Last Update - 93 Honda overheating - Ground problem?
01-01-2004, 04:58 PM
#16
Guest
Posts: n/a
Re: Last Update - 93 Honda overheating - Ground problem?
In article <15qIb.92999$UY6.48426@twister.nyroc.rr.com>, "WORSS"
<wrector@nospam.nycap.rr.com> wrote:
> Again, thanks for your inputs.
>
> I have followed the Honda repair procedure for both the condensor fan and
> radiator fans not working. I have checked all the continuity between all
> the points it suggests and have checked the fans and even the diode. All
> checked out okay. The next thing it says to do is to check continuity of
> the black wire connecting the radiator fan control module (timer module) and
> ground. I SEEM TO HAVE AN OPEN CIRCUIT!!!!! According to the manual...if
> I had continuity, this would lead one to conclude that the module had
> failed. BUT.....I don't have continuity so it just says to "fix" the
> grounding problem. At this point I am lost because there are so many damn
> grounds on this car!
>
> However....I did check the main ground coming off the negative terminal of
> the battery and I would estimate that at least half of the wires have broken
> off the connector that is bolted to the engine block. I realize that this
> is an issue and should be fixed, but could this be my problem? This ground
> must impact every ground on the car....everything else seems to be working
> correctly?
>
> Thanks,
> Bill
I believe that it is very possible that you are on the right track--It's
my guess that one of wires that you mentioned in the last paragraph is the
source of the problem. After you reconnect the wires--your problem related
to the radiator fans will (hopefully) be fixed.
<wrector@nospam.nycap.rr.com> wrote:
> Again, thanks for your inputs.
>
> I have followed the Honda repair procedure for both the condensor fan and
> radiator fans not working. I have checked all the continuity between all
> the points it suggests and have checked the fans and even the diode. All
> checked out okay. The next thing it says to do is to check continuity of
> the black wire connecting the radiator fan control module (timer module) and
> ground. I SEEM TO HAVE AN OPEN CIRCUIT!!!!! According to the manual...if
> I had continuity, this would lead one to conclude that the module had
> failed. BUT.....I don't have continuity so it just says to "fix" the
> grounding problem. At this point I am lost because there are so many damn
> grounds on this car!
>
> However....I did check the main ground coming off the negative terminal of
> the battery and I would estimate that at least half of the wires have broken
> off the connector that is bolted to the engine block. I realize that this
> is an issue and should be fixed, but could this be my problem? This ground
> must impact every ground on the car....everything else seems to be working
> correctly?
>
> Thanks,
> Bill
I believe that it is very possible that you are on the right track--It's
my guess that one of wires that you mentioned in the last paragraph is the
source of the problem. After you reconnect the wires--your problem related
to the radiator fans will (hopefully) be fixed.
01-01-2004, 04:58 PM
#17
Guest
Posts: n/a
Re: Last Update - 93 Honda overheating - Ground problem?
In article <15qIb.92999$UY6.48426@twister.nyroc.rr.com>, "WORSS"
<wrector@nospam.nycap.rr.com> wrote:
> Again, thanks for your inputs.
>
> I have followed the Honda repair procedure for both the condensor fan and
> radiator fans not working. I have checked all the continuity between all
> the points it suggests and have checked the fans and even the diode. All
> checked out okay. The next thing it says to do is to check continuity of
> the black wire connecting the radiator fan control module (timer module) and
> ground. I SEEM TO HAVE AN OPEN CIRCUIT!!!!! According to the manual...if
> I had continuity, this would lead one to conclude that the module had
> failed. BUT.....I don't have continuity so it just says to "fix" the
> grounding problem. At this point I am lost because there are so many damn
> grounds on this car!
>
> However....I did check the main ground coming off the negative terminal of
> the battery and I would estimate that at least half of the wires have broken
> off the connector that is bolted to the engine block. I realize that this
> is an issue and should be fixed, but could this be my problem? This ground
> must impact every ground on the car....everything else seems to be working
> correctly?
>
> Thanks,
> Bill
I believe that it is very possible that you are on the right track--It's
my guess that one of wires that you mentioned in the last paragraph is the
source of the problem. After you reconnect the wires--your problem related
to the radiator fans will (hopefully) be fixed.
<wrector@nospam.nycap.rr.com> wrote:
> Again, thanks for your inputs.
>
> I have followed the Honda repair procedure for both the condensor fan and
> radiator fans not working. I have checked all the continuity between all
> the points it suggests and have checked the fans and even the diode. All
> checked out okay. The next thing it says to do is to check continuity of
> the black wire connecting the radiator fan control module (timer module) and
> ground. I SEEM TO HAVE AN OPEN CIRCUIT!!!!! According to the manual...if
> I had continuity, this would lead one to conclude that the module had
> failed. BUT.....I don't have continuity so it just says to "fix" the
> grounding problem. At this point I am lost because there are so many damn
> grounds on this car!
