Replaced Timing Belt but . . .
06-16-2007, 10:47 AM
#1
Guest
Posts: n/a
Replaced Timing Belt but . . .
Am now wondering what all the fuss was about.
To backtrack, I have been reading this newsgroup off and on for the last few
years. I've seen many posts here warning of the importance of changing your
Honda Accord's timing belt at 75,000 miles or 7 years (or whatever the
interval is) or dire consequences will occur.
Long story short, I delayed replacing it for well beyond this replacement
interval but finally replaced both the timing belt and water pump on my 1994
Honda Accord with 98,000 miles on it. I am the original owner and the
timing belt had never been replaced before.
I told the shop to keep the old parts so I could see what they looked like,
expecting their condition to be terrible based on posts I have read here.
When I picked up the vehicle, they had placed the old timing belt and water
pump in a plastic bag for me. The timing belt was a small all-rubber belt
with teeth on it which went all the way around. I carefully inspected this
13 year old timing belt and it looked almost brand new! No cuts, nicks,
gouges, discoloration or any other noticeable wear! It looked fine, like it
didn't really need to be replaced. Not at all what I expected it to look
like.
I'm not saying I wish I didn't have it replaced. It gives me peace of mind
to have done so and if you guys say it's important, well you know alot more
about this stuff than I do. Just saying it didn't look at all like it
needed to be replaced.
Is stretching of the belt over time, which I probably would not be able to
notice, the issue affecting an old timing belt?
Anyway, just not what I expected to see.
To backtrack, I have been reading this newsgroup off and on for the last few
years. I've seen many posts here warning of the importance of changing your
Honda Accord's timing belt at 75,000 miles or 7 years (or whatever the
interval is) or dire consequences will occur.
Long story short, I delayed replacing it for well beyond this replacement
interval but finally replaced both the timing belt and water pump on my 1994
Honda Accord with 98,000 miles on it. I am the original owner and the
timing belt had never been replaced before.
I told the shop to keep the old parts so I could see what they looked like,
expecting their condition to be terrible based on posts I have read here.
When I picked up the vehicle, they had placed the old timing belt and water
pump in a plastic bag for me. The timing belt was a small all-rubber belt
with teeth on it which went all the way around. I carefully inspected this
13 year old timing belt and it looked almost brand new! No cuts, nicks,
gouges, discoloration or any other noticeable wear! It looked fine, like it
didn't really need to be replaced. Not at all what I expected it to look
like.
I'm not saying I wish I didn't have it replaced. It gives me peace of mind
to have done so and if you guys say it's important, well you know alot more
about this stuff than I do. Just saying it didn't look at all like it
needed to be replaced.
Is stretching of the belt over time, which I probably would not be able to
notice, the issue affecting an old timing belt?
Anyway, just not what I expected to see.
06-16-2007, 12:55 PM
#2
Guest
Posts: n/a
Re: Replaced Timing Belt but . . .
"Trident" <aaa@bbb.com> wrote in message
news:0_WdnSy_qadVZe7bnZ2dneKdnZydnZ2d@comcast.com. ..
> Am now wondering what all the fuss was about.
>
> To backtrack, I have been reading this newsgroup off and on for the last
> few
> years. I've seen many posts here warning of the importance of changing
> your
> Honda Accord's timing belt at 75,000 miles or 7 years (or whatever the
> interval is) or dire consequences will occur.
>
> Long story short, I delayed replacing it for well beyond this replacement
> interval but finally replaced both the timing belt and water pump on my
> 1994
> Honda Accord with 98,000 miles on it. I am the original owner and the
> timing belt had never been replaced before.
>
> I told the shop to keep the old parts so I could see what they looked
> like,
> expecting their condition to be terrible based on posts I have read here.
>
> When I picked up the vehicle, they had placed the old timing belt and
> water
> pump in a plastic bag for me. The timing belt was a small all-rubber belt
> with teeth on it which went all the way around. I carefully inspected
> this
> 13 year old timing belt and it looked almost brand new! No cuts, nicks,
> gouges, discoloration or any other noticeable wear! It looked fine, like
> it
> didn't really need to be replaced. Not at all what I expected it to look
> like.
>
> I'm not saying I wish I didn't have it replaced. It gives me peace of
> mind
> to have done so and if you guys say it's important, well you know alot
> more
> about this stuff than I do. Just saying it didn't look at all like it
> needed to be replaced.
>
> Is stretching of the belt over time, which I probably would not be able to
> notice, the issue affecting an old timing belt?
>
> Anyway, just not what I expected to see.
>
>
>
>
>
>
A timing belt ready to fail looks very much like a new one, but usually
dustier and a little scuffed on the backside where it rolls against the
tensioner. The failure typically occurs where the teeth attach to the belt.
On a new belt the teeth are firmly attached. By the time it's ready to be
replaced the teeth can be picked off with a knife blade. I'd expect yours to
be in that condition. By the time I replaced the belt on our old Volvo - a
non-interference engine - at about 150K miles the teeth could be picked off
with a thumbnail. Although the belt is often referred to as "breaking" I've
never personally seen one fail that way. They don't stretch measureably.
Timing chains are said to stretch, but as with bicycle chains it is really
that the pivots wear and the slack makes the overall chain longer.
That lack of visible change in the timing belt is why they are replaced on
schedule rather than on visual inspection. There is no reliable visible
warning of impending failure.
