99 Accent axel bearing question
#1
Guest
Posts: n/a
99 Accent axel bearing question
I've got a high pitched sqeak sometimes when the car is rolling.
Braking stops it. Since I just changes the front brakes for the
second time in 3 months I thought I had better check the rear. No
noise when wheels spin free and no feel like a bad bearing but the
rear drums are pretty rusted and stuck on. Used some WD40 and will
check the price of new drums later. Probably replace brakes and drums
as long as I have things apart. 80,000 on the car so it's probably
due. What I'm wondering about is the bearings. It appears they may
be sealed from the little I have read in the shop manual. Can they be
repacked or lubed in any way? If is makes sense I will do any
maintenance otherwise I am thinkng of replacing them because of the
squeak. Any thoughts would be appreciated.
nothermark
Braking stops it. Since I just changes the front brakes for the
second time in 3 months I thought I had better check the rear. No
noise when wheels spin free and no feel like a bad bearing but the
rear drums are pretty rusted and stuck on. Used some WD40 and will
check the price of new drums later. Probably replace brakes and drums
as long as I have things apart. 80,000 on the car so it's probably
due. What I'm wondering about is the bearings. It appears they may
be sealed from the little I have read in the shop manual. Can they be
repacked or lubed in any way? If is makes sense I will do any
maintenance otherwise I am thinkng of replacing them because of the
squeak. Any thoughts would be appreciated.
nothermark
#2
Guest
Posts: n/a
Re: 99 Accent axel bearing question
On Tue, 22 Mar 2005 22:22:33 GMT, nothermark <trash@gnomex.cotse.net>
wrote:
>I've got a high pitched sqeak sometimes when the car is rolling.
>Braking stops it. Since I just changes the front brakes for the
>second time in 3 months I thought I had better check the rear. No
>noise when wheels spin free and no feel like a bad bearing but the
>rear drums are pretty rusted and stuck on. Used some WD40 and will
>check the price of new drums later. Probably replace brakes and drums
>as long as I have things apart. 80,000 on the car so it's probably
>due. What I'm wondering about is the bearings. It appears they may
>be sealed from the little I have read in the shop manual. Can they be
>repacked or lubed in any way? If is makes sense I will do any
>maintenance otherwise I am thinkng of replacing them because of the
>squeak. Any thoughts would be appreciated.
>
>nothermark
Just checked Autozone -
Drums are $50 ea special order
can't buy bearings but new spindle sets complete are $82
so $300 plus brake parts...... guess I won't be in a hurry on this.
wrote:
>I've got a high pitched sqeak sometimes when the car is rolling.
>Braking stops it. Since I just changes the front brakes for the
>second time in 3 months I thought I had better check the rear. No
>noise when wheels spin free and no feel like a bad bearing but the
>rear drums are pretty rusted and stuck on. Used some WD40 and will
>check the price of new drums later. Probably replace brakes and drums
>as long as I have things apart. 80,000 on the car so it's probably
>due. What I'm wondering about is the bearings. It appears they may
>be sealed from the little I have read in the shop manual. Can they be
>repacked or lubed in any way? If is makes sense I will do any
>maintenance otherwise I am thinkng of replacing them because of the
>squeak. Any thoughts would be appreciated.
>
>nothermark
Just checked Autozone -
Drums are $50 ea special order
can't buy bearings but new spindle sets complete are $82
so $300 plus brake parts...... guess I won't be in a hurry on this.
#3
Guest
Posts: n/a
Re: 99 Accent axel bearing question
> >nothermark
>
> Just checked Autozone -
>
> Drums are $50 ea special order
> can't buy bearings but new spindle sets complete are $82
>
> so $300 plus brake parts...... guess I won't be in a hurry on this.
If you have not done a rear brake job yet I would imagine your drums
could be turned and re-used. They can be machined just like rotors to
restore the friction surface. My experience with autozone and brake
parts has been VERY poor. Albany brake linings are the worst you can
get in my opinion. Buy your friction parts at napa(united brand) or
checker/shucks/kragen(Raybestos).
Bearings on most cars now are 'sealed'. Usually the hub/bearings come
as one assembly that cannot be serviced. If you are not getting
abnormal noises(whining/growling sounds, spins rough by hand, etc) then
you do not need to replace anything.
>
> Just checked Autozone -
>
> Drums are $50 ea special order
> can't buy bearings but new spindle sets complete are $82
>
> so $300 plus brake parts...... guess I won't be in a hurry on this.
