorquing and so breaking
these tiny bolts, though. Only 7 ft-lbs. is specified in the
manual for my 91 Civic.
> I don't know when mine were last touched,
> & hope they don't cause trouble.
>
>
> .... I used a 32 oz ( = two pints) container of Valvoline
>> "exceeds DOT 3 and 4 requirements" brake fluid for the
>> flush.
>
> I plan on using Motul Dot 5.1 fluid. Anyone have any
> comments on this?
Isn't that silicone brake fluid (to be distinguished from
the "synthetic" DOT 3 and 4 brake fluids)? It doesn't mix
with the DOT 3 and 4, as I understand it. I don't think
there's much reason to use other than DOT 3 and 4. Googling
for {"Brake fluid" silicone "DOT 3"} etc. turns up a lot.
E.g. see http://www.afcoracing.com/tech_pages/fluid.shtml
Let the group know how it goes... :-) I found it a little
tricky the first time but the second time was a breeze, like
I said, though I hope to improve on the rear brakes' bleed
part.
> Elle wrote:
>> ...I did a brake flush yesterday, by myself for the
>> second time, on my 91 Civic LX (176k miles). I use the
>> Mity-Vac system ( a hand-held vacuum pump, connecting to
>> a small container to collect fluid, tubing, and
>> adapters).
>
> Hi Elle. No answers, but a few ? Where is a good source
> to
> buy the Mity-Vac?
The Mity-Vac (metal pump) kit I bought for around $40 is the
following:
http://www.harborfreight.com/cpi/cta...temnumber=2068
It's on sale for about $40 now. Take a printout of the site
above with you to the store to get the sale price.
Harbor Freight also sells a plastic pump version for around
$32. It is probably just fine.
From googling more on this, a lot of people have had "one
person brake bleed/flush" success with "Speed Bleeder
valves." One removes the old bleeder bolts and installs
these in their place. See site www.speedbleeder.com . Pep
Boys sells these one way (= check) valves, too.
>> I am thinking of buying a set of those one-way (that is,
>> check) bleeder valves that Pep Boys, for one, sells, to
>> (1) maybe get a better fit from adapter to valve; and (2)
>> minimize air introduction into the rear brake system.
>
> I'm getting ready to do a flush. Any trouble getting the
> bleeders off?
No, though if it's been awhile, I'd spray down the threads
as best I could with the penetrating oil "PB Blaster"
(around $4 for a big spray can). Great stuff.
I think I have read of people overtorquing and so breaking
these tiny bolts, though. Only 7 ft-lbs. is specified in the
manual for my 91 Civic.
> I don't know when mine were last touched,
> & hope they don't cause trouble.
>
>
> .... I used a 32 oz ( = two pints) container of Valvoline
>> "exceeds DOT 3 and 4 requirements" brake fluid for the
>> flush.
>
> I plan on using Motul Dot 5.1 fluid. Anyone have any
> comments on this?
Isn't that silicone brake fluid (to be distinguished from
the "synthetic" DOT 3 and 4 brake fluids)? It doesn't mix
with the DOT 3 and 4, as I understand it. I don't think
there's much reason to use other than DOT 3 and 4. Googling
for {"Brake fluid" silicone "DOT 3"} etc. turns up a lot.
E.g. see http://www.afcoracing.com/tech_pages/fluid.shtml
Let the group know how it goes... :-) I found it a little
tricky the first time but the second time was a breeze, like
I said, though I hope to improve on the rear brakes' bleed
part.