Mike
news:0_WdnSy_qadVZe7bnZ2dneKdnZydnZ2d@comcast.com. ..
> Am now wondering what all the fuss was about.
>
> To backtrack, I have been reading this newsgroup off and on for the last
> few
> years. I've seen many posts here warning of the importance of changing
> your
> Honda Accord's timing belt at 75,000 miles or 7 years (or whatever the
> interval is) or dire consequences will occur.
>
> Long story short, I delayed replacing it for well beyond this replacement
> interval but finally replaced both the timing belt and water pump on my
> 1994
> Honda Accord with 98,000 miles on it. I am the original owner and the
> timing belt had never been replaced before.
>
> I told the shop to keep the old parts so I could see what they looked
> like,
> expecting their condition to be terrible based on posts I have read here.
>
> When I picked up the vehicle, they had placed the old timing belt and
> water
> pump in a plastic bag for me. The timing belt was a small all-rubber belt
> with teeth on it which went all the way around. I carefully inspected
> this
> 13 year old timing belt and it looked almost brand new! No cuts, nicks,
> gouges, discoloration or any other noticeable wear! It looked fine, like
> it
> didn't really need to be replaced. Not at all what I expected it to look
> like.
>
> I'm not saying I wish I didn't have it replaced. It gives me peace of
> mind
> to have done so and if you guys say it's important, well you know alot
> more
> about this stuff than I do. Just saying it didn't look at all like it
> needed to be replaced.
>
> Is stretching of the belt over time, which I probably would not be able to
> notice, the issue affecting an old timing belt?
>
> Anyway, just not what I expected to see.
>
>
>
>
>
>
A timing belt ready to fail looks very much like a new one, but usually
dustier and a little scuffed on the backside where it rolls against the
tensioner. The failure typically occurs where the teeth attach to the belt.
On a new belt the teeth are firmly attached. By the time it's ready to be
replaced the teeth can be picked off with a knife blade. I'd expect yours to
be in that condition. By the time I replaced the belt on our old Volvo - a
non-interference engine - at about 150K miles the teeth could be picked off
with a thumbnail. Although the belt is often referred to as "breaking" I've
never personally seen one fail that way. They don't stretch measureably.
Timing chains are said to stretch, but as with bicycle chains it is really
that the pivots wear and the slack makes the overall chain longer.
That lack of visible change in the timing belt is why they are replaced on
schedule rather than on visual inspection. There is no reliable visible
warning of impending failure.
Mike
06-16-2007, 12:55 PM
#3
Guest
Posts: n/a
Re: Replaced Timing Belt but . . .
"Trident" <aaa@bbb.com> wrote in message
news:0_WdnSy_qadVZe7bnZ2dneKdnZydnZ2d@comcast.com. ..
> Am now wondering what all the fuss was about.
>
> To backtrack, I have been reading this newsgroup off and on for the last
> few
> years. I've seen many posts here warning of the importance of changing
> your
> Honda Accord's timing belt at 75,000 miles or 7 years (or whatever the
> interval is) or dire consequences will occur.
>
> Long story short, I delayed replacing it for well beyond this replacement
> interval but finally replaced both the timing belt and water pump on my
> 1994
> Honda Accord with 98,000 miles on it. I am the original owner and the
> timing belt had never been replaced before.
>
> I told the shop to keep the old parts so I could see what they looked
> like,
> expecting their condition to be terrible based on posts I have read here.
>
> When I picked up the vehicle, they had placed the old timing belt and
> water
> pump in a plastic bag for me. The timing belt was a small all-rubber belt
> with teeth on it which went all the way around. I carefully inspected
> this
> 13 year old timing belt and it looked almost brand new! No cuts, nicks,
> gouges, discoloration or any other noticeable wear! It looked fine, like
> it
> didn't really need to be replaced. Not at all what I expected it to look
> like.
>
> I'm not saying I wish I didn't have it replaced. It gives me peace of
> mind
> to have done so and if you guys say it's important, well you know alot
> more
> about this stuff than I do. Just saying it didn't look at all like it
> needed to be replaced.
>
> Is stretching of the belt over time, which I probably would not be able to
> notice, the issue affecting an old timing belt?
>
> Anyway, just not what I expected to see.
>
>
>
>
>
>
A timing belt ready to fail looks very much like a new one, but usually
dustier and a little scuffed on the backside where it rolls against the
tensioner. The failure typically occurs where the teeth attach to the belt.
On a new belt the teeth are firmly attached. By the time it's ready to be
replaced the teeth can be picked off with a knife blade. I'd expect yours to
be in that condition. By the time I replaced the belt on our old Volvo - a
non-interference engine - at about 150K miles the teeth could be picked off
with a thumbnail. Although the belt is often referred to as "breaking" I've
never personally seen one fail that way. They don't stretch measureably.
Timing chains are said to stretch, but as with bicycle chains it is really
that the pivots wear and the slack makes the overall chain longer.
That lack of visible change in the timing belt is why they are replaced on
schedule rather than on visual inspection. There is no reliable visible
warning of impending failure.
Mike
news:0_WdnSy_qadVZe7bnZ2dneKdnZydnZ2d@comcast.com. ..
> Am now wondering what all the fuss was about.
>
> To backtrack, I have been reading this newsgroup off and on for the last
> few
> years. I've seen many posts here warning of the importance of changing
> your
> Honda Accord's timing belt at 75,000 miles or 7 years (or whatever the
> interval is) or dire consequences will occur.