If you have not done a rear brake job yet I would imagine your drums
could be turned and re-used. They can be machined just like rotors to
restore the friction surface. My experience with autozone and brake
parts has been VERY poor. Albany brake linings are the worst you can
get in my opinion. Buy your friction parts at napa(united brand) or
checker/shucks/kragen(Raybestos).
Bearings on most cars now are 'sealed'. Usually the hub/bearings come
as one assembly that cannot be serviced. If you are not getting
abnormal noises(whining/growling sounds, spins rough by hand, etc) then
you do not need to replace anything.
#5
Guest
Posts: n/a
Re: 99 Accent axel bearing question
On Wed, 23 Mar 2005 19:38:41 -0500, "hyundaitech"
<notpublic@not.public.com> wrote:
>It's probably best to try to hunt down where the noise is originating.
>It's possible that the pad shims are making contact with the rotor. The
>fact that you've replaced pads twice in three months also bothers me.
The three month deal was the Autozone premium pads on the front. I
thought the extra $15 would get me pads that would last better :-(.
They exchanged them free but I went back to the cheaper pads that last
better. This summer I will replace the rotors - not a fun job on the
Hyundai. They are chewed up enough I will have problems with
inspection but the car stops fine.
The deal with the rear's is an intermittent high pitched sound that I
seems to be coming from the back end. I tried pulling the drum the
other day but it was rusted to the metal cover for the bearing. I
will get if off today or tomorrow and see what is going on. It may be
nothing more than a new pair of shoes.
The thing with Hyundai parts that is throwing me is the cost compared
to the Ford car and Chevy truck I also work on. When I can replace
drums for $20 ea it is cheap enough and easier than getting them
turned. At $50 it is not a good option. I will admit I have gotten
lazy in that it is much easier to throw $100 worth of parts into
something and be done rather than to figure out what $100 part out of
several is the real problem. ;-)
<notpublic@not.public.com> wrote:
>It's probably best to try to hunt down where the noise is originating.
>It's possible that the pad shims are making contact with the rotor. The
>fact that you've replaced pads twice in three months also bothers me.
The three month deal was the Autozone premium pads on the front. I
thought the extra $15 would get me pads that would last better :-(.
They exchanged them free but I went back to the cheaper pads that last
better. This summer I will replace the rotors - not a fun job on the
Hyundai. They are chewed up enough I will have problems with
inspection but the car stops fine.
The deal with the rear's is an intermittent high pitched sound that I
seems to be coming from the back end. I tried pulling the drum the
other day but it was rusted to the metal cover for the bearing. I
will get if off today or tomorrow and see what is going on. It may be
nothing more than a new pair of shoes.
The thing with Hyundai parts that is throwing me is the cost compared
to the Ford car and Chevy truck I also work on. When I can replace
drums for $20 ea it is cheap enough and easier than getting them
turned. At $50 it is not a good option. I will admit I have gotten
lazy in that it is much easier to throw $100 worth of parts into
something and be done rather than to figure out what $100 part out of
several is the real problem. ;-)
#6
Guest
Posts: n/a
Re: 99 Accent axel bearing question
Don't feel bad. I fully diagnose customer's vehicles, but when it comes to
my own, I typically run out and buy whatever part I think is screwing me
up.
As for getting your drums off, screwing two 8mm x 1.25 bolts into the
holes in the drums should help push them off.
my own, I typically run out and buy whatever part I think is screwing me
up.
As for getting your drums off, screwing two 8mm x 1.25 bolts into the
holes in the drums should help push them off.
#7
Guest
Posts: n/a
Re: 99 Accent axel bearing question
"nothermark"
> >I've got a high pitched sqeak sometimes when the car is rolling.
> >Braking stops it.
I have this same issue with my '02 Santa Fe (40K miles). I had the
brakes replaced last week, rotors are fine. The high pitched squeal
remains. It usually shows up after going down the road for 15 min
or so. It's also more noticeable when turning left. It's in the passenger
rear. Braking stops it.
All signs point to the rear hub which, I have a feeling, isn't covered. :-\
Ruth CM
> >I've got a high pitched sqeak sometimes when the car is rolling.
> >Braking stops it.
I have this same issue with my '02 Santa Fe (40K miles). I had the
brakes replaced last week, rotors are fine. The high pitched squeal
remains. It usually shows up after going down the road for 15 min
or so. It's also more noticeable when turning left. It's in the passenger
rear. Braking stops it.
All signs point to the rear hub which, I have a feeling, isn't covered. :-\
Ruth CM
Thread
Thread Starter
Forum
Replies
Last Post
honda video
Honda Videos
0
03-20-2008 09:19 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)