>
> However....I did check the main ground coming off the negative terminal of
> the battery and I would estimate that at least half of the wires have broken
> off the connector that is bolted to the engine block. I realize that this
> is an issue and should be fixed, but could this be my problem? This ground
> must impact every ground on the car....everything else seems to be working
> correctly?
>
> Thanks,
> Bill
I believe that it is very possible that you are on the right track--It's
my guess that one of wires that you mentioned in the last paragraph is the
source of the problem. After you reconnect the wires--your problem related
to the radiator fans will (hopefully) be fixed.
01-16-2004, 04:22 PM
#18
Guest
Posts: n/a
Re: Last Update - 93 Honda overheating - Ground problem?
You're supposed to get continuity between the black wire and ground, you
said. If this wire is one of the broken wires you found at that ground on
the block then you should get continuity when you connect the test lead you
normally would connect to ground to one of the dangling ends. Perhaps
you'll have to trip the ends first but you should be doing that anyway
because you should repair those broken wires for the longevity of the car.
Some parts may be pulling current through others to complete the circuit if
their ground is gone. This can do damage over time that isn't done
immediately.
"WORSS" <wrector@nospam.nycap.rr.com> wrote in message
news:15qIb.92999$UY6.48426@twister.nyroc.rr.com...
> Again, thanks for your inputs.
>
> I have followed the Honda repair procedure for both the condensor fan and
> radiator fans not working. I have checked all the continuity between all
> the points it suggests and have checked the fans and even the diode. All
> checked out okay. The next thing it says to do is to check continuity of
> the black wire connecting the radiator fan control module (timer module)
and
> ground. I SEEM TO HAVE AN OPEN CIRCUIT!!!!! According to the
manual...if
> I had continuity, this would lead one to conclude that the module had
> failed. BUT.....I don't have continuity so it just says to "fix" the
> grounding problem. At this point I am lost because there are so many damn
> grounds on this car!
>
> However....I did check the main ground coming off the negative terminal of
> the battery and I would estimate that at least half of the wires have
broken
> off the connector that is bolted to the engine block. I realize that this
> is an issue and should be fixed, but could this be my problem? This
ground
> must impact every ground on the car....everything else seems to be working
> correctly?
>
> Thanks,
> Bill
>
>
said. If this wire is one of the broken wires you found at that ground on
the block then you should get continuity when you connect the test lead you
normally would connect to ground to one of the dangling ends. Perhaps
you'll have to trip the ends first but you should be doing that anyway
because you should repair those broken wires for the longevity of the car.
Some parts may be pulling current through others to complete the circuit if
their ground is gone. This can do damage over time that isn't done
immediately.
"WORSS" <wrector@nospam.nycap.rr.com> wrote in message
news:15qIb.92999$UY6.48426@twister.nyroc.rr.com...
> Again, thanks for your inputs.
>
> I have followed the Honda repair procedure for both the condensor fan and
> radiator fans not working. I have checked all the continuity between all
> the points it suggests and have checked the fans and even the diode. All
> checked out okay. The next thing it says to do is to check continuity of
> the black wire connecting the radiator fan control module (timer module)
and
> ground. I SEEM TO HAVE AN OPEN CIRCUIT!!!!! According to the
manual...if
> I had continuity, this would lead one to conclude that the module had
> failed. BUT.....I don't have continuity so it just says to "fix" the
> grounding problem. At this point I am lost because there are so many damn
> grounds on this car!
>
> However....I did check the main ground coming off the negative terminal of
> the battery and I would estimate that at least half of the wires have
broken
> off the connector that is bolted to the engine block. I realize that this
> is an issue and should be fixed, but could this be my problem? This
ground
> must impact every ground on the car....everything else seems to be working
> correctly?
>
> Thanks,
> Bill
>
>
01-16-2004, 04:22 PM
#19
Guest
Posts: n/a
Re: Last Update - 93 Honda overheating - Ground problem?
You're supposed to get continuity between the black wire and ground, you
said. If this wire is one of the broken wires you found at that ground on
the block then you should get continuity when you connect the test lead you
normally would connect to ground to one of the dangling ends. Perhaps
you'll have to trip the ends first but you should be doing that anyway
because you should repair those broken wires for the longevity of the car.
Some parts may be pulling current through others to complete the circuit if
their ground is gone. This can do damage over time that isn't done
immediately.