>
> Long story short, I delayed replacing it for well beyond this replacement
> interval but finally replaced both the timing belt and water pump on my
> 1994
> Honda Accord with 98,000 miles on it. I am the original owner and the
> timing belt had never been replaced before.
>
> I told the shop to keep the old parts so I could see what they looked
> like,
> expecting their condition to be terrible based on posts I have read here.
>
> When I picked up the vehicle, they had placed the old timing belt and
> water
> pump in a plastic bag for me. The timing belt was a small all-rubber belt
> with teeth on it which went all the way around. I carefully inspected
> this
> 13 year old timing belt and it looked almost brand new! No cuts, nicks,
> gouges, discoloration or any other noticeable wear! It looked fine, like
> it
> didn't really need to be replaced. Not at all what I expected it to look
> like.
>
> I'm not saying I wish I didn't have it replaced. It gives me peace of
> mind
> to have done so and if you guys say it's important, well you know alot
> more
> about this stuff than I do. Just saying it didn't look at all like it
> needed to be replaced.
>
> Is stretching of the belt over time, which I probably would not be able to
> notice, the issue affecting an old timing belt?
>
> Anyway, just not what I expected to see.
>
>
>
>
>
>
A timing belt ready to fail looks very much like a new one, but usually
dustier and a little scuffed on the backside where it rolls against the
tensioner. The failure typically occurs where the teeth attach to the belt.
On a new belt the teeth are firmly attached. By the time it's ready to be
replaced the teeth can be picked off with a knife blade. I'd expect yours to
be in that condition. By the time I replaced the belt on our old Volvo - a
non-interference engine - at about 150K miles the teeth could be picked off
with a thumbnail. Although the belt is often referred to as "breaking" I've
never personally seen one fail that way. They don't stretch measureably.
Timing chains are said to stretch, but as with bicycle chains it is really
that the pivots wear and the slack makes the overall chain longer.
That lack of visible change in the timing belt is why they are replaced on
schedule rather than on visual inspection. There is no reliable visible
warning of impending failure.
Mike
06-16-2007, 12:55 PM
#4
Guest
Posts: n/a
Re: Replaced Timing Belt but . . .
"Trident" <aaa@bbb.com> wrote in message
news:0_WdnSy_qadVZe7bnZ2dneKdnZydnZ2d@comcast.com. ..
> Am now wondering what all the fuss was about.
>
> To backtrack, I have been reading this newsgroup off and on for the last
> few
> years. I've seen many posts here warning of the importance of changing
> your
> Honda Accord's timing belt at 75,000 miles or 7 years (or whatever the
> interval is) or dire consequences will occur.
>
> Long story short, I delayed replacing it for well beyond this replacement
> interval but finally replaced both the timing belt and water pump on my
> 1994
> Honda Accord with 98,000 miles on it. I am the original owner and the
> timing belt had never been replaced before.
>
> I told the shop to keep the old parts so I could see what they looked
> like,
> expecting their condition to be terrible based on posts I have read here.
>
> When I picked up the vehicle, they had placed the old timing belt and
> water
> pump in a plastic bag for me. The timing belt was a small all-rubber belt
> with teeth on it which went all the way around. I carefully inspected
> this
> 13 year old timing belt and it looked almost brand new! No cuts, nicks,
> gouges, discoloration or any other noticeable wear! It looked fine, like
> it
> didn't really need to be replaced. Not at all what I expected it to look
> like.
>
> I'm not saying I wish I didn't have it replaced. It gives me peace of
> mind
> to have done so and if you guys say it's important, well you know alot
> more
> about this stuff than I do. Just saying it didn't look at all like it
> needed to be replaced.
>
> Is stretching of the belt over time, which I probably would not be able to
> notice, the issue affecting an old timing belt?
>
> Anyway, just not what I expected to see.
>
>
>
>
>
>
A timing belt ready to fail looks very much like a new one, but usually
dustier and a little scuffed on the backside where it rolls against the
tensioner. The failure typically occurs where the teeth attach to the belt.
On a new belt the teeth are firmly attached. By the time it's ready to be
replaced the teeth can be picked off with a knife blade. I'd expect yours to
be in that condition. By the time I replaced the belt on our old Volvo - a
non-interference engine - at about 150K miles the teeth could be picked off
with a thumbnail. Although the belt is often referred to as "breaking" I've
never personally seen one fail that way. They don't stretch measureably.
Timing chains are said to stretch, but as with bicycle chains it is really
that the pivots wear and the slack makes the overall chain longer.
That lack of visible change in the timing belt is why they are replaced on
schedule rather than on visual inspection. There is no reliable visible
warning of impending failure.
Mike
news:0_WdnSy_qadVZe7bnZ2dneKdnZydnZ2d@comcast.com. ..
> Am now wondering what all the fuss was about.
>
> To backtrack, I have been reading this newsgroup off and on for the last
> few
> years. I've seen many posts here warning of the importance of changing
> your
> Honda Accord's timing belt at 75,000 miles or 7 years (or whatever the
> interval is) or dire consequences will occur.
>
> Long story short, I delayed replacing it for well beyond this replacement
> interval but finally replaced both the timing belt and water pump on my
> 1994
> Honda Accord with 98,000 miles on it. I am the original owner and the
> timing belt had never been replaced before.
