Putting tension on 98 Civic belts
11-05-2003, 07:28 AM
#1
Guest
Posts: n/a
Putting tension on 98 Civic belts
Anybody have any tricks to putting tension on belts in a 98 Civic? The
components (alternator) seems to "float" on a relatively 3 inch straight
track, with a bolt to fasten the component in place, thus placing tension
on the belt.
Seems like their is about a 2 inch gap between the component and the engine
block. Not sure if using a wrecking bar as a lever would work, as this gap
seems too large for it.
All advice cheerfully appreciated!
components (alternator) seems to "float" on a relatively 3 inch straight
track, with a bolt to fasten the component in place, thus placing tension
on the belt.
Seems like their is about a 2 inch gap between the component and the engine
block. Not sure if using a wrecking bar as a lever would work, as this gap
seems too large for it.
All advice cheerfully appreciated!
11-05-2003, 11:36 AM
#2
Guest
Posts: n/a
Re: Putting tension on 98 Civic belts
I use a small crowbar usually.
"Herb" <chrisandsonya@bellsouth.net> wrote in message
news:Xns942A4C5314577chrisandsonyabellsou@216.77.1 88.17...
> Anybody have any tricks to putting tension on belts in a 98 Civic? The
> components (alternator) seems to "float" on a relatively 3 inch straight
> track, with a bolt to fasten the component in place, thus placing tension
> on the belt.
>
> Seems like their is about a 2 inch gap between the component and the
engine
> block. Not sure if using a wrecking bar as a lever would work, as this
gap
> seems too large for it.
>
> All advice cheerfully appreciated!
"Herb" <chrisandsonya@bellsouth.net> wrote in message
news:Xns942A4C5314577chrisandsonyabellsou@216.77.1 88.17...
> Anybody have any tricks to putting tension on belts in a 98 Civic? The
> components (alternator) seems to "float" on a relatively 3 inch straight
> track, with a bolt to fasten the component in place, thus placing tension
> on the belt.
>
> Seems like their is about a 2 inch gap between the component and the
engine
> block. Not sure if using a wrecking bar as a lever would work, as this
gap
> seems too large for it.
>
> All advice cheerfully appreciated!
11-05-2003, 11:36 AM
#3
Guest
Posts: n/a
Re: Putting tension on 98 Civic belts
I use a small crowbar usually.
"Herb" <chrisandsonya@bellsouth.net> wrote in message
news:Xns942A4C5314577chrisandsonyabellsou@216.77.1 88.17...
> Anybody have any tricks to putting tension on belts in a 98 Civic? The
> components (alternator) seems to "float" on a relatively 3 inch straight
> track, with a bolt to fasten the component in place, thus placing tension
> on the belt.
>
> Seems like their is about a 2 inch gap between the component and the
engine
> block. Not sure if using a wrecking bar as a lever would work, as this
gap
> seems too large for it.
>
> All advice cheerfully appreciated!
"Herb" <chrisandsonya@bellsouth.net> wrote in message
news:Xns942A4C5314577chrisandsonyabellsou@216.77.1 88.17...
> Anybody have any tricks to putting tension on belts in a 98 Civic? The
> components (alternator) seems to "float" on a relatively 3 inch straight
> track, with a bolt to fasten the component in place, thus placing tension
> on the belt.
>
> Seems like their is about a 2 inch gap between the component and the
engine
> block. Not sure if using a wrecking bar as a lever would work, as this
gap
> seems too large for it.
>
> All advice cheerfully appreciated!
11-05-2003, 11:36 AM
#4
Guest
Posts: n/a
Re: Putting tension on 98 Civic belts
I use a small crowbar usually.
"Herb" <chrisandsonya@bellsouth.net> wrote in message
news:Xns942A4C5314577chrisandsonyabellsou@216.77.1 88.17...
> Anybody have any tricks to putting tension on belts in a 98 Civic? The
> components (alternator) seems to "float" on a relatively 3 inch straight
> track, with a bolt to fasten the component in place, thus placing tension
> on the belt.
>
> Seems like their is about a 2 inch gap between the component and the
engine
> block. Not sure if using a wrecking bar as a lever would work, as this
gap
> seems too large for it.
>
> All advice cheerfully appreciated!
"Herb" <chrisandsonya@bellsouth.net> wrote in message
news:Xns942A4C5314577chrisandsonyabellsou@216.77.1 88.17...
> Anybody have any tricks to putting tension on belts in a 98 Civic? The
> components (alternator) seems to "float" on a relatively 3 inch straight
> track, with a bolt to fasten the component in place, thus placing tension
> on the belt.
>
> Seems like their is about a 2 inch gap between the component and the
engine
> block. Not sure if using a wrecking bar as a lever would work, as this
gap
> seems too large for it.
>
> All advice cheerfully appreciated!
11-05-2003, 11:36 AM
#5
Guest
Posts: n/a
Re: Putting tension on 98 Civic belts
I use a small crowbar usually.
"Herb" <chrisandsonya@bellsouth.net> wrote in message
news:Xns942A4C5314577chrisandsonyabellsou@216.77.1 88.17...
> Anybody have any tricks to putting tension on belts in a 98 Civic? The
> components (alternator) seems to "float" on a relatively 3 inch straight
> track, with a bolt to fasten the component in place, thus placing tension
> on the belt.
>
> Seems like their is about a 2 inch gap between the component and the
engine
> block. Not sure if using a wrecking bar as a lever would work, as this
gap
> seems too large for it.
>
> All advice cheerfully appreciated!
"Herb" <chrisandsonya@bellsouth.net> wrote in message
news:Xns942A4C5314577chrisandsonyabellsou@216.77.1 88.17...
> Anybody have any tricks to putting tension on belts in a 98 Civic? The
> components (alternator) seems to "float" on a relatively 3 inch straight
> track, with a bolt to fasten the component in place, thus placing tension
> on the belt.
>
> Seems like their is about a 2 inch gap between the component and the
engine
> block. Not sure if using a wrecking bar as a lever would work, as this
gap
> seems too large for it.
>
> All advice cheerfully appreciated!
Thread
Thread Starter
Forum
Replies
Last Post
2000civic customnblue17
Honda Civic - Del Sol - CRX
1
05-14-2008 05:18 PM
craigGy_T
honda / acura
2
05-05-2008 08:27 PM
nick d
honda / acura
2
11-16-2007 03:03 PM
ndccpf1
Honda Mailing List
1
11-15-2007 12:42 AM
kyriian
Car Parts For Sale
3
06-28-2006 12:42 AM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