"WORSS" <wrector@nospam.nycap.rr.com> wrote in message
news:15qIb.92999$UY6.48426@twister.nyroc.rr.com...
> Again, thanks for your inputs.
>
> I have followed the Honda repair procedure for both the condensor fan and
> radiator fans not working. I have checked all the continuity between all
> the points it suggests and have checked the fans and even the diode. All
> checked out okay. The next thing it says to do is to check continuity of
> the black wire connecting the radiator fan control module (timer module)
and
> ground. I SEEM TO HAVE AN OPEN CIRCUIT!!!!! According to the
manual...if
> I had continuity, this would lead one to conclude that the module had
> failed. BUT.....I don't have continuity so it just says to "fix" the
> grounding problem. At this point I am lost because there are so many damn
> grounds on this car!
>
> However....I did check the main ground coming off the negative terminal of
> the battery and I would estimate that at least half of the wires have
broken
> off the connector that is bolted to the engine block. I realize that this
> is an issue and should be fixed, but could this be my problem? This
ground
> must impact every ground on the car....everything else seems to be working
> correctly?
>
> Thanks,
> Bill
>
>
said. If this wire is one of the broken wires you found at that ground on
the block then you should get continuity when you connect the test lead you
normally would connect to ground to one of the dangling ends. Perhaps
you'll have to trip the ends first but you should be doing that anyway
because you should repair those broken wires for the longevity of the car.
Some parts may be pulling current through others to complete the circuit if
their ground is gone. This can do damage over time that isn't done
immediately.
"WORSS" <wrector@nospam.nycap.rr.com> wrote in message
news:15qIb.92999$UY6.48426@twister.nyroc.rr.com...
> Again, thanks for your inputs.
>
> I have followed the Honda repair procedure for both the condensor fan and
> radiator fans not working. I have checked all the continuity between all
> the points it suggests and have checked the fans and even the diode. All
> checked out okay. The next thing it says to do is to check continuity of
> the black wire connecting the radiator fan control module (timer module)
and
> ground. I SEEM TO HAVE AN OPEN CIRCUIT!!!!! According to the
manual...if
> I had continuity, this would lead one to conclude that the module had
> failed. BUT.....I don't have continuity so it just says to "fix" the
> grounding problem. At this point I am lost because there are so many damn
> grounds on this car!
>
> However....I did check the main ground coming off the negative terminal of
> the battery and I would estimate that at least half of the wires have
broken
> off the connector that is bolted to the engine block. I realize that this
> is an issue and should be fixed, but could this be my problem? This
ground
> must impact every ground on the car....everything else seems to be working
> correctly?
>
> Thanks,
> Bill
>
>
01-16-2004, 04:22 PM
#20
Guest
Posts: n/a
Re: Last Update - 93 Honda overheating - Ground problem?
You're supposed to get continuity between the black wire and ground, you
said. If this wire is one of the broken wires you found at that ground on
the block then you should get continuity when you connect the test lead you
normally would connect to ground to one of the dangling ends. Perhaps
you'll have to trip the ends first but you should be doing that anyway
because you should repair those broken wires for the longevity of the car.
Some parts may be pulling current through others to complete the circuit if
their ground is gone. This can do damage over time that isn't done
immediately.
"WORSS" <wrector@nospam.nycap.rr.com> wrote in message
news:15qIb.92999$UY6.48426@twister.nyroc.rr.com...
> Again, thanks for your inputs.
>
> I have followed the Honda repair procedure for both the condensor fan and
> radiator fans not working. I have checked all the continuity between all
> the points it suggests and have checked the fans and even the diode. All
> checked out okay. The next thing it says to do is to check continuity of
> the black wire connecting the radiator fan control module (timer module)
and
> ground. I SEEM TO HAVE AN OPEN CIRCUIT!!!!! According to the
manual...if
> I had continuity, this would lead one to conclude that the module had
> failed. BUT.....I don't have continuity so it just says to "fix" the
> grounding problem. At this point I am lost because there are so many damn
> grounds on this car!
>
> However....I did check the main ground coming off the negative terminal of
> the battery and I would estimate that at least half of the wires have
broken
> off the connector that is bolted to the engine block. I realize that this
> is an issue and should be fixed, but could this be my problem? This
ground
> must impact every ground on the car....everything else seems to be working
> correctly?
>
> Thanks,
> Bill
>
>
said. If this wire is one of the broken wires you found at that ground on
the block then you should get continuity when you connect the test lead you
normally would connect to ground to one of the dangling ends. Perhaps
you'll have to trip the ends first but you should be doing that anyway
because you should repair those broken wires for the longevity of the car.