>
> I told the shop to keep the old parts so I could see what they looked
> like,
> expecting their condition to be terrible based on posts I have read here.
>
> When I picked up the vehicle, they had placed the old timing belt and
> water
> pump in a plastic bag for me. The timing belt was a small all-rubber belt
> with teeth on it which went all the way around. I carefully inspected
> this
> 13 year old timing belt and it looked almost brand new! No cuts, nicks,
> gouges, discoloration or any other noticeable wear! It looked fine, like
> it
> didn't really need to be replaced. Not at all what I expected it to look
> like.
>
> I'm not saying I wish I didn't have it replaced. It gives me peace of
> mind
> to have done so and if you guys say it's important, well you know alot
> more
> about this stuff than I do. Just saying it didn't look at all like it
> needed to be replaced.
>
> Is stretching of the belt over time, which I probably would not be able to
> notice, the issue affecting an old timing belt?
>
> Anyway, just not what I expected to see.
>
>
>
>
>
>
A timing belt ready to fail looks very much like a new one, but usually
dustier and a little scuffed on the backside where it rolls against the
tensioner. The failure typically occurs where the teeth attach to the belt.
On a new belt the teeth are firmly attached. By the time it's ready to be
replaced the teeth can be picked off with a knife blade. I'd expect yours to
be in that condition. By the time I replaced the belt on our old Volvo - a
non-interference engine - at about 150K miles the teeth could be picked off
with a thumbnail. Although the belt is often referred to as "breaking" I've
never personally seen one fail that way. They don't stretch measureably.
Timing chains are said to stretch, but as with bicycle chains it is really
that the pivots wear and the slack makes the overall chain longer.
That lack of visible change in the timing belt is why they are replaced on
schedule rather than on visual inspection. There is no reliable visible
warning of impending failure.
Mike
06-16-2007, 01:42 PM
#5
Guest
Posts: n/a
Re: Replaced Timing Belt but . . .
"Trident" <aaa@bbb.com> wrote in
news:0_WdnSy_qadVZe7bnZ2dneKdnZydnZ2d@comcast.com:
> Am now wondering what all the fuss was about.
>
> To backtrack, I have been reading this newsgroup off and on for the
> last few years. I've seen many posts here warning of the importance
> of changing your Honda Accord's timing belt at 75,000 miles or 7 years
> (or whatever the interval is) or dire consequences will occur.
>
> Long story short, I delayed replacing it for well beyond this
> replacement interval but finally replaced both the timing belt and
> water pump on my 1994 Honda Accord with 98,000 miles on it. I am the
> original owner and the timing belt had never been replaced before.
>
> I told the shop to keep the old parts so I could see what they looked
> like, expecting their condition to be terrible based on posts I have
> read here.
>
> When I picked up the vehicle, they had placed the old timing belt and
> water pump in a plastic bag for me. The timing belt was a small
> all-rubber belt with teeth on it which went all the way around.
It's not "all rubber". It has a fabric carcass that extends even into
the teeth. The carcass provides the belt with all its strength.
> I
> carefully inspected this 13 year old timing belt and it looked almost
> brand new! No cuts, nicks, gouges, discoloration or any other
> noticeable wear! It looked fine,
Wear manifests as deterioration of the fabric carcass. You cannot see
that wear with your eyes.
You have no idea when the carcass has weakened to the point of failure
until the weave separates and the belt breaks or the teeth strip off.
> like it didn't really need to be
> replaced. Not at all what I expected it to look like.
>
> I'm not saying I wish I didn't have it replaced. It gives me peace of
> mind to have done so and if you guys say it's important, well you know
> alot more about this stuff than I do. Just saying it didn't look at
> all like it needed to be replaced.
They never do.
>
> Is stretching of the belt over time, which I probably would not be
> able to notice, the issue affecting an old timing belt?
See above.
--
Tegger
The Unofficial Honda/Acura FAQ
www.tegger.com/hondafaq/
news:0_WdnSy_qadVZe7bnZ2dneKdnZydnZ2d@comcast.com:
> Am now wondering what all the fuss was about.
>
> To backtrack, I have been reading this newsgroup off and on for the
> last few years. I've seen many posts here warning of the importance
> of changing your Honda Accord's timing belt at 75,000 miles or 7 years
> (or whatever the interval is) or dire consequences will occur.
>
> Long story short, I delayed replacing it for well beyond this
> replacement interval but finally replaced both the timing belt and
> water pump on my 1994 Honda Accord with 98,000 miles on it. I am the
> original owner and the timing belt had never been replaced before.
>
> I told the shop to keep the old parts so I could see what they looked
> like, expecting their condition to be terrible based on posts I have
> read here.
>
> When I picked up the vehicle, they had placed the old timing belt and
> water pump in a plastic bag for me. The timing belt was a small
> all-rubber belt with teeth on it which went all the way around.
It's not "all rubber". It has a fabric carcass that extends even into
the teeth. The carcass provides the belt with all its strength.
> I
> carefully inspected this 13 year old timing belt and it looked almost
> brand new! No cuts, nicks, gouges, discoloration or any other
> noticeable wear! It looked fine,
Wear manifests as deterioration of the fabric carcass. You cannot see
that wear with your eyes.
You have no idea when the carcass has weakened to the point of failure
until the weave separates and the belt breaks or the teeth strip off.
> like it didn't really need to be
> replaced. Not at all what I expected it to look like.