Some parts may be pulling current through others to complete the circuit if
their ground is gone. This can do damage over time that isn't done
immediately.
"WORSS" <wrector@nospam.nycap.rr.com> wrote in message
news:15qIb.92999$UY6.48426@twister.nyroc.rr.com...
> Again, thanks for your inputs.
>
> I have followed the Honda repair procedure for both the condensor fan and
> radiator fans not working. I have checked all the continuity between all
> the points it suggests and have checked the fans and even the diode. All
> checked out okay. The next thing it says to do is to check continuity of
> the black wire connecting the radiator fan control module (timer module)
and
> ground. I SEEM TO HAVE AN OPEN CIRCUIT!!!!! According to the
manual...if
> I had continuity, this would lead one to conclude that the module had
> failed. BUT.....I don't have continuity so it just says to "fix" the
> grounding problem. At this point I am lost because there are so many damn
> grounds on this car!
>
> However....I did check the main ground coming off the negative terminal of
> the battery and I would estimate that at least half of the wires have
broken
> off the connector that is bolted to the engine block. I realize that this
> is an issue and should be fixed, but could this be my problem? This
ground
> must impact every ground on the car....everything else seems to be working
> correctly?
>
> Thanks,
> Bill
>
>
01-16-2004, 04:22 PM
#21
Guest
Posts: n/a
Re: Last Update - 93 Honda overheating - Ground problem?
You're supposed to get continuity between the black wire and ground, you
said. If this wire is one of the broken wires you found at that ground on
the block then you should get continuity when you connect the test lead you
normally would connect to ground to one of the dangling ends. Perhaps
you'll have to trip the ends first but you should be doing that anyway
because you should repair those broken wires for the longevity of the car.
Some parts may be pulling current through others to complete the circuit if
their ground is gone. This can do damage over time that isn't done
immediately.
"WORSS" <wrector@nospam.nycap.rr.com> wrote in message
news:15qIb.92999$UY6.48426@twister.nyroc.rr.com...
> Again, thanks for your inputs.
>
> I have followed the Honda repair procedure for both the condensor fan and
> radiator fans not working. I have checked all the continuity between all
> the points it suggests and have checked the fans and even the diode. All
> checked out okay. The next thing it says to do is to check continuity of
> the black wire connecting the radiator fan control module (timer module)
and
> ground. I SEEM TO HAVE AN OPEN CIRCUIT!!!!! According to the
manual...if
> I had continuity, this would lead one to conclude that the module had
> failed. BUT.....I don't have continuity so it just says to "fix" the
> grounding problem. At this point I am lost because there are so many damn
> grounds on this car!
>
> However....I did check the main ground coming off the negative terminal of
> the battery and I would estimate that at least half of the wires have
broken
> off the connector that is bolted to the engine block. I realize that this
> is an issue and should be fixed, but could this be my problem? This
ground
> must impact every ground on the car....everything else seems to be working
> correctly?
>
> Thanks,
> Bill
>
>
said. If this wire is one of the broken wires you found at that ground on
the block then you should get continuity when you connect the test lead you
normally would connect to ground to one of the dangling ends. Perhaps
you'll have to trip the ends first but you should be doing that anyway
because you should repair those broken wires for the longevity of the car.
Some parts may be pulling current through others to complete the circuit if
their ground is gone. This can do damage over time that isn't done
immediately.
"WORSS" <wrector@nospam.nycap.rr.com> wrote in message
news:15qIb.92999$UY6.48426@twister.nyroc.rr.com...
> Again, thanks for your inputs.
>
> I have followed the Honda repair procedure for both the condensor fan and
> radiator fans not working. I have checked all the continuity between all
> the points it suggests and have checked the fans and even the diode. All
> checked out okay. The next thing it says to do is to check continuity of
> the black wire connecting the radiator fan control module (timer module)
and
> ground. I SEEM TO HAVE AN OPEN CIRCUIT!!!!! According to the
manual...if
> I had continuity, this would lead one to conclude that the module had
> failed. BUT.....I don't have continuity so it just says to "fix" the
> grounding problem. At this point I am lost because there are so many damn
> grounds on this car!
>
> However....I did check the main ground coming off the negative terminal of
> the battery and I would estimate that at least half of the wires have
broken
> off the connector that is bolted to the engine block. I realize that this
> is an issue and should be fixed, but could this be my problem? This
ground
> must impact every ground on the car....everything else seems to be working
> correctly?
>
> Thanks,
> Bill
>
>
Thread
Thread Starter
Forum
Replies
Last Post
michael1986morgan
Honda Accord
0
01-14-2008 07:35 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)