>
> I'm not saying I wish I didn't have it replaced. It gives me peace of
> mind to have done so and if you guys say it's important, well you know
> alot more about this stuff than I do. Just saying it didn't look at
> all like it needed to be replaced.
They never do.
>
> Is stretching of the belt over time, which I probably would not be
> able to notice, the issue affecting an old timing belt?
See above.
--
Tegger
The Unofficial Honda/Acura FAQ
www.tegger.com/hondafaq/
06-16-2007, 01:42 PM
#6
Guest
Posts: n/a
Re: Replaced Timing Belt but . . .
"Trident" <aaa@bbb.com> wrote in
news:0_WdnSy_qadVZe7bnZ2dneKdnZydnZ2d@comcast.com:
> Am now wondering what all the fuss was about.
>
> To backtrack, I have been reading this newsgroup off and on for the
> last few years. I've seen many posts here warning of the importance
> of changing your Honda Accord's timing belt at 75,000 miles or 7 years
> (or whatever the interval is) or dire consequences will occur.
>
> Long story short, I delayed replacing it for well beyond this
> replacement interval but finally replaced both the timing belt and
> water pump on my 1994 Honda Accord with 98,000 miles on it. I am the
> original owner and the timing belt had never been replaced before.
>
> I told the shop to keep the old parts so I could see what they looked
> like, expecting their condition to be terrible based on posts I have
> read here.
>
> When I picked up the vehicle, they had placed the old timing belt and
> water pump in a plastic bag for me. The timing belt was a small
> all-rubber belt with teeth on it which went all the way around.
It's not "all rubber". It has a fabric carcass that extends even into
the teeth. The carcass provides the belt with all its strength.
> I
> carefully inspected this 13 year old timing belt and it looked almost
> brand new! No cuts, nicks, gouges, discoloration or any other
> noticeable wear! It looked fine,
Wear manifests as deterioration of the fabric carcass. You cannot see
that wear with your eyes.
You have no idea when the carcass has weakened to the point of failure
until the weave separates and the belt breaks or the teeth strip off.
> like it didn't really need to be
> replaced. Not at all what I expected it to look like.
>
> I'm not saying I wish I didn't have it replaced. It gives me peace of
> mind to have done so and if you guys say it's important, well you know
> alot more about this stuff than I do. Just saying it didn't look at
> all like it needed to be replaced.
They never do.
>
> Is stretching of the belt over time, which I probably would not be
> able to notice, the issue affecting an old timing belt?
See above.
--
Tegger
The Unofficial Honda/Acura FAQ
www.tegger.com/hondafaq/
news:0_WdnSy_qadVZe7bnZ2dneKdnZydnZ2d@comcast.com:
> Am now wondering what all the fuss was about.
>
> To backtrack, I have been reading this newsgroup off and on for the
> last few years. I've seen many posts here warning of the importance
> of changing your Honda Accord's timing belt at 75,000 miles or 7 years
> (or whatever the interval is) or dire consequences will occur.
>
> Long story short, I delayed replacing it for well beyond this
> replacement interval but finally replaced both the timing belt and
> water pump on my 1994 Honda Accord with 98,000 miles on it. I am the
> original owner and the timing belt had never been replaced before.
>
> I told the shop to keep the old parts so I could see what they looked
> like, expecting their condition to be terrible based on posts I have
> read here.
>
> When I picked up the vehicle, they had placed the old timing belt and
> water pump in a plastic bag for me. The timing belt was a small
> all-rubber belt with teeth on it which went all the way around.
It's not "all rubber". It has a fabric carcass that extends even into
the teeth. The carcass provides the belt with all its strength.
> I
> carefully inspected this 13 year old timing belt and it looked almost
> brand new! No cuts, nicks, gouges, discoloration or any other
> noticeable wear! It looked fine,
Wear manifests as deterioration of the fabric carcass. You cannot see
that wear with your eyes.
You have no idea when the carcass has weakened to the point of failure
until the weave separates and the belt breaks or the teeth strip off.
> like it didn't really need to be
> replaced. Not at all what I expected it to look like.
>
> I'm not saying I wish I didn't have it replaced. It gives me peace of
> mind to have done so and if you guys say it's important, well you know
> alot more about this stuff than I do. Just saying it didn't look at
> all like it needed to be replaced.
They never do.
>
> Is stretching of the belt over time, which I probably would not be
> able to notice, the issue affecting an old timing belt?
See above.
--
Tegger
The Unofficial Honda/Acura FAQ
www.tegger.com/hondafaq/
06-16-2007, 01:42 PM
#7
Guest
Posts: n/a
Re: Replaced Timing Belt but . . .
"Trident" <aaa@bbb.com> wrote in
news:0_WdnSy_qadVZe7bnZ2dneKdnZydnZ2d@comcast.com:
> Am now wondering what all the fuss was about.
>
> To backtrack, I have been reading this newsgroup off and on for the
> last few years. I've seen many posts here warning of the importance
> of changing your Honda Accord's timing belt at 75,000 miles or 7 years
> (or whatever the interval is) or dire consequences will occur.
>
> Long story short, I delayed replacing it for well beyond this
> replacement interval but finally replaced both the timing belt and
> water pump on my 1994 Honda Accord with 98,000 miles on it. I am the
> original owner and the timing belt had never been replaced before.
>
> I told the shop to keep the old parts so I could see what they looked
> like, expecting their condition to be terrible based on posts I have
> read here.
>
> When I picked up the vehicle, they had placed the old timing belt and
> water pump in a plastic bag for me. The timing belt was a small
> all-rubber belt with teeth on it which went all the way around.
It's not "all rubber". It has a fabric carcass that extends even into
the teeth. The carcass provides the belt with all its strength.
> I
> carefully inspected this 13 year old timing belt and it looked almost
> brand new! No cuts, nicks, gouges, discoloration or any other
> noticeable wear! It looked fine,
Wear manifests as deterioration of the fabric carcass. You cannot see
that wear with your eyes.
You have no idea when the carcass has weakened to the point of failure
until the weave separates and the belt breaks or the teeth strip off.
> like it didn't really need to be
> replaced. Not at all what I expected it to look like.
>
> I'm not saying I wish I didn't have it replaced. It gives me peace of
> mind to have done so and if you guys say it's important, well you know
> alot more about this stuff than I do. Just saying it didn't look at
> all like it needed to be replaced.
They never do.
>
> Is stretching of the belt over time, which I probably would not be
> able to notice, the issue affecting an old timing belt?
See above.
--
Tegger
The Unofficial Honda/Acura FAQ
www.tegger.com/hondafaq/
news:0_WdnSy_qadVZe7bnZ2dneKdnZydnZ2d@comcast.com:
> Am now wondering what all the fuss was about.
>
> To backtrack, I have been reading this newsgroup off and on for the
> last few years. I've seen many posts here warning of the importance
> of changing your Honda Accord's timing belt at 75,000 miles or 7 years
> (or whatever the interval is) or dire consequences will occur.
>
> Long story short, I delayed replacing it for well beyond this
> replacement interval but finally replaced both the timing belt and
> water pump on my 1994 Honda Accord with 98,000 miles on it. I am the
> original owner and the timing belt had never been replaced before.
>
> I told the shop to keep the old parts so I could see what they looked
> like, expecting their condition to be terrible based on posts I have
> read here.
>
> When I picked up the vehicle, they had placed the old timing belt and
> water pump in a plastic bag for me. The timing belt was a small
> all-rubber belt with teeth on it which went all the way around.
It's not "all rubber". It has a fabric carcass that extends even into
the teeth. The carcass provides the belt with all its strength.
> I
> carefully inspected this 13 year old timing belt and it looked almost
> brand new! No cuts, nicks, gouges, discoloration or any other
> noticeable wear! It looked fine,
Wear manifests as deterioration of the fabric carcass. You cannot see
that wear with your eyes.
You have no idea when the carcass has weakened to the point of failure
until the weave separates and the belt breaks or the teeth strip off.
> like it didn't really need to be
> replaced. Not at all what I expected it to look like.
>
> I'm not saying I wish I didn't have it replaced. It gives me peace of
> mind to have done so and if you guys say it's important, well you know
> alot more about this stuff than I do. Just saying it didn't look at
> all like it needed to be replaced.
They never do.
>
> Is stretching of the belt over time, which I probably would not be
> able to notice, the issue affecting an old timing belt?
See above.
--
Tegger
The Unofficial Honda/Acura FAQ
www.tegger.com/hondafaq/
06-16-2007, 01:57 PM
#8
Guest
Posts: n/a
Re: Replaced Timing Belt but . . .
"Tegger" <tegger@tegger.c0m> wrote:
> It's not "all rubber". It has a fabric carcass that extends even into the
teeth. The carcass provides the belt with all its strength.
So is the fabric in the core of the timing belt surrounded by the rubber so
that it cannot be seen? I still have the old timing belt, and when I
inspect it carefully I cannot see fabric anywhere. I can see how the fabric
would provide added strength. Maybe I'll disect it and see exactly how the
fabric works.
Thanks.
> It's not "all rubber". It has a fabric carcass that extends even into the
teeth. The carcass provides the belt with all its strength.
So is the fabric in the core of the timing belt surrounded by the rubber so
that it cannot be seen? I still have the old timing belt, and when I
inspect it carefully I cannot see fabric anywhere. I can see how the fabric
would provide added strength. Maybe I'll disect it and see exactly how the
fabric works.
Thanks.
06-16-2007, 01:57 PM
#9
Guest
Posts: n/a
Re: Replaced Timing Belt but . . .
"Tegger" <tegger@tegger.c0m> wrote:
> It's not "all rubber". It has a fabric carcass that extends even into the
teeth. The carcass provides the belt with all its strength.
So is the fabric in the core of the timing belt surrounded by the rubber so
that it cannot be seen? I still have the old timing belt, and when I
inspect it carefully I cannot see fabric anywhere. I can see how the fabric
would provide added strength. Maybe I'll disect it and see exactly how the
fabric works.
Thanks.
> It's not "all rubber". It has a fabric carcass that extends even into the
teeth. The carcass provides the belt with all its strength.
So is the fabric in the core of the timing belt surrounded by the rubber so
that it cannot be seen? I still have the old timing belt, and when I
inspect it carefully I cannot see fabric anywhere. I can see how the fabric
would provide added strength. Maybe I'll disect it and see exactly how the
fabric works.
Thanks.
06-16-2007, 01:57 PM
#10
Guest
Posts: n/a
Re: Replaced Timing Belt but . . .
"Tegger" <tegger@tegger.c0m> wrote:
> It's not "all rubber". It has a fabric carcass that extends even into the
teeth. The carcass provides the belt with all its strength.
So is the fabric in the core of the timing belt surrounded by the rubber so
that it cannot be seen? I still have the old timing belt, and when I
inspect it carefully I cannot see fabric anywhere. I can see how the fabric
would provide added strength. Maybe I'll disect it and see exactly how the
fabric works.
Thanks.
> It's not "all rubber". It has a fabric carcass that extends even into the
teeth. The carcass provides the belt with all its strength.
So is the fabric in the core of the timing belt surrounded by the rubber so
that it cannot be seen? I still have the old timing belt, and when I
inspect it carefully I cannot see fabric anywhere. I can see how the fabric
would provide added strength. Maybe I'll disect it and see exactly how the
fabric works.
Thanks.
06-17-2007, 06:57 AM
#11
Guest
Posts: n/a
Re: Replaced Timing Belt but . . .
Michael Pardee wrote:
>
> A timing belt ready to fail looks very much like a new one, but usually
> dustier and a little scuffed on the backside where it rolls against the
> tensioner. The failure typically occurs where the teeth attach to the
> belt. On a new belt the teeth are firmly attached. By the time it's ready
> to be replaced the teeth can be picked off with a knife blade. I'd expect
> yours to be in that condition. By the time I replaced the belt on our old
> Volvo - a non-interference engine - at about 150K miles the teeth could be
> picked off with a thumbnail. Although the belt is often referred to as
> "breaking" I've never personally seen one fail that way. They don't
> stretch measureably.
I've seen a few stretch. This was typical of mid to late 80's Accords and
Preludes if I remember correctly. The belt would stretch and then the
distributor would start making a tapping noise. Retensioning the belt would
usually set things straight and quiet down the distributor.
Eric
>
> A timing belt ready to fail looks very much like a new one, but usually
> dustier and a little scuffed on the backside where it rolls against the
> tensioner. The failure typically occurs where the teeth attach to the
> belt. On a new belt the teeth are firmly attached. By the time it's ready
> to be replaced the teeth can be picked off with a knife blade. I'd expect
> yours to be in that condition. By the time I replaced the belt on our old
> Volvo - a non-interference engine - at about 150K miles the teeth could be
> picked off with a thumbnail. Although the belt is often referred to as
> "breaking" I've never personally seen one fail that way. They don't
> stretch measureably.
I've seen a few stretch. This was typical of mid to late 80's Accords and
Preludes if I remember correctly. The belt would stretch and then the
distributor would start making a tapping noise. Retensioning the belt would
usually set things straight and quiet down the distributor.
Eric
06-17-2007, 06:57 AM
#12
Guest
Posts: n/a
Re: Replaced Timing Belt but . . .
Michael Pardee wrote:
>
> A timing belt ready to fail looks very much like a new one, but usually
> dustier and a little scuffed on the backside where it rolls against the
> tensioner. The failure typically occurs where the teeth attach to the
> belt. On a new belt the teeth are firmly attached. By the time it's ready
> to be replaced the teeth can be picked off with a knife blade. I'd expect
> yours to be in that condition. By the time I replaced the belt on our old
> Volvo - a non-interference engine - at about 150K miles the teeth could be
> picked off with a thumbnail. Although the belt is often referred to as
> "breaking" I've never personally seen one fail that way. They don't
> stretch measureably.
I've seen a few stretch. This was typical of mid to late 80's Accords and
Preludes if I remember correctly. The belt would stretch and then the
distributor would start making a tapping noise. Retensioning the belt would
usually set things straight and quiet down the distributor.
Eric
>
> A timing belt ready to fail looks very much like a new one, but usually
> dustier and a little scuffed on the backside where it rolls against the
> tensioner. The failure typically occurs where the teeth attach to the
> belt. On a new belt the teeth are firmly attached. By the time it's ready
> to be replaced the teeth can be picked off with a knife blade. I'd expect
> yours to be in that condition. By the time I replaced the belt on our old
> Volvo - a non-interference engine - at about 150K miles the teeth could be
> picked off with a thumbnail. Although the belt is often referred to as
> "breaking" I've never personally seen one fail that way. They don't
> stretch measureably.
I've seen a few stretch. This was typical of mid to late 80's Accords and
Preludes if I remember correctly. The belt would stretch and then the
distributor would start making a tapping noise. Retensioning the belt would
usually set things straight and quiet down the distributor.
Eric
06-17-2007, 06:57 AM
#13
Guest
Posts: n/a
Re: Replaced Timing Belt but . . .
Michael Pardee wrote:
>
> A timing belt ready to fail looks very much like a new one, but usually
> dustier and a little scuffed on the backside where it rolls against the
> tensioner. The failure typically occurs where the teeth attach to the
> belt. On a new belt the teeth are firmly attached. By the time it's ready
> to be replaced the teeth can be picked off with a knife blade. I'd expect
> yours to be in that condition. By the time I replaced the belt on our old
> Volvo - a non-interference engine - at about 150K miles the teeth could be
> picked off with a thumbnail. Although the belt is often referred to as
> "breaking" I've never personally seen one fail that way. They don't
> stretch measureably.
I've seen a few stretch. This was typical of mid to late 80's Accords and
Preludes if I remember correctly. The belt would stretch and then the
distributor would start making a tapping noise. Retensioning the belt would
usually set things straight and quiet down the distributor.
Eric
>
> A timing belt ready to fail looks very much like a new one, but usually
> dustier and a little scuffed on the backside where it rolls against the
> tensioner. The failure typically occurs where the teeth attach to the
> belt. On a new belt the teeth are firmly attached. By the time it's ready
> to be replaced the teeth can be picked off with a knife blade. I'd expect
> yours to be in that condition. By the time I replaced the belt on our old
> Volvo - a non-interference engine - at about 150K miles the teeth could be
> picked off with a thumbnail. Although the belt is often referred to as
> "breaking" I've never personally seen one fail that way. They don't
> stretch measureably.
I've seen a few stretch. This was typical of mid to late 80's Accords and
Preludes if I remember correctly. The belt would stretch and then the
distributor would start making a tapping noise. Retensioning the belt would
usually set things straight and quiet down the distributor.
Eric
06-17-2007, 08:38 AM
#14
Guest
Posts: n/a
Re: Replaced Timing Belt but . . .
"Eric" <say.no@spam.now> wrote in message news:4675138D.D5FDFB01@spam.now...
> Michael Pardee wrote:
>>
>> A timing belt ready to fail looks very much like a new one, but usually
>> dustier and a little scuffed on the backside where it rolls against the
>> tensioner. The failure typically occurs where the teeth attach to the
>> belt. On a new belt the teeth are firmly attached. By the time it's ready
>> to be replaced the teeth can be picked off with a knife blade. I'd expect
>> yours to be in that condition. By the time I replaced the belt on our old
>> Volvo - a non-interference engine - at about 150K miles the teeth could
>> be
>> picked off with a thumbnail. Although the belt is often referred to as
>> "breaking" I've never personally seen one fail that way. They don't
>> stretch measureably.
>
> I've seen a few stretch. This was typical of mid to late 80's Accords and
> Preludes if I remember correctly. The belt would stretch and then the
> distributor would start making a tapping noise. Retensioning the belt
> would
> usually set things straight and quiet down the distributor.
>
> Eric
>
Interesting. Maybe a reinforcing fabric that has since been updated, I hope.
Mike
> Michael Pardee wrote:
>>
>> A timing belt ready to fail looks very much like a new one, but usually
>> dustier and a little scuffed on the backside where it rolls against the
>> tensioner. The failure typically occurs where the teeth attach to the
>> belt. On a new belt the teeth are firmly attached. By the time it's ready
>> to be replaced the teeth can be picked off with a knife blade. I'd expect
>> yours to be in that condition. By the time I replaced the belt on our old
>> Volvo - a non-interference engine - at about 150K miles the teeth could
>> be
>> picked off with a thumbnail. Although the belt is often referred to as
>> "breaking" I've never personally seen one fail that way. They don't
>> stretch measureably.
>
> I've seen a few stretch. This was typical of mid to late 80's Accords and
> Preludes if I remember correctly. The belt would stretch and then the
> distributor would start making a tapping noise. Retensioning the belt
> would
> usually set things straight and quiet down the distributor.
>
> Eric
>
Interesting. Maybe a reinforcing fabric that has since been updated, I hope.
Mike
06-17-2007, 08:38 AM
#15
Guest
Posts: n/a
Re: Replaced Timing Belt but . . .
"Eric" <say.no@spam.now> wrote in message news:4675138D.D5FDFB01@spam.now...
> Michael Pardee wrote:
>>
>> A timing belt ready to fail looks very much like a new one, but usually
>> dustier and a little scuffed on the backside where it rolls against the
>> tensioner. The failure typically occurs where the teeth attach to the
>> belt. On a new belt the teeth are firmly attached. By the time it's ready
>> to be replaced the teeth can be picked off with a knife blade. I'd expect
>> yours to be in that condition. By the time I replaced the belt on our old
>> Volvo - a non-interference engine - at about 150K miles the teeth could
>> be
>> picked off with a thumbnail. Although the belt is often referred to as
>> "breaking" I've never personally seen one fail that way. They don't
>> stretch measureably.
>
> I've seen a few stretch. This was typical of mid to late 80's Accords and
> Preludes if I remember correctly. The belt would stretch and then the
> distributor would start making a tapping noise. Retensioning the belt
> would
> usually set things straight and quiet down the distributor.
>
> Eric
>
Interesting. Maybe a reinforcing fabric that has since been updated, I hope.
Mike
> Michael Pardee wrote:
>>
>> A timing belt ready to fail looks very much like a new one, but usually
>> dustier and a little scuffed on the backside where it rolls against the
>> tensioner. The failure typically occurs where the teeth attach to the
>> belt. On a new belt the teeth are firmly attached. By the time it's ready
>> to be replaced the teeth can be picked off with a knife blade. I'd expect
>> yours to be in that condition. By the time I replaced the belt on our old
>> Volvo - a non-interference engine - at about 150K miles the teeth could
>> be
>> picked off with a thumbnail. Although the belt is often referred to as
>> "breaking" I've never personally seen one fail that way. They don't
>> stretch measureably.
>
> I've seen a few stretch. This was typical of mid to late 80's Accords and
> Preludes if I remember correctly. The belt would stretch and then the
> distributor would start making a tapping noise. Retensioning the belt
> would
> usually set things straight and quiet down the distributor.
>
> Eric
>
Interesting. Maybe a reinforcing fabric that has since been updated, I hope.
Mike
